Aiphone IX-DVF-10KP Guide d'installation
1
IX-DVF-10KP
The IX-DVF-10KP is an IX Series video door station with a combination keypad and proximity card reader.
The IX-DVF-10KP will connect to a network switch, and the built-in keypad connects to an access control
system with a Wiegand connector.
INSTALLATION AND PROGRAMMING GUIDE
1
2
3
4
5
IX-DVF-10KP
• IP video door station
• Proximity card reader and access keypad
• Stainless steel faceplate with tamper resistant screws
Features
1. Camera
2. Microphone
3. White LED for night viewing
4. Speaker
5. Call button
6. Proximity card reader and keypad
Names and Functions
PACKAGE CONTENTS
For ush mounting, recess the supplied back box into
the wall, then attach the mounting bracket using the four
provided screws.
For surface mounting, use the SBX-IXGDM7 surface
mount box. This box can mount to a standard
single‑gang box or to any at surface.
Use the two standos to install the security screws.
These are required for both the included back box and
the SBX-IXGMD7 surface mount box.
Back Box Dimensions: 12-1/2" H x 6-1/8" W x 2-3/8" D
IX-DVF-10KP Dimensions: 13-11/16" H x 7-3/16" W
Installation
6
2 Security Screws
4 Bracket Screws
Door Release
Wire Harness
Accessories included
Installation Manual
(this manual) x1
Option connector
x1
T20 screwdriver
bit x1
Chinese RoHS paper
x1
Special Screw
x4 Back Box
x1
IX-DVF-10KP
Door Station
Flush Mount Back Box and
Mounting Bracket
2 Security Screw
Standos
Security Driver
Keypad Instructions
2
FCC WARNING:
This device complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference that may cause undesired operation.
• For proper regulatory compliance, the drain wire should be disconnected at the power supply end of the cable.
• Changes or modications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
Specications
Door Station:
Camera unit: 1/3" color CMOS 1.23 megapixel
Min. illumination: 5 Lux
Terminations: RJ45
Operating Temp: -31° ~ 140°F / -35° ~ 60°C
Wiring Distance: 328' with Cat-5e/6 cable to switch
Dimensions: 13-11/16" H x 7-3/16" W
w/ SBX-IXGDM7: 13-3/4" H x 7-5/16" W x 3-1/16" D
Proximity Reader w/ Access Keypad
Supported
Credentials: Aiphone 40-bit, HID, AWID, Pyramid
Wiring: Wiegand Connection
PoE Switch
Cat-5e / Cat-6
IX-DVF-10KP
IX-MV7 IX-MV7
Wiring Diagram
Access
Control Host
3
Getting Started
This programming guide will cover how to program an IX-DVF-10KP door station and IX-MV7 master stations using the IX Support
Tool software. For additional information and documentation for the IX system, please visit www.aiphone.com/ix.
Programming instructions for the keypad are included separately. If the keypad is being used in conjunction with Aiphone’s
AC Series access control system, please visit www.aiphone.com/ac for more information.
Support Tool will open in Table View on the Station Information, Identication page. Enter unique Station Numbers and
Names for each station. Click
Update
to save the changes.
Station Information
Open the IX Support Tool, then select File from the top menu and click Create New System. Enter in a System Name, and select
the No radial button for Wizard Programming. Enter a system ID and Password. Enter station quantities and then click
Finish
.
Creating a New System
The IX-DVF-10KP counts
as an IX-DV, IX-DVF(-*)
station in this section.
6
2
New System Name
SomeUserName
SomePassword
Some versions of IX
Support Tool will have
a Save button in place
of the Update button.
4
The IP addresses for the stations can be individually set for each station or they can be congured in a batch. This guide will show how
to assign via the batch conguration. Navigate to Network Settings, IP Address, then click on
Batch IP Address Conguration
Network Settings - IP Address
On the Batch IP Address Conguration page, enter a starting IP address and subnet mask. Check the box beside each station or
click
Select
to check all stations at once. Click
OK
, then click
OK
on the conrmation pop‑up. Each station will now have an
IP address and Subnet Mask assigned to it.
