AirTurn BT-105 Manuel utilisateur

BT-105 Transceiver
Product Family
Includes DIGIT, ATFS-2
QUAD and StompKit
User Manual

2
Table of Contents
BT-105 ......................................................................................4
Description............................................................................4
Setup and Pairing.................................................................5
Resetting the Pairing ............................................................5
Turning off the BT-105..........................................................6
Modes...................................................................................6
iOS Virtual Keyboard............................................................8
Charging...............................................................................8
Compatible Switches............................................................9
Tongue and Bite Switches..................................................10
Troubleshooting..................................................................10
Unit Identification................................................................12
DIGIT.......................................................................................13
Setting Modes on the DIGIT...............................................13
Two ATFS-2 Pedal Board Kit..................................................15
Mode Management.............................................................15
QUAD (Four ATFS-2 Pedal Board Kit)....................................16
StompKit (BOSS FS-5U Footswitches)...................................17

3
BOSS FS-6 Footswitches .......................................................18
Changing Modes.................................................................19
Custom Implementation..........................................................20
Warranty..................................................................................20
Radio Information....................................................................21
Recycling and Disposal...........................................................23
Warnings.................................................................................23
Trademarks.............................................................................23
This manual is intended for firmware versions 28 and higher.
The firmware number is the first two digits of the serial number.

4
BT-105
Thank you for your purchase of the AirTurn BT-105 hands free
controller. We hope you enjoy the wonderful convenience of
hands-free page turning, effects (FX) management and other
creative ways to trigger events with the BT-105. Please send
Description
The BT-105 will work with most
Bluetooth-equipped MAC and PC
computers. No additional software
is required. It also works with most
momentary switches to activate
the Page Down and Page Up
functions of most document and
presentation programs, such as Adobe Acrobat, Microsoft
Word, and PowerPoint. The BT-105 can be used with one
footswitch to turn pages forwards only, or with two footswitches
to turn forwards and backwards.
The BT-105 also works with select apps for Apple iOS™
iPhones, iPads, and iPods, in addition to Bluetooth-equipped
Android devices with apps that have been designed to be
compatible with the BT-105.
The BT-105 consists of a power switch, two 3.5mm stereo
jacks for footswitches, an LED indicator, and a mini-USB
charging port for the internal rechargeable battery.

5
Setup and Pairing
To use the BT-105 with your MAC, PC, or iPad, make sure the
host computer you are using is in discovery mode. (Check the
instructions that came with your computer or Bluetooth USB
dongle. For iPad users, go into “Settings”, then select
“Bluetooth” and make sure it is turned on). Turn on the BT-105
by pressing the red power button for 1 second. The LED will
blink green then orange several times and attempt to pair with
your computer. Your host computer may require validation to
accept pairing from the BT-105. If it requires a code, use 0000.
If you are presented a code to validate the BT-105, accept it.
On the iPad, under the “Devices” heading within the Bluetooth
settings, you should see the BT-105 appear, either as a
keyboard, or as “AirTurn” with a serial number. Touch on top of
Serial Number to connect and complete the pairing process.
Once connected, it will blink green once every 2 seconds.
Resetting the Pairing
To reset the pairing on the BT-105, turn it on, wait 3 seconds,
press and hold the red button for 8 seconds until the LED
blinks a rapid series of green and red, then release. If pairing is
unsuccessful, delete the device displayed on the host
computer and reset the BT-105 pairing again. Initial discovery
may take up to 30 seconds (longer on some older PC and
MAC computers). To delete the BT-105 from the iPad’s
Bluetooth Device listing, tap the “i” in the circle opposite the
BT-105’s serial number, then press the “Forget this Device”
button.

6
Note: Reset pairing for both devices each time you change
to a new host device such as using the transceiver with
your desktop computer and then with your iPad.
Turning off the BT-105
Turn off the BT-105 by pressing
the red button for 2-3 seconds
until the LED turns red. Release
and the LED will blink 3 more
times while the unit shuts down.
Turning power off on the host
computer will automatically turn
off the BT-105 after 3 minutes.
Modes
There are four modes that come ready to use on your BT-105.
Modes are used to send different signals to the host computer,
depending on the computer and the application being used.
The default mode, (Mode 3), is set for page turning on tablet
computers such as iPads and Androids. The other most
commonly used mode, (Mode 1), is for the generic use of page
turning on the PC or MAC.
To change to the PC or MAC mode, (Mode1), turn off the BT-
105. Then, holding down the footswitch plugged into Port 1-2
(the jack closest to the red switch), turn on the BT-105.
Release both the footswitch and power switch as soon as you
see the LED blink. The LED will then blink red, then green,
then red, indicating the mode has been set.
Power Ports 1&2 LED Ports 3&4 USB

