Airwell RC15-7ACEL1801 Manuel utilisateur
IMPORTANT NOTE:
Read this manual carefully before installing or operating your new air conditioning unit. Make sure to
save this manual for future reference.
HDA1-20190619-Rev1
User Manual
HDA High Wall
R32 - Product Version 1
Multilingual Manual (EN-FR)
Remote controller 1
Operation instructions
Operation modes 3
Airflow direction control 4
SMART mode 5
SUPER mode 7
ECONOMY mode 8
QUIET mode 7
IFEEL mode 9
TIMER mode 8
DIMMER button 9
CLOCK button 9
SLEEP mode
8°C HEAT mode
10
10
Remote controller Instructions
(RC15-7ACEL1801)
Remote controller
1
5
13
13
The remote controller transmits signals to the system.
FAN SPEED
Used to select fan speed in sequence auto,
higher, high, medium, low and lower.
SMART(invalid for multi system)
Used to enter fuzzy logic operation directly when
the unit is on .
POWER
The appliance will be started when it is
energized or will be stopped when it is
in operation, if you press this button.
MODE
Press this button to select the operation mode.
Remote controller
5
Used to adjust the room temperature and
the timer, also real time.
DIMMER
When you press this button, all the display
of indoor unit will be closed. Press any
button to resume display.
Used to stop or start vertical adjustment
louver swinging and set the desired up/
downairflow direction.
Used to stop or start Horizontal adjustment
louver swinging and set the desired left/right
airflow direction.
QUIET
Used to set or cancel Quiet Mode operation.
ECONOMY
8℃ HEAT(optional)
IFEEL
Used to set or cancel Economy Mode
operation.
Used to start or stop 8℃ HEAT mode.
+
Press to set IFEEL Mode operation.
In IFEEL mode,the Air Conditioner
operates basis temperature sensor
fitted in remote instead of machine,
Advice to use IFEEL mode and the
remote put where the indoor unit
receive signal easily.Press this
button above 5 seconds,start or
stop IFEEL mode.
SUPER
Used to start or stop the fast cooling/heating.
(Fast cooling operates at high fan speed with
16℃61 ) set temp automatically ; Fast heating
operates at auto fan speed with 30℃86°F) set
temp automatically)
( °F
(
13
ON TIMER
Used to set or cancel the timer operation.
SLEEP
Used to set or cancel Sleep Mode operation.
CLOCK
Used to set the current time.
OFF TIMER
Used to set or cancel the timer operation.
11
9
10
16
34
12
6
8
5
12
7
7
14
15
2
13
9
12
10
11
3
1
2
6
5
7
8
4
13
14
16
19
15
SWING
SWING
1
Note: Each mode and relevant function will be further specified in following pages.
Display set timer
Display current time
ON
OFF
Display temperature
Dry indicator Fan only indicator
Auto fan speed
Auto Higher fan speed High fan speed
Cooling indicator
Medium fan speed
Lower fan speed
Smart indicator
Super indicator
IFEEL
Quiet indicator Economy indicator Sleep indicator
8℃ Heat indicator
Heating indicator
Low fan speed
SMARTSMART
Indication symbols on LCD:
TEMP
Remote controller
How to Insert the Batteries
How to Use
Pry open the battery cover according to the arrow direction.
Insert new batteries making sure that the (+) and (-) of battery are matched correctly.
Reattach the cover by pressing it back into position.
Storage and Tips for Using the Remote Controller
The remote controller may be stored mounted on a wall with a holder.
Note: The remote controller holder is an optional part.
remote controller
holder fixing.
remote controller
mounting.
Note:
you have selected.
The shape may differ from that of the remote controller holder
2
To operate the room air conditioner, aim the remote controller
to the signal receptor.The remote controller will operate the air
conditioner at a distance of up to 7m when pointing at signal
receptor of indoor unit.
Remote controller
Note:
Use 2 LR03 AAA(1.5volt) batteries. Do not use rechargeable batteries. Replace batteries with new ones of the same type
when the display becomes dim.
Signal receptor
1.
2.
3.
1 2 3
CAUTIONS
For appropriate signal transmission between remote controller and
indoor unit, keep the signal receiver away from the following items:
Direct sunlight or other strong lights or heat
Flat panel television screen or other electrical appliances that
react to the remote controller
Additionally, the air conditioner will not operate if curtains, doors or
other materials block the signals from the remote controller to the
indoor unit. If the signal may not be transmitted properly, either move
these materials or consult your local dealer.
Operation instructions
The operation modes changed in sequence:
The fan speed is changed in sequence:
Selecting mode
FAN mode
Heating mode is NOT available for cooling only air conditioner.
At "FAN ONLY" mode, only "Auto" is not available.
Some models, such as commercial air conditioner products, only have the third
gear speed.
At "DRY" mode, Fan speed is set at "AUTO” automatically, "FAN SPEED" button
is ineffective in this case.
