Alcatel OmniStack 8008 Manuel utilisateur

Part No. 060118-10, Rev. A

December 2000

OmniStack®8008

Getting Started Guide

SwitchExpertSMSM Service Programs: An Alcatel service agreement brings your

company the assurance of 7x24 no-excuses technical support. You’ll also receive

regular software updates to maintain and maximize your Alcatel product’s features

and functionality and on-site hardware replacement through our global network of

highly qualified service delivery partners. Additionally, with 24-hour-a-day access to

Alcatel’s Service and Support web page, you’ll be able to view and update any case

(open or closed) that you have reported to Alcatel’s technical support, open a new case

or access helpful release notes, technical bulletins, and manuals. For more

information on Alcatel’s Service Programs, see our web page at

www.ind.alcatel.com, call us at 1-800-995-2696, or email us at

switchexper[email protected]m.

This Manual documents OmniStack 8008 hardware and software.

The functionality described in this Manual is subject to change without notice.

reproduced in whole or in part without the express written permission of Alcatel Internetworking, Inc.

Alcatel® and the Alcatel logo are registered trademarks of Compagnie Financiére Alcatel, Paris,

France. OmniSwitch®and OmniStack®are registered trademarks of Alcatel Internetworking, Inc.

Omni Switch/Routerô, SwitchExpertSM, the Xylan logo are trademarks of Alcatel Internetworking,

Inc. All other brand and product names are trademarks of their respective companies.

26801 West Agoura Road

Calabasas, CA 91301

(818) 880-3500 FAX (818) 880-3505

inf[email protected]lcatel.com

US Customer Support-(800) 995-2696

International Customer Support-(818) 878-4507

Internet-http://www.ind.alcatel.com

Warning

This equipment has been tested and found to comply with the limits for Class B digital

device pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in a

commercial environment. This equipment generates, uses, and can radiate radio fre-

quency energy and, if not installed and used in accordance with the instructions in this

guide, may cause interference to radio communications. Operation of this equipment in

a residential area is likely to cause interference, in which case the user will be required

to correct the interference at his own expense.

The user is cautioned that changes and modifications made to the equipment without

approval of the manufacturer could void the user’s authority to operate this equipment.

It is suggested that the user use only shielded and grounded cables to ensure compliance

with FCC Rules.

This digital apparatus does not exceed the Class B limits for radio noise emissions from

digital apparatus set out in the radio interference regulations of the Canadian depart-

ment of communications.

Le present appareil numerique níemet pas de bruits radioelectriques depassant les lim-

ites applicables aux appareils numeriques de la Class B prescrites dans le reglement sur

le brouillage radioelectrique edicte par le ministere des communications du Canada.

Contents

Introduction 1

Installing the Switch 2

Package Contents 2

Description of Hardware 2

Mounting the Switch 3

Stacking Switches on a Flat Surface 3

Mounting Switches in a Rack 3

Connecting the Switch System 4

Connecting to a Gigabit Port 4

Powering On the Switch 5

Verifying Port Status 5

Verifying System Operation 5

Applications 6

Product Specifications 7

Troubleshooting 8

Diagnosing Switch Indicators 8

Power and Cooling Problems 8

Installation 8

EMI Certification 9

FCC Class B Certification (USA) 9

Canada Department of Communications - Class B 9

BSMI Class A (Taiwan) 10

VCCI Class B Compliance (Japan) 10

CE Mark Declaration of Conformance 10

Safety Compliance 11

Warning: Fiber Optic Port Safety 11

Avertissment: Ports pour fibres optiques - sécurité sur le plan optique 11

Warnhinweis: Faseroptikanschlüsse - Optische Sicherheit 11

Underwriters Laboratories Compliance Statement 11

Wichtige Sicherheitshinweise (Germany) 12

Optional Hardware 12

Contents

Introduction

The Alcatel Omnistack®8008 is a high-performance Gigabit Ethernet switch designed for

the network core. It provides 8 1000BASE-SX ports that can significantly improve the

performance of your network’s backbone, and deliver the throughput needed to support a

broad range of advanced network applications.

