Akia Screens EDGEFREE Fixed Frame Screen Manuel utilisateur

EDGEFREE®Fixed Frame Screen

USER'SGUIDE - N Type

Thank you for choosing an Akia Screens fixed frame projection screen!

Congratulations on your new purchase! Please read through this user guide before

utilizing the screen. Correct usage and maintenance will ensure a long productlife.

Care and use instructions:

Dust, dirt, and scratches on the projection surface will affect the picture quality,

please take note of the points below to prevent that from occurring:

Do not touch the projection surface with your hands.

Do not write or draw on the projection surface

Do not use fingers or sharp objects to point on the projection surface; this will

damage the screen material.

Use a soft-damp cloth to clean the projection surface; do not use chemical

cleaning agents or alcohol.

Use clean water when dampening the cleaning cloth and do not rub against the

material to clean it.

Product Description:

TheAeon Seriesisa fixed frame projection screen that usesAkia's EDGE FREE®

technology. The EDGE FREE® design resembles a giant size flat panel TV

display. The Edge free screen includes a bezel trim to further enhance the frame

appearanceandabsorbprojectorovershoot.

Rev.101321NAS www.akiascreens.com U-00235 1

2. Hardware Parts List

Rev.101321NAS www.akiascreens.com U-00235 2

Item

Parts List

100"

125"

145"

150"

Frame Center Joints - M5 (bottom position)

Frame Elbow Joints M5(bottom position)

Edge trim Center Joints M4

Edge trim Elbow Joints M4

M5x6 Screws

Springs

100

Spring Hook

Wall Brackets

35CSK Wall Screws

Hollow Wall anchors

M4x4 Screws

Center Support Bar

White gloves

Spring Edge Trim

Long rod (sides) / Short rod (top/bottom)

2/4

FrameAssembly

Step 1: Position the pieces of the frame in the arrangement shown below.

Corner Connection

Note: Make sure all holes are in alignment and the

frame pieces are flush (no gaps), then fasten the screws.

Corner Connection

Step 2. Place the assembled frame to the side and carefully unroll the screen material

face downon thetopofasoft,cleancloth.

Step3.Insertthefourhorizontaland twoverticalTension Rodsinto thecorresponding

sides of the screen material, while keeping the material lying flat. Careful not to snag

on the holes at the edge of the material during this process, forcing the rods may

damagethescreenmaterial.

Step 4. Connect the elbow joints (b) to the top and bottom sections of the vertical

frame. Once inserted, connect the vertical sections to the horizontal frame sections.

Make sure all holes are in alignment and the frames pieces are flush (no gaps).

They shouldformperfectrightangles.

Rev.101321NAS www.elitescreens.com U-00235 3

To prevent permanent damage to the screen material, be sure your hands are clean for the next step.

Center Support Bar

Step 5.Secure the elbow joints by fasting them with M5x6 screws (e), 4+4 at each corner.

Rev.101321NAS www.akiascreens.com U-00235 4

See illustration on the right side on how to properly install the Support bar.

Insert the support bar's

tip into the frame's

groove in the middle,

then rotate it and insert

the other end on the

other side of frame.

Step6:Two people are suggested for this step. Place the center Support Bar into the top

grove on the back of the frame at the approximate center point. Carefully pull the

bottom horizontal frame outward and place the center Support Bar at the approximate

center point of the frame, carefully release the frame once the bar is centered.

(Seeillustrationbelow)

Spring Attachment Method

Step 7. Once the corners and center support bar are secure, continue attaching the

remainder of the springs to the material. Connect the center of the vertical and

horizontalportionsofthematerial,thenworkyour wayaroundtherestoftheframe.

Screen Material

Note (after all springs have been attached):

Correct material installation -Corners of the screen material are properly wrapped

around the corner edges of the frame and material is evenly tensioned and flat,

creating a nicely taut surface.

