Air Venturi ROVAIR Manuel de l'opérateur

User Instruction Manual

RovAir

4500 PSI Portable Air Compressor

AV-ROVAIR4500

Ver. 1, 1/23

Contents

Parts Included.............................................................3

Setting up your RovAir Compressor...........................4

Operation Instructions: 110V or 220V outlet............5-6

Operation Instruction: 12V Battery ..........................7-8

Output Air Filter Replacement ....................................9

Troubleshooting........................................................10

Warranty ................................................................... 11

YOU AND OTHERS WITH YOU SHOULD ALWAYS

WEAR SHOOTING GLASSES TO PROTECT YOUR

EYES. READ ALL INSTRUCTIONS BEFORE USING. BUYER AND USER HAVE THE

RESPONSIBILITY TO OBEY ALL LAWS ABOUT THE PURCHASE, USE AND OWNERSHIP

OF THIS AIRGUN.

DANGER

!DANGER OF EXPLOSION!

Overlled compressed air cylinder

Do NOT exceed maximum ll pressure of 200 bar/ 2900 psi at room temperature!

IMPORTANT

THIS AIRGUN IS INTENDED FOR USE BY THOSE

16 YEARS OF AGE OR OLDER.

WARNING:

DO NOT INHALE DUST FROM LEAD PROJECTILES

OR PUT THEM IN YOUR MOUTH. WASH HANDS

AFTER HANDLING LEAD. SOME BBs MAY CONTAIN LEAD, A CHEMICAL KNOWN

TO THE STATE OF CALIFORNIA TO CAUSE CANCER AND BIRTH DEFECTS

(OR OTHER REPRODUCTIVE HARM).

DO NOT OVERFILL AIR CYLINDERS OR AIR GUN

TANKS, AS THIS CAN CAUSE SERIOUS INJURY OR

DEATH. NEVER SET THE OUTPUT PRESSURE/AUTO SHUT OFF ABOVE 4500 PSI (310

BAR).

WARNING

Do NOT exceed maximum ll pressure of your cylinder at room temperature!

YOU AND OTHERS WITH YOU SHOULD

ALWAYS WEAR SAFETY GLASSES TO

PROTECT YOUR EYES. READ ALL INSTRUCTIONS BEFORE USING.

IMPORTANT

THIS PRODUCT IS MADE TO FILL PRE-CHARGED

PNEUMATIC (PCP) AIR RIFLES AND PISTOLS

DIRECTLY. THIS PRODUCT SHOULD NOT BE USED TO FILL STAND ALONE SCBA

OR SCUBA TANKS/CYLINDERS. FILLING SCBA OR SCUBA TANKS/CYLINDERS MAY

DAMAGE THE COMPRESSOR AND WILL VOID YOUR WARRANTY.

IMPORTANT

Parts Included

1. Male QD tting & test plug

2. Replacement burst disks

3. Spare O-ring

4. Replacement valve springs

5. Replacement seals

6. Jumper Cables

7. Replacement lters

9. 3-prong power cord (not pictured)

Dual Cooling Fans

Filter Housing

Breaker Reset

Pressure

Release Valve

Carry Handle

On/Off Switch

Male Quick

Disconnect

Ouput Fitting Power Plug-in for

Jumper Cables

3-Prong Connector

Safety Valve

Burst Disc

Female Quick

Disconnect Fitting

Start/Stop Button

Gauge

Setting up your RovAir Compressor

1) The cover must be removed. Before removing,

make sure the compressor is not connected to an

active electrical outlet. Start by removing each of

the 13 phillips head screws, with a phillips head

screwdriver turning them counter-clockwise (g. 1).

Once all screws are removed, lift the cover o󰀨 of

the unit.

2) Locate the adjustment window on the power

converter. (g. 2a) Using an allen key, move the

switch to the 220V position. (g. 2b)

3) Replace the cover on the unit, and reinstall the

13 phillips head screws (g. 3)

4) Attach the hose and output lter to the compressor

via the female quick disconnect tting. The end with

the lter should be closest to the compressor (see

image for proper conguration) - (g. 4).

5) Make sure the connection between the female

quick disconnect on the hose and the male

connection on the compressor are tight.

Your RovAir comes pre-set to operate from an 110V outlet. Should you

choose to use the unit with a 220V outlet, complete the following steps.

CAUTION:

Always check and make sure the

collar on the female quick disconnect is in the forward

position and secure on the male tting you are

connecting it to. It is recommended that you check the

connection by attempting to pull the female and male

ends apart while the collar on the female tting is in

the forward position.

1) Plug the power cord into the RovAir (g. 1). DO NOT plug

the three prong connector into an active wall outlet yet.

2) Plug the 110V three prong connector into your wall outlet

(g. 2). Once plugged in, the fan on the power converter will

turn on.

NOTE: If connecting to a 220V outlet, an outlet adapter will be necessary to

use the included power cord.

3) Set the desired ll pressure via the dial on the top of the

pressure gauge (g. 3).

