Air TEc Expert CYPRES 2 Manuel utilisateur
1000/35 A 1500/35 A
1900/35 A 2500/35 A
1000/35 indicates that this unit is set to
activate at approximately 1000 ft above
the DZ if the vertical speed is faster than
approximately 35 meters / second
~ 78 mph)
1500/35 indicates that this unit is set to
activate at approximately 1500 ft above
the DZ if the vertical speed is faster than
approximately 35 meters / second
~ 78 mph)
1900/35 indicates that this unit is set to
activate at approximately 1900 ft above
the DZ if the vertical speed is faster than
approximately 35 meters / second
~ 78 mph)
2500/35 indicates that this unit is set to
activate at approximately 2500 ft above
the DZ if the vertical speed is faster than
approximately 35 meters / second
~ 78 mph)
The
A
indicates that all CYPRES work with absolute pressure
The military CYPRES is available in the following
standard models:
All models can be adapted with a one or two-pin
cutter.
The Military CYPRES
Quick Guide For Operators
Airtec GmbH & Co. KG Safety Systems issue 2017-10 Art.No.:14133030 1
For further information's or questions please contact
military@cypres.cc
2500/29 A Changeable MODE
active BDZ Below DropZone)
Activation altitude down to MSL
2500/29 indicates that this unit is set to
activate at approximately 2500 ft above
the DZ if the vertical speed is faster than
approximately 29 meters / second
~ 65 mph)
Activation altitude
according to each Mode
Available for all military models
but on request only
This feature increases the chance of
unwanted activation's inside the airplane
The
A
indicates that all CYPRES work with absolute pressure
The military CYPRES is available in the following
standard models:
All models can be adapted with a one or two-pin
cutter.
The Military CYPRES
Quick Guide For Operators
Airtec GmbH & Co. KG Safety Systems issue 2017-10 Art.No.:14133030 2
For further information's or questions please contact
military@cypres.cc
Training Mode
2 Application Modes
Operation Mode
The feature of the civilian
CYPRES properties were
adapted to the various military
models. The activation altitude
and speed criteria are based
on the military model. see
reference data in the user's
guide). While on the ground it
takes care of all meteorologic
pressure changes during the
next 14 hours.
Useful if you are doing training
jumps, when Take OFF and
landing Target DZ) will be at
the sa e location / elevation.
Flight counter available on
Training Mode flights only.
The unit can be set to every
DZ on this globe, whether it is
the Dead Sea or the Himalaya
or even to a higher virtual DZ
e.g. HAHO jump.
It is possible to do the
programming prior to Take-
OFF, during flight and even
inside an active pressurized
cabin.
Just enter the absolute air
pressure value hPa) of your
Target DZ into the control unit
display.
No flight counter available in
Operation Mode.
HAHO
HALO
Take OFF / Landing Take OFF
Landing
Training Mode
Operation Mode
Airtec GmbH & Co. KG Safety Systems issue 2017-10 Art.No.:14133030 3
Quick Guide
- General Guidance -
click the button (a short press and release)
hold the button (keep the button pressed)
release the button
LED flash
LED ON
LED OFF
Explanation of the symbols / icons in this
Quick Guide
next indication / action
indication sequence ends with
continues from „10“ to „0“
e.g. calculation examples in blue
How to use the
quick guide
Airtec GmbH & Co. KG Safety Systems issue 2017-10 Art.No.:14133030 4
Switch ON
Training Mode
ambient air-pressure at
actual / current location
SWITCH OFF
sa e procedure
self test calibration 10 → 0
self test OK
unit switched ON
**
Switch ON
Airtec GmbH & Co. KG Safety Systems issue 2017-10 Art.No.:14133030 5
IMPORTANT: watch the complete „count down“ until you see 0▼
Additional information possible between “1” and “0▼“
displayed on page 15 + 16)
**
*
*
1) flight counter
2) serial number
3) next maintenance
4) revision number
5) mode setting
on changeable Mode only)
Unit Infor ation
switch ON
Unit
Infor ation
Airtec GmbH & Co. KG Safety Systems issue 2017-10 Art.No.:14133030 6
10 15 19 25
self test calibration 10 → 0
- right when 0▼ appears,
quickly press the button and keep it
pressed
- you will see a series of information
about your CYPRES see „Unit
information“)
- wait until the bar shows the actual
mode setting 10 / 15 / 19 / 25)
- let the button go and press again
quickly and keep it pressed
- CYPRES turns ON the LED
- when the LED is OFF immediately lift
your finger
- the setting will cycle through all possible
mode´s 10 / 15 / 19 / 25)
- click your new choice
then the CYPRES will switch itself OFF.
the change is not completed yet!
you have to repeat the entire procedure
once more to complete and fix the mode
change.
Changing the Mode
1000 / 1500 / 1900 / 2500
switch ON in
“Training Mode“
How to
change the Mode
Airtec GmbH & Co. KG Safety Systems issue 2017-10 Art.No.:14133030 7
10 15 19 25
10 15 19 25
immediately !
10 15 19 25
on the 4th click hold the button
switch ON
continued on next page
**
Switch ON
Operation Mode
“Entering hPa of Target DZ“ (Exa ple 893 hPa)
Additional information possible between “1” and “0”
displayed on the last 2 pages)
**
appears immediately
the first left digit 1 alternates
with 0
at the chosen number *
release the button
hold the button again
self test calibration 10 → 0
ambient air-pressure at
actual / current location
Switch ON
Operation Mode
Airtec GmbH & Co. KG Safety Systems issue 2017-10 Art.No.:14133030 8
hold the button again
the third digit counts 0 - 9
at the chosen number *
release the button
hold the button again
the fourth digit counts 0 - 9
at the chosen number *
release the button
unit switched ON
set hPa will stay visible
* if you missed the correct number, just
keep holding the button
until the number appears again.
x 4 seconds *** confir ation of setting
continued from previous page
Switch ON
Operation Mode
“Entering hPa of Target DZ“ (Exa ple 893 hPa)
the second digit counts 0-9
at the chosen number *
release the button
Switch ON
Operation Mode cont.
*** during this 4 seconds it is possible
to restart setting procedure by
holding the button
Airtec GmbH & Co. KG Safety Systems issue 2017-10 Art.No.:14133030 9
METHOD 1 --> if:
Operation Mode
Using The Military Calculator
If absolute air-pressure
(hPa) of Target DZ
is not available
- Target Dz and Take Off area are local
but at different elevations
- Take Off elevation is available
- Target DZ elevation is available
switch ON
enter a bient ground pressure
QFE) switch ON hPa value)
e.g.
press hPa
press + if target is higher)
press – if target is lower)
enter difference in feet meters)
between Take OFF location and
Target DZ. e.g.
press „feet“ meters)
display shows hPa of Target DZ
enter value into the
Military CYPRES
Military
Calculator
Airtec GmbH & Co. KG Safety Systems issue 2017-10 Art.No.:14133030 10
Autres manuels pour Expert CYPRES 2
6
Table des matières