Rev.101321NAS www.akiascreens.com U-00235 5

Attention: Do not proceed with the Edge Trim installation until making sure there are no ripples in the material.

Incorrect material installation -The corners of the screen material are not properly

wrapped along the edge of the frame leaving the material with unbalanced tension and

an uneven finish. To correct, detach springs from material at the corner(s) where

materialdoesnotlieflatalong theedgeoftheframe,repositionthematerial sothatitlies

flatandwrapsalongtheedgeoftheframe,andreattachspringstothematerial.

Note: Pleasemake note of the yellow label and spring in the center of the frame. This is

an indicator to start the screen material installation process from the middle area of the

frame.

How to avoid getting ripples on the screen's material surface Solution: Pull and

smooth outthe material using your hand from the center tothe corners, creating a nicely

tautsurfaceasshownbelow.

Rev.101321NAS www.akiascreens.com U-00235 6

1. Connect edge trims E&F to form the top/ bottom trims with the edge trim center

Joints, and then insert them on the top/bottom frames.

2. Connect the side edge trims C with the top/bottom edge trim with elbow joints D.

3. Adjust the trim so that the top and bottom trim pieces are touching and show no gaps

on the corners. Then fasten them with the M4x4 screws. (k)

4. Attach an edge trim spring (N) on the middle of each edge trim (1-6) to the frame

asshow on the left illustration.

Rev.101321NAS www.akiascreens.com U-00235 7

Rev.101321NAS www.akiascreens.com U-00235 8

Note : Make sure the direction of the Screen material is correct before you hang the

screen to the wall. The material is labeled top or bottom.

Table des matières

Autres manuels Akia Screens Écran de projection

Akia Screens

Akia Screens EDGE FREE CLR 2 Series Manuel utilisateur

Akia Screens

Akia Screens EDGE FREE CineWhite UHD-B Series Manuel utilisateur

Akia Screens

Akia Screens EDGE FREE Series Manuel utilisateur

Akia Screens

Akia Screens Motorized Series Manuel utilisateur

Akia Screens

Akia Screens Fixed Frame Screen Series Manuel utilisateur

Akia Screens

Akia Screens Fixed Frame Screen Series Manuel utilisateur

Akia Screens

Akia Screens Folding Frame 120" Manuel utilisateur

Akia Screens

Akia Screens Manual Series Manuel utilisateur

Akia Screens

Akia Screens EDGE FREE CLR 4 Manuel utilisateur

Akia Screens

Akia Screens EDGE FREE CLR 3/4 Series Manuel utilisateur

Akia Screens

Akia Screens EDGE FREE Series Manuel utilisateur

Manuels Écran de projection populaires d'autres marques

FART PRODUKT

FART PRODUKT Standard SCREEN Manuel utilisateur

Draper

Draper E Series Manuel

Elite Screens

Elite Screens Elite Tripod Series Manuel utilisateur

Laarhoven

Laarhoven Companion II Manuel utilisateur

Renogy

Renogy RMS-LFPS-US Manuel utilisateur

Da-Lite

Da-Lite ExecutiveElectrol Manuel utilisateur

Samsung

Samsung S*H65* Manuel utilisateur

FONESTAR

FONESTAR PPTR-43100-FA Manuel utilisateur

Slide Clear

Slide Clear Varro XL Manuel utilisateur

Elite Screens

Elite Screens M85XWS1-SRM Manuel utilisateur

OS РХ-090Н Manuel utilisateur

Niko

Niko 10-845 Manuel utilisateur

Speaka Professional

Speaka Professional 2357532 Manuel d'utilisation

Sima

Sima XL-72 Manuel utilisateur

Jasic

Jasic EVO 2.0 ET-200P Manuel utilisateur

Elite Screens

Elite Screens Starling 2 Series Manuel utilisateur

InFocus

InFocus SC-WALL GRY-92H Manuel

Barco

Barco OverView MVL-615 Manuel utilisateur