4) Close the bleed/pressure release valve by turning it

clockwise until it is tight (g. 4).

5) Connect the output hose to the device you wish to ll via

the female quick disconnect tting (g. 5).

PLEASE NOTE: If you are lling a PCP airgun from empty, you may need to

cock the gun before starting the ll process. Consult the owner's manual of

your airgun for further instructions.

6) Once these steps are complete, move the ON/OFF

switch to the ON (AC) position. The compressor fans

will begin to run. (g. 6).

7) Make sure the connection between the female quick

disconnect on the hose and the male connection on the

compressor are tight.

Operation Instruction: 110V or 220V outlet

DO NOT OVERFILL AIR

CYLINDERS OR AIR GUN

TANKS, AS THIS CAN CAUSE SERIOUS INJURY OR DEATH.

NEVER SET THE OUTPUT PRESSURE/AUTO SHUT OFF

ABOVE 4500 PSI (310 BAR).

WARNING

CAUTION:

Always check and make sure the collar

on the female quick disconnect is in the forward position

and secure on the male tting you are connecting it to.

It is recommended that you check the connection by

attempting to pull the female and male ends apart while

the collar on the female tting is in the forward position.

CAUTION:

Always check and make sure the collar

on the female quick disconnect is in the forward position

and secure on the male tting you are connecting it to. It is

recommended that you check the connection by attempting

to pull the female and male ends apart while the collar on

the female tting is in the forward position.

Operation Instruction: 110V or 220V outlet

10b

9) Once the fans are running, depress the START/STOP

button to begin lling (g. 7).

Note: You can stop the ll process at any time by depressing the START/

STOP button. If you do stop the ll for any reason, you MUST bleed the

pressure in the line before resuming lling. If you DO NOT bleed the

pressure in the line and just depress the START/STOP button to resume

lling, the RovAir will automatically stop after a few seconds of running.

10) Once the pre-set ll pressure is reached, the

compressor will stop.

NOTE: The cooling fans will continue to run.

11) Release/Bleed the pressure in the system by turning

the pressure release/bleed screw counter-clockwise

(g. 8).

12) Once the pressure is released and the pressure

gauge on the compressor reads 0 PSI/BAR, disconnect

the hose from the lled device by pulling back the collar

on the female quick disconnect tting and at the same

time, pulling it o󰀨 of the male tting it was connected to

(g. 9).

13) To power down your RovAir, switch the ON/

OFF switch back to the OFF position (g.10a). The

compressor fans will turn o󰀨. Unplugging the three prong

connector (g.10b) from your 110V outlet will turn o󰀨 the

power converter fan.

CAUTION:

Air and/or liquid may be released at

high velocity from the bottom of the unit. Keep ngers/

hands/eyes clear from the bottom of the unit when

opening the pressure release/bleed screw.

10a

1) Using the included jumper cables, connect the red

clamp to the positive post on the battery. Then connect

the black clamp to the negative post on the battery (g. 1).

2) Connect the cables to the compressor by inserting the

yellow plug into the outlet on the compressor (g. 2).

3) Set the desired ll pressure via the dial on the top of

the pressure gauge (g. 3).

4) Close the bleed/pressure release valve by turning it

clockwise until it is tight (g. 4).

5) Connect the output hose to the device you wish to ll

via the female quick disconnect tting (g. 5).

Operation Instruction: 12V Battery

!CAUTION:

Always check and make sure

the collar on the female quick disconnect is in the

forward position and secure on the male tting you are

connecting it to. It is recommended that you check the

connection by attempting to pull the female and male

ends apart while the collar on the female tting is in the

forward position.

PLEASE NOTE: If you are lling a PCP airgun from empty, you may need to cock the gun before

starting the ll process. Consult the owner's manual of your rie for further instructions.

DO NOT OVERFILL AIR

CYLINDERS OR AIR GUN

TANKS, AS THIS CAN CAUSE SERIOUS INJURY OR

DEATH. NEVER SET THE OUTPUT PRESSURE/AUTO

SHUT OFF ABOVE 4500 PSI (310 BAR).

WARNING

10b

Operation Instruction: 12V Battery

6) Once these steps are complete, move the ON/OFF

switch to the ON (DC12V) position (g. 6). The

compressor fans will begin to run.

7) Once the fans are running, depress the START/STOP

button to begin lling (g. 7).

Note: You can stop the ll process at any time by depressing the START/

STOP button. If you do stop the ll for any reason, you MUST bleed the

pressure in the line before resuming lling. If you DO NOT bleed the

pressure in the line and just depress the START/STOP button to resume

lling, the Nomad will automatically stop after a few seconds of running.

8) Once the pre-set ll pressure is reached, the

compressor will stop.

NOTE: The cooling fans will continue to run.

9) Release/Bleed the pressure in the system by turning

the pressure release/bleed screw counter-clockwise

(g. 8).