Operation modes
Result :
Result :
Press button once by once
Press button once by once
Auto
Auto
Higher
High
High
High
Lower
Low
Medium
Medium
HEATING
COOLING
DRY
FAN ONLY
PRESS
PRESS
Auto
Auto
Low
Low
Setting temperature
16℃~30 61℃( )°F~86°F
Range of available set temperature
*HEATING, COOLING
DRY ±7 deg C
unable to set
FAN ONLY
*Note:
Remote controller
*Note: Press and hold “ ” button and “ ” button
together for 2seconds will alternate the temperature display
between the ℃ a nd °F s cale.
*Note: Heating mode is NOT available for cooling only models.
At “Dry” mode, a decrease or rise of up to 7℃ can be set
with if you still feel uncomfortable.
Press button once
Raise temperature setting by 1℃ 1 or °F
Lower temperature setting by 1℃ 1 or °F
Press button once
Result :
Result :
3
Operation instructions
Turning on
SWING , SMART , SUPER , QUIET, TIMER , ECONOMY , IFEEL , DIMMER , CLOCK , and 8℃ HEAT operation modes will
be specified in the following pages.
SLEEP
Changing modes during operation, sometimes the unit does not response at once. Wait 3 minutes.
Wait 3 minutes before restarting the appliance.
During heating operation, air flow is not discharged at the beginning. After 2－5 minutes, the air flow will be discharged
until temperature of indoor heat exchanger rises.
4
Press button .
T he RUN indicator of the indoor unit lights up.
Result :
Vertical airflow(Horizontal airflow) is automatically adjusted to a certain angle in accordance with the
operation mode after turning on the unit.
The direction of airflow can be also adjusted to your own requirement by pressing the " " buttons of
the remote controller.
Operation mode
Direction of airflow
COOLING, DRY
*HEATING,
FAN ONLY
horizontal
downward
Using remote controller to set various angles of flow or specific angle as you like.
*Heating mode is only available for heat pump models.
Airflow direction control
Press " " button once.
Press " " button again .
The louvers swing to a suitable angle as desired.
The vertical adjustment louver will swing up and down automatically.Result :
Result :
Vertical airflow control (with the remote controller)
Using remote controller to set various angles of flow or specific angle as you like.
Press " " button once.
The horizontal adjustment louver will swing left and right automatically.
Result :
Horizontal airflow control (with the remote controller)
PRESS
PRESS
PRESS
PRESS
PRESS
Operation instructions
Do not turn the vertical adjustment louvers manually, otherwise malfunction may occur. If that happens, turn off the
unit first and cut off the power supply, then restore power supply again.
It is better not to let the vertical adjustment louver tilt downward for a long time at COOLING or DRY mode to prevent
condensed water from dripping.
A
B
5
Press " " button again .
The louvers swing to a suitable angle as desired.
Result :
NOTE:If the unit doesn’t have four ways airflow function, you can adjust
horizontal airflow by yourself.(invalid for some models)
PRESS
Indoor temperature Target temperature
21 70℃( ) or below°F 22 7℃( )2°F
26 7℃( )9°FOver 26 7℃( )9°F
21 3°F℃-23℃( )70°F-7
23 9°F℃-26℃( )73°F-7
Operation mode
HEATING
FAN ONLY
DRY
Room temperature
decrease 2 2°F℃( ) after
operate for 3 minutes
COOLING
Heat pump models
Cooling only models
Indoor temperature Target temperature
23 7℃( ) or below3°F
26 7℃( )9°F
Over 26 7℃( )9°F
23 73°F 79°F℃-26℃( - )
Operation mode
FAN ONLY
DRY Room temperature
decrease 2 2°F℃( ) after
operate for 3 minutes
COOLING
How to set SMART mode?
Press the button.
Result : Enters SMART mode(fuzzy logic operation)
directly only when the unit is on .
Temperature and fan speed are automatically
set based on theactual room temperature.
PRESS
SMART mode( )invalid for multi system
For the split-type models, such as wall-mounted air conditioners and some
floor-standing air conditioners, their operation mode and set temperature
should be determined based on the indoor temperature.
Operation mode and temperature are determined by indoor temperature
For commercial air conditioner products, such as cassette type air conditioners, duct type
air conditioners, ceiling & floor air conditioners and some floor-standing air conditioners,
their operation mode should be determined based on the difference between the indoor
temperature and set temperature.
Operation instructions
SMART button is ineffective in SUPER mode.
Your feeling
What you can do in SMART mode?
Button Adjust
Uncomfortable because
of unsuitable air flow
volume.
Uncomfortable because
of unsuitable flow
direction.
Note: Temperature, airflow and direction are controlled automatically in SMART mode.
However, For the on/off, you can choose from -2 to 2 (for some models you can choose
from -7 to 7), for the inverter you can choose from -7 to 7. if you still feel uncomfortable.
6
How to cancel the SMART mode?
Press the button.
Result :
Indoor fan speed alternates among Auto, Higher, High,
Medium, Low and Lower each time this button is
pressed.
Press it once, the vertical adjustment louver(horizontal
adjustment louver) swings to change vertical airflow
direction(horizontal airflow direction). Press it again,
swings stops.
The SMART mode will be cancelled.
Press MODE button cancel SMART mode.
PRESS
ECONOMY button is ineffective in SMART mode.
The operation mode is determined by the difference between the indoor
temperature and set temperature.
Heat pump models
Cooling only models
Indoor temperature Target temperature
Below T-3℃( )3°F T
T
T
Operation mode
HEATING
FAN ONLY
T-3℃T+3℃( )≤T ≤ 3°F
indoor
O3°Fver T+3℃( ) COOLING
Indoor temperature Target temperature
T
T
Operation mode
FAN ONLY
T+3℃( ) or below3°F
O3°F)ver T+3℃( COOLING
Operation instructions
SUPER mode can be set when the appliance is in operation or energized.
Note:
The Appliance will continue working in SUPER mode for 15 minutes , if you don't escape from it
by pressing any of the buttons mentioned above.
SMART button is not available in SUPER mode.
SUPER mode
SUPER mode is used to start or stop fast cooling or heating only when the unit is on.
How to set SUPER mode?
Press button at the cool,dry and fan only mode.
Result : At high fan speed ,the set temperature
automatically to 16℃.(61°F)
Press button at the heat mode.
Result : At auto fan speed ,the set temperature
automatically to 30℃.(86°F)
How to cancel SUPER mode?
7
Press . SUPER , MODE, FAN SPEED, ON/OFF or SLEEP button
Result : The display return to the original mode.
In SUPER mode, you can set temperature, airflow direction or timer
Escape from SUPER mode.
PRESS
Cancel
PRESS
QUIET mode
In this mode, the air conditioner will work with low noise performance by low compressor frequency and low
fan speed. This mode is only available for inverter models.
Note: Press MODE, FAN SPEED, SMART, SUPER, or ON/OFF button
cancel QUIET mode.
ECONOMY
PRESS
ECONOMY button is in SUPER mode.not available
Operation instructions
Timer mode
Note: It is similar to set OFF TIMER , you can make the appliance
switch off automatically at your desired time.
It is convenient to set the timer on with ON TIMER buttons when you go out in the morning to
achieve a comfortable room temperature at the time you get home. You can also set timer off at night to enjoy
a good sleep.
8
Press the or button.
Once to increase or decrease the time setting by 1 minute.
One and a half seconds to increase or decrease the time setting
by 10 minute.
For a longer time to increase or decrease the time by 1 hour.
A "beep" can be heard.
The TIMER indicator on the indoor unit lights up.
(invalid
for multi system)
"ON" stops flashing.
When your desired time displayed on LCD, press the ON TIMER button and confirm it.
After the set timer displayed for 5 seconds the clock will be displayed on the LCD of the remote controller
instead of set timer.
Result :
Result :
Press button.
Press the button.
A "beep" can be heard and the indicator disappears,
the time on mode has been canceled.
Result :
How to cancel ON TIMER ?
How to set ON TIMER ?
Result : “12:00 " flashes on the LCD. ON
1.
2.
3.
4.
PRESS
PRESS
PRESS
PRESS
ECONOMY mode
In this mode, the air conditioner will bring you energy saving performance by lower running currency.
ECONOMY button is ineffective in SUPER and mode.SMART
Press ON/OFF , MODE ,TEMP ∧,TEMP ∨, FAN SPEED , SLEEP ,
QUIET or ECONOMY button cancel ECONOMY mode.
PRESS
Table des matières
Langues :
Autres manuels Airwell Télécommande
Airwell
Airwell RC08C Manuel utilisateur
Airwell
Airwell RCV03 Manuel utilisateur
Airwell
Airwell RC5 Manuel utilisateur
Airwell
Airwell RC18 Manuel utilisateur
Airwell
Airwell RCW4 Manuel utilisateur
Airwell
Airwell RC7 Manuel utilisateur
Airwell
Airwell RWV05 Manuel utilisateur
Airwell
Airwell RC08C Manuel utilisateur
Airwell
Airwell RC08A Manuel utilisateur
Airwell
Airwell RC4 Manuel utilisateur
Manuels Télécommande populaires d'autres marques
Panasonic
Panasonic EUR7622KB0 Manuel utilisateur
Bang & Olufsen
Bang & Olufsen Beo4 Manuel utilisateur
Sunwave Tech.
Sunwave Tech. RemoteComm SRC-7000 Manuel utilisateur
Multiplex
Multiplex PROFI TX 9 Manuel utilisateur
One Remote
One Remote RMB4 Manuel utilisateur
FUTABA
FUTABA 9ZAP - PART2 Manuel utilisateur
