Air Lift Performance 3H Manuel utilisateur
PATENTED
Air Lift
Performance
3H /3P
™
Control System
For maximum effectiveness and safety,
please read these instructions completely
before operating.
Failure to read these instructions can result in an
incorrect installation.
USER GUIDE
MN-948 • (041808) • ECR 9097
PATENTED
Download the App for
the Best #lifeonair
The Air Lift Performance 3 mobile app allows
for full integration of your new 3H/3P control
system on compatible mobile devices. Simply
download the FREE app to not only take full
control of your system, but to always have the
latest system firmware with updates directly
from the app.
For iPhone: air-lift.co/3app
For Android: air-lift.co/android
Users can also search “Air Lift Performance”
in either the Apple App Store or Google Play.
See page 9 for instructions on pairing your
device.
TABLE OF CONTENTS
Introduction .................................... 4
Important Safety Notices ....................................4
Main Controls ....................................5
Quick Reference Guide.............................6
Getting Started ...................................7
Display ..........................................8
Operation ........................................9
Setup ..........................................10
Calibration ......................................12
Calibration Detail Explained........................14
Firmware Updates................................16
Additional Information ............................18
About ..........................................19
System Messages ................................20
Integrated Diagnostics .....................................22
VIAIR Duty Cycle/Working Pressure .................23
4MN-948
3H/3P User Guide
Introduction
The purpose of this publication is to assist with the calibration,
maintenance, and troubleshooting of the Air Lift Performance 3P or 3H
control systems.
Read the entire user guide before beginning calibration or performing
any maintenance, service or repair. The information includes a step-by-
step calibration set-up, display options and functions, and diagnostic
troubleshooting.
Air Lift Company reserves the right to make changes and improvements to
its Air Lift Performance products and publications at any time. For the latest
version of this User Guide, contact Air Lift Company at (800) 248-0892 or
visit www.airliftperformance.com.
IMPORTANT SAFETY NOTICES
BEFORE SERVICING THE VEHICLE, MAKE SURE TO TURN
OFF “RISE ON START” AND “PRESET MAINTAIN.” THIS WILL
ELIMINATE ANY UNINTENDED SUSPENSION CYCLING IF YOU
NEED TO TURN THE KEY ON IN THE VEHICLE FOR ANY REASON.
ONLY USE THE AIR LIFT PERFORMANCE 3 APP ON A MOBILE
DEVICE WHEN THE VEHICLE IS IN A CLEAR LINE OF SIGHT. TO
AVOID THE RISK OF SERIOUS INJURY OR HARM, VERIFY THAT
NO PERSON OR THING IS NEAR OR IN THE WAY OF THE VEHICLE’S PATH OF TRAVEL WHILE
CYCLING THE SUSPENSION.
FOR USER SAFETY AND TO PREVENT VEHICLE DAMAGE,
THE SYSTEM HAS A 25% OR 25 PSI (1.7BAR) MINIMUM
DRIVE HEIGHT AS THE DEFAULT. DUE TO EXTREME RISK OF
DANGER TO THE USER OR VEHICLE, AIR LIFT COMPANY STRONGLY RECOMMENDS
NOT TO CHANGE THIS VALUE. IF FOR SOME REASON THE MINIMUM DRIVE HEIGHT IS
SET BELOW THE DEFAULT VALUE, AIR LIFT COMPANY SUGGESTS THIS SETTING ONLY
BE USED WHILE THE VEHICLE IS STATIONARY. IT IS POSSIBLE TO SET THE VEHICLE AT A
HEIGHT THAT IS BELOW THIS THRESHOLD, THEN START DRIVING. THIS IS A UNIVERSAL
SYSTEM AND SETTINGS WILL BE DIFFERENT FOR EVERY USER AND VEHICLE. THE
INSTALLER IS RESPONSIBLE TO DETERMINE HOW LOW THE SUSPENSION CAN BE SET
WITHOUT CAUSING DAMAGE. IT IS THE SOLE RESPONSIBILITY OF THE USER, AND AIR
LIFT COMPANY WILL NOT BE HELD LIABLE FOR, ANYTHING THAT MAY HAPPEN TO THE
OPERATOR OR THE VEHICLE AS A RESULT OF THE USER’S CHOICE TO ALTER THESE
DEFAULT VALUES BELOW RECOMMENDED MINIMUMS.
FLOOR JACKS CAN BE DANGEROUS. WHENEVER USING
A FLOOR JACK, MAKE SURE IT IS RATED FOR THE LOAD IT
IS LIFTING. CHECK THE VEHICLE OWNER’S MANUAL FOR
INFORMATION ABOUT WHERE TO PLACE THE JACK. BEFORE RAISING THE VEHICLE,
PLACE WHEEL CHOCKS IN FRONT AND BEHIND THE WHEELS TO PREVENT THEM FROM
ROLLING. ALWAYS USE JACK STANDS TO SUPPORT THE VEHICLE. NEVER GET UNDER OR
PLACE ANY BODY PARTS UNDER A VEHICLE THAT IS SOLELY SUPPORTED BY THE JACK.
WARNING
WARNING
WARNING
WARNING
5
MN-948
3H/3P User Guide
Front Left Bag
Pressure
Rear Left Bag
Pressure
Mode Indicator
Tank pressure
Front Right Bag
Pressure
Rear Right Bag
Pressure
User-defined
Button
(See Page 7
All-Up Button)
Manually increase
and decrease front
right bag pressure.
Manually increase
and decrease front
left bag pressure.
Manually increase
and decrease rear
right bag pressure.
Manually increase
and decrease rear
left bag pressure.
