Alarmcom ADC-T2000 Manuel utilisateur

www.alarm.com • 1-877-389-4033

Smart Thermostat

ADC-T2000

Quick

Installation

Guide

Alarm.com Logo are registered trademarks of Alarm.com.

www.alarm.com •1-877-389-4033

Pull up your customer’s account

and select the emPower® button.

Click on Z-Wave Devices and

select the Smart Thermostat.

Review and update Installer

settings to configure.

Configure Your Thermostat

Using MobileTech

Use MobileTech to quickly configure your

new Smart Thermostat.

Download MobileTech today!

www.alarm.com/mobiletech

12 Congure your system

You must program the thermostat settings

(or run through the online setup wizard)

before putting the thermostat into heating or

cooling mode.

Visit the Alarm.com Dealer Website or use

MobileTech to congure the system parameters.

Dealer Website > Customers > Equipment >

emPower Devices > Congure Device

For more detailed instructions, please visit:

Dealer Website > Support & Sales >

Support Documentation

For questions, please contact

[email protected].

Connect the Thermostat

to the system

Now you can connect the Alarm.com Smart

Thermostat to the Alarm.com home system

using the Z-Wave network.

To pair, make sure the thermostat is in

OFF mode (no mode icons are lit) and press

and hold the DOWN  ) button until you

see the RADIO ( ) icon.

Disconnect the existing

thermostat

Disconnect all wires and remove the

thermostat base.

TIP: Check that all wires are a proper

gauge (18-24 AWG), have approximately

1/8” exposed straight ends, and are in

good condition.

Install the new back plate

If necessary, rst install the optional trim

plate to cover any holes or marks left from

the old thermostat.

Connect the wires

Reconnect the wires and record the new

connections (you may want to take

another picture).

TIP: If you have RH & RC, remove the

black jumper in the lower left corner

of the back plate terminal board with

needle-nose pliers.

O/B

Jumper On

O/B

Jumper O

Install the batteries

Attach the Alarm.com

Smart Thermostat

Make sure that any excess wire is

tucked back into the wall and press the

thermostat rmly into the back plate.

Turn the power on

Restore the power at the circuit breaker.

Test the system

Verify that the heating and/or cooling system is

operating properly with the existing thermostat.

CAUTION: If the existing thermostat is labeled

120V or 240V, or has thick wires with wire nuts,

the system is high voltage. Do not install the new

thermostat to a high voltage system.

Turn power off

Turn the heating

and cooling

system off at the

circuit breaker.

Remove the existing

thermostat cover

Label all existing wires

Carefully label each wire with

the provided labels.

TIP: Take a picture

of the existing

wiring before

disconnecting.

Continued on back

Autres manuels pour ADC-T2000

Table des matières

Autres manuels Alarmcom Thermostat

Alarmcom

Alarmcom ADC-T2000 Manuel utilisateur

Alarmcom

Alarmcom ADC-T2000 Manuel utilisateur

Alarmcom

Alarmcom ADC-T40K-HD Manuel utilisateur

Alarmcom

Alarmcom ADC-T2000 Manuel utilisateur

Alarmcom

Alarmcom Building 36 ADC-T3000 Manuel utilisateur

Alarmcom

Alarmcom ADC-T3000 Manuel utilisateur

Alarmcom

Alarmcom ADC-T40K-HD Manuel utilisateur

Alarmcom

Alarmcom ADC-T3000 Manuel utilisateur

Alarmcom

Alarmcom ADC-T2000-RC Manuel utilisateur

Alarmcom

Alarmcom ADC-T3000 Manuel utilisateur

Manuels Thermostat populaires d'autres marques

EWELLY

EWELLY EW-181 Manuel utilisateur

Prolon

Prolon T1100 Instructions d'installation

Computherm

Computherm Q20 Manuel utilisateur

Heatmiser

Heatmiser neoStat Manuel utilisateur

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Manuel utilisateur

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Manuel utilisateur

Saswell

Saswell SAS920XWHB-7-S-RF Mode d’emploi

Aircalo

Aircalo TFP1-ET85P2 Manuel utilisateur

Honeywell

Honeywell CM721 Manuel utilisateur

Carrier

Carrier DEBONAIR 33CS Manuel utilisateur

Lennox

Lennox iHarmony Zone Thermostat Instructions de montage

Gemtech

Gemtech GT7000 Mode d’emploi

Rollei

Rollei Smartes 45000 Manuel utilisateur

Sinope

Sinope TH1300RF Manuel utilisateur

Honeywell

Honeywell RLV4305 Manuel utilisateur

Honeywell

Honeywell Prestige 2.0 THX9421 Manuel utilisateur

NuTone

NuTone NTBZ48 Instructions d'utilisation d'origine

Stelpro

Stelpro MAESTRO ASMT402AD Manuel utilisateur