7
To change the mode back to the iPad mode, repeat the same
procedure using the footswitch in Port 3-4 (the jack closest to
the USB port). Keep the switch depressed until you see the
first blink, then release the footswitch and power switch. You
will then see one red blink, then 3 green blinks, then one final
red blink. The following table shows each mode and respective
signals:
Mode 1 set using switch 1 on startup (PC/MAC Mode)
Port 1 PgUp Port 3 PgDn
Port 2 Left Arrow Port 4 Right Arrow
Mode 2 set using switch 1 and 3 held together
Port 1 1 Port 3 3
Port 2 2 Port 4 4
Mode 3 set using switch 3 held on startup (Default Setting
– “iPad Mode”)
Port 1 Up Arrow Port 3 Dn Arrow
(Prev Page) (Next Page)
Port 2 Left Arrow Port 4 Right Arrow
Mode 4 set using switch 2 held on startup (cable splitter
required)
Port 1 ~1 Port 3 ~3
Port 2 ~2 Port 4 ~4

8
iOS Virtual Ke board
Some applications require the use of the keyboard to enter text
or to interact with the application. Since the BT-105 is an
external keyboard, the iPad or other iOS device by default
disables its own virtual keyboard.
To open the virtual keyboard, open any text box on the iPad,
then tap in the text box to activate the cursor. Then quickly
press and release the power switch while the BT-105 is
connected to the iPad. If you close the virtual keyboard from
within the application, you can press the power switch again to
reactivate it.. This is a toggle switch so pressing it will toggle
the virtual keyboard on and off. Note that iPhones may require
toggling on the keyboard for each use.
Charging
Please charge your BT-105 1-2 hours using the mini-USB to
USB charging cable and any USB wall power adapter, or 6
hours connected to your computer. Note some portable
computers may not sufficiently charge the BT-105. Disabling
the sleep setting on the computer may improve charging
performance.
Your BT-105 should last 100 hours or many days on a charge
depending on how much you use it. On a full charge, the LED
will blink green. When the power is low, the LED will blink as
follows:
Yellow every second = under 25% power
Red every second = under 10% power

9
If the BT-105 is turned off while charging, the LED indicator will
not light up, but it will still charge. If you leave the BT-105 on
while it is charging, the LED will remain lit and you can monitor
the charging status. Red is a low charge, solid yellow is a 75%
charge and orange/green is a full charge.
Note: If you fail to charge your battery when it begins blinking
red, you risk running it down completely which may require a
replacement battery. Charge the BT-105 at least once per
month to maintain good battery health.
Compatible Switches
Most normally open (NO)
momentary switches will work well
with the BT-105. Please visit:
http://airturn.com/footswitches for a
list of compatible switches. Some
footswitches have a latch mode. Be
sure that the latch mode is turned
off and/or the momentary mode is turned on. Port 3-4 is used
to turn to the next page, and Port 1-2 is used to turn to the
previous page.
For best results use the AirTurn ATFS-2 footswitch or the Boss
FS-5U footswitch with AirTurn patch cables. Check the AirTurn
store or your dealer for cable adapters for other brands of
footswitches.
Two adapter cables are provided to work with most ¼” phone
jack-equipped switches.

10
Tongue and Bite Switches
Tongue and Bite Switches are also
available from AirTurn or your dealer for
special uses. They are
used the same way as
any other momentary
switch.
See the specific instructions included with
each switch.
Troubleshooting
The BT-105 is not connecting or pairing
1. Turn off the BT-105.
2. Delete the AirTurn device on your host computer. On an iOS
device, go to the Bluetooth settings, (Settings, General,
Bluetooth), and press the “I” in the circle next to the AirTurn
selection and then press the Forget this Device button, then
OK.
3. Turn off Bluetooth on the host device.
4. Turn on the BT-105. Wait 3 seconds. Then hold the power
button for 8 seconds until you see the LED light blink red/green
rapidly several times.
5. Turn on Bluetooth on the host device.
6. The BT-105 should appear after 5-10 seconds depending on
the host.
Autres manuels pour BT-105
1
Table des matières
Autres manuels AirTurn Émetteur-récepteur


