Preset High
(Up Button)
Preset Ride
(Middle Button)
User-defined
Button
(See Page 7
All-Down Button)
Preset Low
(Down Button)
Main Controls
System Messages
Fault Indicator
6MN-948
3H/3P User Guide
Quick Reference Guide
Main Menu
Screen Sub-Menu Data Default
Display
Brightness Level 1-10 Level 7
Brightness Sleeping Level 1-10 Level 4
Sleep Time 5-60 Sec 10 Sec
All-Up Button
All-Up
All Up
Front-Up
Rear-Up
All-Down Button
All-Down
All Down
Front-Down
Rear-Down
Units PSI PSI
BAR
Operation
Rise-on-Start Off Off
On
Pre-Set Maintain Off Off
On
Minimum Drive Height 0-100 PSI (Pressure)
0-100% (Height) 25 PSI / 25%
Pressure/Height Mode Height Pressure
Pressure
Anti Cross-Load (Height)
Axle Equalization
(Pressure)
Off
On
On
Show Mode Off Off
On
Bluetooth Pairing Off Off
On
Setup
Sensor Tool See Page 10 —
Compressor See Compressor
Main Menu —
Min. Battery (Voltage
to allow compressor
to still run)
10-15 Volts 11 Volts
Factory Reset Cancel Cancel
Reset All
Compressor
On/Off Off Off
On
Enable/Disable Enabled Enabled
Disabled
Dual/Single Single Single
Dual
Max Pressure 150-200 PSI
(10342-13789mBAR) 150 PSI (10342mBAR)
Duty Cycle
33%
50%
50%
66%
75%
100%
Calibration Wizard See Page 12 —
7
MN-948
3H/3P User Guide
Getting Started
This User Guide is designed to demonstrate
all the different menu options and default
settings that will help make using this
system easy and enjoyable.
1. To get to the main menu screen,
push the middle (preset ride) button
simultaneously with either the up (preset
high) button or down (preset low)
button.
2. All other settings
and parameters will
be detailed in the
following pages to
ensure the system is
set up accurately.
3. Use the preset low
and preset high
buttons to scroll.
4. Green text indicates the last saved
value.
User-defined button
Preset high (up)
Preset ride (middle)
Preset low (down)
User-defined button
8MN-948
3H/3P User Guide
Display
BRIGHTNESS
Set the brightness for the display while in use.
1. Level 1-10
2. Use the up and down buttons
to increase or decrease luminosity
in 10% increments.
3. Level 7 (default)
BRIGHTNESS SLEEPING
Set the brightness for the display after it goes
into sleep mode.
1. Level 1-10
2. Use the up and down buttons to
increase or decrease luminosity
in 10% increments.
3. Level 4 (default)
SLEEP TIME
Set the amount of time it takes to revert back
to the main screen and for the display to go to
sleep.
1. 5-60 seconds.
2. Use the up and down buttons to increase or
decrease time in 1-second increments.
3. 10 seconds (default)
ALL-UP BUTTON
Set function for the all-up button.
1. All-up (default)
2. Front-up
3. Preset
ALL-DOWN BUTTON
Set function for the all-down button.
1. All-down 3. Preset
2. Front-down 4. Air-out (default)
UNITS
Set units of measure to PSI or BAR.
1. PSI (default)
2. BAR
9
MN-948
3H/3P User Guide
RISE-ON-START
This setting brings the vehicle to ride height
at key-on if below ride height.
1. Off (default)
2. On
PRESET MAINTAIN
When enabled, the Preset Maintain will maintain
the selected preset, whether pressure or height.
1. Off (default)
2. On
MINIMUM DRIVING HEIGHT
Set the minimum vehicle ride height. The system
will not deflate below this level while driving.
1. 0-100 PSI (pressure mode) or 0-100%
(height mode)
2. Hold down the up or down button to cycle
quickly to 0 or 100 PSI or press the buttons individually to go up or
down 1 PSI at a time.
3. 25 PSI (pressure mode) or 25% (height mode) (default)
PRESSURE/HEIGHT MODE
Set system to operate in height or pressure mode.
1. Height
2. Pressure (default)
ANTI CROSS-LOAD/AXLE EQUALIZATION
Set system to equalize the axle to prevent cross-loading.
1. Off
2. On (default)
SHOW MODE
This provides operation with ignition off for one ignition cycle.
(Running the compressor(s) will drain the battery.)
1. Off (default)
2. On
BLUETOOTH PAIRING
Set to “on,” to enable Bluetooth pairing with a compatible mobile device
for one ignition cycle. If no display is present, pairing mode can be entered
by: turning the ignition on 3 seconds, ignition off 3 seconds, ignition on.
Operation
10 MN-948
3H/3P User Guide
Setup
SENSOR TOOL (HEIGHT MODE
MUST BE ENABLED)
This tool is used to ensure that the range of
the height sensors as installed are sufficient
to provide optimal accuracy for the system.
(Each time that this tool is used it will reset and
initially show low range until the suspension is
cycled to tell the system its range.)
1. At any time, press the “Preset Ride”
button to exit the tool.
2. By cycling the suspension up and down,
the tool will determine the following:
•Range low – Not enough range in the
sensor to portray accurate data.
•OK – The range of the sensor is
adequate for accurate data.
•Limit – The range of the sensor is at
or beyond the bounds of acceptable
data.
3. The “Preset Low” button can be used to
reset the tool.
COMPRESSOR* (SETUP)
ON/OFF
Control the compressor(s) manually. In the
default setting of “Off” the compressor(s) will
operate normally. Selecting “On” will activate
the compressor(s) for troubleshooting.
1. Off (default)
2. On
ENABLE/DISABLE
Enable or disable the compressor(s) until the
next ignition cycle.
1. Enabled (default)
2. Disabled
* The 3H/3P system can be installed with one or two compressors.
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Air Lift Performance Système de contrôle