10) Once the pressure is released and the pressure

gauge on the compressor reads 0 PSI/BAR, disconnect

the hose from the lled device by pulling back the collar

on the female quick disconnect tting and at the same

time, pulling it o󰀨 of the male tting it was connected to

(g. 9).

11) To power down your RovAir, switch the ON/OFF

switch back to the OFF position (g.10a). The

compressor fans will turn o󰀨. Unplugging the yellow

connector (g. 10b) from your RovAir will turn o󰀨 the

power converter fan.

CAUTION:

Air and/or liquid may be released at

high velocity from the bottom of the unit. Keep ngers/

hands/eyes clear from the bottom of the unit when

opening the pressure release/bleed screw.

10a

Output Air Filter Replacement

1) Remove the lter and hose assembly from the

compressor unit by pulling back the collar on the female

quick disconnect tting and pulling the lter away from

the compressor (g. 1).

2) Find the seam in the lter housing (g. 2.1), twist the

large half counter-clockwise, unscrewing it until the unit

separates (g. 2.2).

3) Locate the cartridge lter inside of the large half of

the lter housing (g 3.1). Remove it with tweezers or by

puncturing it with an allen key and pulling it out of the

housing (g. 3.2).

4) Once the used lter is removed, replace it with a new

cartridge lter by pressing the new lter into the large

half of the housing (g. 4).

5) Reassemble the lter housing by screwing the small

and large halves together, turning the large half

clockwise until it is hand tight (g. 5).

6) Re-attach the female quick disconnect to the

compressor by pulling back on the collar on the female

while pressing it onto the male tting. Make sure the

collar is in the forward/locked position before attempting

to run the compressor.

2.2

3.1

3.2

2.1

NOTE: It is recommended that you replace the Air Filter every 2-3 hours of use.

Should you require extra Air Filters, they can be purchased through Air Venturi

authorized retailers.

Troubleshooting

Issue - Burst disc failure

- Resolution: Should the burst disc fail

during use of the compressor, depress

the ON/OFF button and make sure the

compressor has stopped. Open the

Pressure Release Valve to let the

remaining air vent from the compressor.

Once you have veried the burst disc

has failed (there will be a hole in it) by

removing the burst disc retention screw

(pictured right), remove the broken burst

disc from the unit. You will nd

additional burst discs in the bag of spare

parts that comes with the compressor.

Install a new burst disc, and re-insert

the burst disc retention screw by turning

clockwise. If you do not have additional

burst discs, contact Air Venturi for

replacement at: 216-220-1180.

In the unlikely event that your compressor malfunctions, DO NOT ATTEMPT

TO FIX THE PROBLEM YOURSELF. Please call Air Venturi’s service line so we

can address any issues or have you return the compressor for repair. Air

Venturi Service Line: 216-220-1180

Issue - Compressor will not start

- Resolution: Make sure the compressor is plugged into a functional electrical

outlet, and verify the plug into the wall and compressor are both properly

connected.

Issue - Compressor is not building pressure

- Resolution: Make sure the pressure release valve is closed. It should be hand

tightened. If closed and the compressor is still not building pressure, contact

Air Venturi by calling: 216-220-1180.

Issue - Compressor shuts o󰀨 within 10 seconds of starting a ll

- Resolution: Start the ll with the bleed valve open, once the compressor has run

for a few seconds, close the bleed valve and your compressor should run normally.

If this does not resolve the issue, contact Air Venturi by calling: 216-220-1180.

Issue - Compressor shuts o󰀨 before reaching desired pressure.

- Resolution: Make sure the Output Pressure Dial (Auto Shut O) is set properly.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Air Venturi Compresseur d'air

Air Venturi

Air Venturi Nomad II Manuel de l'opérateur

Manuels Compresseur d'air populaires d'autres marques

Sparmax

Sparmax DC-25XR Manuel utilisateur

KAESER

KAESER M122 Manuel utilisateur

GMC

GMC GAC1500 Manuel utilisateur

Briggs & Stratton

Briggs & Stratton Air Compressor Manuel utilisateur

Fini

Fini F3GST2TK Manuel utilisateur

Industrial Air

Industrial Air CP1580325 Manuel de programmation

Campbell Hausfeld

Campbell Hausfeld RP3300 Guide de démarrage rapide

Ingersoll-Rand

Ingersoll-Rand UP6 20 HP Manuel utilisateur

Hitachi

Hitachi EC99S Manuel de l'opérateur

Parkside

Parkside PKO 270 A1 Manuel utilisateur

Sullair

Sullair 185 Manuel utilisateur

Clas Ohlson

Clas Ohlson QIE-ZTH-15 Manuel utilisateur

Ferm

Ferm CRM1046 Manuel utilisateur

BE AC153 Manuel utilisateur

RIDGID

RIDGID OF25150A Manuel utilisateur

Johnson Controls

Johnson Controls QUANTUM LX Manuel

Sears

Sears Craftsman 919.167463 Manuel utilisateur

Ring Automotive

Ring Automotive RAC700 Manuel utilisateur