With 16 Gigabits of aggregate bandwidth, this Alcatel switch provides the quickest

solution to meeting the growing demands on your network’s limited resources. Each

1000BASE-SX fiber optic port can support connections up to 550 meters (1800 feet),

providing high-bandwidth connectivity within or between workgroups, and increased

capacity for server farms, giving your users faster access to network-wide resources.

The Alcatel Omnistack®includes a built-in management agent that allows you to

configure or monitor the switch using the embedded management program or SNMP/

RMON applications. To manage the switch, you can make a direct connection to the

console port. You can also make a network connection to manage the switch using

Telnet, the on-board Web agent, or any SNMP-based network management software.

By accessing the management agent you can configure the switch’s wide array of

advanced features, such as:

• Agent supports Telnet, SNMP/RMON and Web-based interface

• Basic RMON (including Statistics, History, Alarms and Events)

• Spanning Tree Algorithm for redundant paths between switches

• Full-duplex flow control (IEEE 802.3x)

• Broadcast storm control (broadcast packets dropped at a configurable threshold)

• Port mirroring (for real-time debugging without affecting the target port)

• VLAN support for up to 256 groups, port-based or with 802.1Q VLAN tagging

• Multicast filtering with IGMP snooping

• Quality of Service supports two levels of priority with Weighted Fair Queueing

Omnistack®8008

Installing the Switch

Before installing the switch verify that you have all the items listed under “Package

Contents.” If any of the items are missing or damaged, contact your local Alcatel

distributor. Also be sure you have all the necessary tools and cabling before installing the

switch. Note that this switch can be installed on any suitably large flat surface or in a

standard EIA 19-inch rack. After installing the switch, refer to the Users Guide to set up its

more advanced features, such as Spanning Tree Protocol or VLAN port groups.

Package Contents

This package includes:

Description of Hardware

The switch contains 8 1000BASE-SX fiber optic ports. An SNMP/RMON management

agent is built into the switch unit with a serial port provided on the rear panel for

out-of-band console configuration. The AC power socket and redundant power supply

connector are also located on the rear panel.

All the SC-type ports operate at 1000 Mbps full and half duplex and support

auto-negotiation of duplex mode and flow control. When using auto-negotiation, the

transmission mode, and flow control can be automatically set if this feature is also

supported by the attached device.

The switch also includes an LED display panel for key system and port indications that

simplify installation and network troubleshooting.

The following figure shows the components of this switch:

•Omnistack

®8008 (Model No. OS-8008)

• Four rubber foot pads

• Rack mount bracket kit

• AC power cord

• Console cable

• This Getting Started Guide

• Owner registration card

• Users Guide

Installing the Switch

Mounting the Switch

This switch can be placed directly on your desktop, or mounted in a rack.

Before you start installing the switch, make sure you can provide the right operating

environment, including power requirements, sufficient physical space, and proximity to

other devices that are to be connected. Verify the following requirements:

• Power requirements: 100 to 240 VAC (± 10%) at 50 to 60 Hz (± 3Hz). The switch's

power supply automatically adjusts to the input voltage level.

• The switch should be located in a cool dry place, with at least 10 cm (4 in.) of space on

the sides for ventilation.

• Place the switch out of direct sunlight, and away from heat sources or areas with a high

amount of electromagnetic interference.

• If you intend to mount the switch in a rack, make sure you have all the necessary

mounting screws, brackets, bolts and nuts, and the right tools.

• Check if network cables and connectors needed for installation are available.

Stacking Switches on a Flat Surface

The Omnistack®8008 can be stacked

anywhere there is enough flat space, such as

on a table or desktop.

1. Stick the self-adhesive rubber foot pads

(that come with this package) on each of

the 4 concave spaces located on the

bottom of the switch.

2. Place the first switch on a firm flat surface where you want to install the stack.

3. Repeat step 1 for each switch before stacking them. The rubber foot pads cushion

the switch against shock/vibrations and provide space between each switch for

ventilation.

Mounting Switches in a Rack

Please comply with the following instructions to ensure

that your switch is securely mounted in the rack.