Batch IP Address Conguration
If a Default Gateway
address is required, it can
be manually added on this
page once the IP addresses
have been assigned.
5
The station name and IP address that were assigned in the previous steps will now need to be associated to each station in the
system before any call settings can be uploaded. From the top menu bar, navigate to Tools(T), Association Settings.
Association Settings
When the Association Settings window opens, it will automatically begin searching for any IX stations on the network. Once
this is complete, select a conguration in the Station Settings List at the top, then select the station to assign it to in the Station
List. Click
Apply
and
OK
on the pop-up to start the association process for that station, then repeat these steps for the
remaining stations.
Once associated, the stations will restart with the IP address and station name assigned. Scroll down to the Associated Stations
List at the bottom of the page to conrm the status of the association.
If the Station Search fails to
nd any stations, verify that
the stations are powered on
and that the PC is connected
to the same switch.
6
The IX-DVF-10KP’s call button is wired to Option Input 1. This input will need to be programmed to place a call. Click
Station View
,
then navigate to Option Input/Relay Output Settings, Option Input.
Call Button Settings - Option Inputs
Option Inputs
In the Select Station to Edit menu, use the Number drop-down to select the IX-DVF-10KP, then click
Select
. Use the
Option Input drop-down to select Option Input 1. Click the Call radial button, then click
Update
.
Once the Option Input is set to call, a Called Station Group will be assigned to each to allow for selective calling from each button.
Navigate to Call Settings, Called Stations (Door/Sub Stations). Use the Group Number drop-down to select Group 01.
Called Stations Groups
By default, Group 01 will contain all master stations in the system. If these need to be changed, use the
Open
and
Delete
buttons to
add or remove master stations from the list. Once the call group is congured, click
Update
. If any other inputs are being congured
to place calls when activated by third party equipment, switch to the next group using the Group Number drop-down. Repeat these
steps to congure these call groups.
7
Once all settings are congured, select File (F) from the top bar and select Upload Settings to Station.Click
Select
to check all of
the stations, then click on
Settings
. Once
OK
is pressed on the conrmation pop‑up, the upload process will start. This process will
take around 30 seconds to a minute. Once it is complete, conrm that the Status column shows Success for each station.
Setting File Upload
For more details about the features and information above, please contact Technical Support.
Aiphone Corporation | www.aiphone.com | (800) 692-0200
02/24
To link the Called Stations groups to the call button on the door station, navigate to Call Settings, Call Origination. Use the
Call Button / Option Input # drop-down and select Option Input 1.
Programming the Call Button
Use the Standard Mode Settings, Call Destination drop-down to assign a call group to the Option Input. Click
Update
. If any other
option inputs are being used for calling, switch to the next Option Input and repeat these steps as necessary.
Table des matières
Autres manuels Aiphone Système d'interphone
Aiphone
Aiphone AT-306 Manuel utilisateur
Aiphone
Aiphone GT-1M-L Manuel utilisateur
Aiphone
Aiphone IS-SS-RA Manuel utilisateur
Aiphone
Aiphone RCX-48CEU/B Manuel utilisateur
Aiphone
Aiphone LAF-C CONSOLE MASTER LAF-20C Manuel utilisateur
Aiphone
Aiphone IB-DA Manuel utilisateur
Aiphone
Aiphone IP-EWST Manuel
Aiphone
Aiphone IC-DC Manuel utilisateur
Aiphone
Aiphone MK-DVF-HID Manuel utilisateur
Aiphone
Aiphone GT-2C Manuel utilisateur
Aiphone
Aiphone LC-10S Manuel utilisateur
Aiphone
Aiphone IXG System Manuel utilisateur
Aiphone
Aiphone JF-1FD Manuel utilisateur
Aiphone
Aiphone MB-D Manuel utilisateur
Aiphone
Aiphone TC-MB Manuel utilisateur
Aiphone
Aiphone DA-1MD Manuel utilisateur
Aiphone
Aiphone LEF-10C Manuel utilisateur
Aiphone
Aiphone LEF-3 Manuel utilisateur
Aiphone
Aiphone LAF-10B Manuel utilisateur
Aiphone
Aiphone JBS-2AD Manuel utilisateur