1. Use a standard EIA 19-inch rack.

2. Use the brackets and screws supplied in the rack

mounting kit.

3. Use a Philips screwdriver to attach the brackets to

the side of the switch.

4. Position the switch in the rack by lining up the holes in the brackets with the

appropriate holes on the rack, and then use the rack-mount screws to mount the

switch in the rack.

Omnistack®8008

Connecting the Switch System

The OmniStack®8008 provides 8 SC-type fiber optic ports. Each of these ports support

connection to 1000 Mbps Gigabit Ethernet.

Connecting to a Gigabit Port

When connecting fiber cable to a 1000BASE-SX port on the switch, be sure you use an

SC-type connector. Follow the steps below.

Warning: This switch uses lasers to transmit signals over fiber optic cable. The lasers are

compliant with the requirements of a Class 1 Laser Product and are inherently eye

safe in normal operation. However, you should never look directly at a transmit port

when it is powered on.

1. Remove and keep the SC port’s rubber cover. When not connected to a fiber cable,

the rubber cover should be replaced to protect the optics.

2. Check that the fiber terminators are clean. You can clean the cable plugs by wiping

them gently with a clean tissue or cotton ball moistened with a little ethanol. Dirty

fiber terminators on fiber optic cables will impair the quality of the light transmitted

through the cable and lead to degraded performance on the port.

3. Connect one end of the cable to the SC port on the switch and the other end to the

SC port on the other device. Since SC connectors are keyed, the cable can be

attached in only one orientation. When inserting the cable, be sure the tab on the

plug clicks into position to ensure that it is properly seated.

All the SC-type ports operate at 1 Gbps with support for auto-negotiation of duplex mode

(full/half) and flow control. Also note the maximum length for 1000BASE-SX fiber optic

cable depends on the core size and the rating of the cable, as shown in the following

table.

Fiber Size Fiber Bandwidth Maximum Cable Length

62.5/125 micron 160 MHz/km 220 m (722 ft)

200 MHz/km 275 m (902 ft)

50/125 micron 400 MHz/km 500 m (1641 ft)

500 MHz/km 550 m (1805 ft)

Autres manuels pour OmniStack 8008

Table des matières

Autres manuels Alcatel Changer

Alcatel

Alcatel OmniAccess 4308 Manuel utilisateur

Alcatel

Alcatel OmniSwitch 6600 Family Manuel utilisateur

Alcatel

Alcatel OmniAccess 2.0 Manuel utilisateur

Alcatel

Alcatel OmniStack 6124 Manuel utilisateur

Alcatel

Alcatel omniaccess 4302 Manuel utilisateur

Alcatel

Alcatel 1850 TSS-320 Manuel utilisateur

Alcatel

Alcatel OmniPCX 4400 Manuel utilisateur

Alcatel

Alcatel OmniSwitch 6800 Comment utiliser

Alcatel

Alcatel OmniSwitch 6600 Manuel du propriétaire

Alcatel

Alcatel OmniStack 6148 Manuel utilisateur

Alcatel

Alcatel OmniSwitch 7700 Manuel d'installation

Alcatel

Alcatel OmniSwitch 6600 Family Manuel utilisateur

Alcatel

Alcatel LinkHub HH70VH Manuel utilisateur

Alcatel

Alcatel OmniSwitch 6624 Manuel de programmation

Alcatel

Alcatel OmniStack LS 6248 Manuel utilisateur

Alcatel

Alcatel 1850 TSS-320 Note de version

Alcatel

Alcatel OmniSwitch 6624 Manuel utilisateur

Alcatel

Alcatel OmniSwitch 6600 Manuel d'installation

Alcatel

Alcatel OmniStack 4024 Manuel utilisateur

Alcatel

Alcatel OmniSwitch 9000 Manuel utilisateur

Alcatel

Alcatel OAW-LC-2G24F Manuel utilisateur

Alcatel

Alcatel OmniAccess 512 Manuel utilisateur

Alcatel

Alcatel 7450 ESS-7 Manuel utilisateur

Alcatel

Alcatel OS6850-P48 Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur