AIC HA201-AP Manuel utilisateur

UM_HA201-AP_v.1_032717

HA201-AP

Storage Server Barebone

User's Manual

contents

CONTENTS

PREFACE��i

SAFETY INSTRUCTIONS�� ii

Chapter 1� Product Introduction �� 1

1�1 Box Content �� 1

1.2 Specications �� 2

1�3 General Information�� 3

Chapter 2� Hardware Installation�� 7

2�1 Removing and Installing top cover �� 7

2�2 System Memory�� 8

2�3 Removing and Installing the canister Top cover�� 11

2�4 Installing/ Removing a Solid State Drive �� 12

2�5 Removing and Installing a Fan Module �� 13

2�6 Removing/Installing a Drive Tray/ Hard Drive/ Drive Slot Map�� 14

2�7 Removing and Installing the HDD backplane Module�� 18

2�8 Removing and Installing the Power Supply �� 19

2�9 Removing and Installing the PCIe Card�� 20

2�10 Tool-less Blade Slide Installation introduction �� 22

Chapter 3� Motherboard Settings �� 26

3�1 Motherboard block diagram �� 26

3�2 Motherboard Layout �� 27

3�3 Motherboard Content List�� 28

3�4 Internal Connectors/Jumpers �� 29

3�5 LEDs�� 37

Chapter 4. BIOS Conguration and Settings�� 40

4�1 Method 1 (Use the BIOS setup) �� 40

4�2 Method 2 (Use a Dos tool - Syscheck)�� 43

4�3 BMC web-browser-MegaRAC® GUI Overview �� 45

4�4 Using MegaRAC SP-X�� 51

Chapter 5� Backplane Overview �� 53

contents

5�1 Backplane�� 53

Chapter 6� Technical Support �� 57

This document contains proprietary information about

AIC products and is not to be disclosed or used except in

accordance with applicable agreements.

PREFACE

• Copyright

No part of this publication may be reproduced, stored in a retrieval system,

or transmitted in any form or by any means, electronic, mechanical, photo-

static, recording or otherwise, without the prior written consent of the

manufacturer.

• Trademarks

All products and trade names used in this document are trademarks or

registered trademarks of their respective holders.

• Changes

The material in this document is for information purposes only and is subject

to change without notice.

• Warning

1. A shielded-type power cord is required in order to meet FCC emission

limits and also to prevent interference to the nearby radio and television

reception. It is essential that only the supplied power cord be used.

2. Use only shielded cables to connect I/O devices to this equipment.

3. You are cautioned that changes or modications not expressly approved

by the party responsible for compliance could void your authority to

operate the equipment.

• Disclaimer

AIC shall not be liable for technical or editorial errors or omissions

contained herein. The information provided is provided "as is" without

warranty of any kind. To the extent permitted by law, neither AIC or its

affiliates, subcontractors or suppliers will be liable for incidental, special or

consequential damages including downtime cost; lost profits; damages

relating to the procurement of substitute products or services; or damages

for loss of data, or software restoration. The information in this document is

subject to change without notice.

SAFETY INSTRUCTIONS

• Before getting started, please read the following important cautions:

• All cautions and warnings on the equipment or in the manuals should be

noted.

• Most electronic components are sensitive to electrical static discharge.

Therefore, be sure to ground yourself at all times when installing the

internal components.

• Use a grounding wrist strap and place all electronic components in

static-shielded devices. Grounding wrist straps can be purchased in any

electronic supply store.

• Be sure to turn off the power and then disconnect the power cords from

your system before performing any installation or servicing. A sudden

surge of power could damage sensitive electronic components.

• Do not open the system’s top cover. If opening the cover for

maintenance is a must, only a trained technician should do so.

Integrated circuits on computer boards are sensitive to static electricity.

Before handling a board or integrated circuit, touch an unpainted

portion of the system unit chassis for a few seconds. This will help to

discharge any static electricity on your body.

• Place this equipment on a stable surface when install. A drop or fall

could cause injury.

• Please keep this equipment away from humidity.

• Carefully mount the equipment into the rack, in such manner, that it

won’t be hazardous due to uneven mechanical loading.

• This equipment is to be installed for operation in an environment with

maximum ambient temperature below 35°C.

• The openings on the enclosure are for air convection to protect the

equipment from overheating. DO NOT COVER THE OPENINGS.

• Never pour any liquid into ventilation openings. This could cause re or

electrical shock.

• Make sure the voltage of the power source is within the specification

on the label when connecting the equipment to the power outlet. The

current load and output power of loads shall be within the specication.

• This equipment must be connected to reliable grounding before using.

Pay special attention to power supplied other than direct connections,

e.g. using of power strips.

iii

• Place the power cord out of the way of foot trafc. Do not place anything

over the power cord. The power cord must be rated for the product, voltage

and current marked on the product’s electrical ratings label. The voltage

and current rating of the cord should be greater than the voltage and

current rating marked on the product.

• If the equipment is not used for a long time, disconnect the equipment from

mains to avoid being damaged by transient over-voltage.

• Never open the equipment. For safety reasons, only qualified service

personnel should open the equipment.

• If one of the following situations arise, the equipment should be checked by

service personnel:

1. The power cord or plug is damaged.

2. Liquid has penetrated the equipment.

3. The equipment has been exposed to moisture.

4. The equipment does not work well or will not work according to its user

manual.

5. The equipment has been dropped and/or damaged.

6. The equipment has obvious signs of breakage.

7. Please disconnect this equipment from the AC outlet before cleaning.

Do not use liquid or detergent for cleaning. The use of a moisture sheet or

cloth is recommended for cleaning.

• Module and drive bays must not be empty! They must have a dummy cover.

Product features and specications are subject to change without notice.

CAUTION :

risk of explosion if battery is replaced by an incorrect type.

dispose of used batteries according to the instructions.

After performing any installation or servicing, make sure the

enclosure are lock and screw in position, turn on the power.

HA201-AP User's Manual

Chapter 1 Product Introduction

1�1 Box Content

Chapter 1� Product Introduction

Before removing the subsystem from the shipping carton, visually inspect the

physical condition of the shipping carton. Exterior damage to the shipping

carton may indicate that the contents of the carton are damaged. If any

damage is found, do not remove the components; contact the dealer where

the subsystem was purchased for further introduction. Before continuing, rst

unpack the subsystem and verify that the contents of the shipping carton are

all there and in good condition.

• Enclosure( Power supply, fan, 24 HDD tray included)

• RS232 cablex 1pcs • Power cord x 2sets • Screws kit x 1set

• Slide rail x 1set

If any items are missing, please contact your authorized reseller or sales representative.

HA201-AP User's Manual

Chapter 1 Product Introduction

1.2 Specications

Dimensions

(W x D x H)

(with chassis ears)

mm : 632 x 435 x 8 8

inches : 24.9 x 17.1 x 3.5

Motherboard

(per node) AIC Server Board Apollo

Processor

(per node)

Processor

Support

One Intel® Xeon® Processor D-1500 product

family

Socket Type SoC (System-on-a-Chip)

Chipset Support

(per node) SoC (System-on-a-Chip)

System Memory

(per node)

• 4 DIMM slots

Up to 128GB DDR4 2133/1866MHz ECC UDIMM

Front Panel System power on/off

LE Ds

A• Power (Primary)

• Warning

B• Power (Secondary)

• Warning

Drive Bays

External

3.5" hot swap 8

2.5" hot swap 8

Internal 2.5" 2

Backplane 1 x 16-port 12Gb SAS dual-loop backplane

Expansion Slots

(per node) PCIe 3.0 1 x8 FHHL

Riser Card

(included)

(per node)

RC-PE1U09-TY 1x PCIe X8

System BI OS

BIOS Type

• Insyde

• SPI (Serial Peripheral Interface)

FLASH Interface

BIOS

Features

• ACPI

• PXE

• WOL

• AC loss recovery

• IPMI 2.0 KCS interface

• SMBIOS

• Serial console redirection

• BIOS Boot Specification

• BIOS Recovery Mode

• SRIOV

• PCIe Hotplug

• iSCSI

• TPM

On-board

Devices

SATA

PCH on-chip solution supports 6 x SATA

6.0Gb (one of the SATAs shares with M.2

SATA interface)

1 x NGFF (M.2 B-key) slot supports PCI-e

Gen.2 x1/x2 & SATA co-design

IPMI Aspeed AST2400 Advanced PCIe Graphics &

Remote Management Processor

Network

Controllers

•2 x Springville_I210 Gigabit MAC/PHY

supports Giga LAN @Rear I/O

•2 x Springville_I210 Gigabit MAC/PHY

supports Giga LAN @AirMax

•2 x integrated Magnolia Park + Cortina

CS4227 PHY support dual ports 10G

SFP+

Graphics

Aspeed AST2400 Advanced PCIe Graphics &

Remote Management Processor

• PCIe VGA/2D Controller

• 1920x1200@60Hz 32bpp

Rear I/O

(per node)

LAN

2 x 10G SFP+ (double-stack)

2 x RJ45 GigaLAN (double-stack)

1 x RJ45 (BMC management port)

USB 2 x USB 3.0 Type A

VGA 1 x DB-15 (shares with onboard pin header)

Serial Port 1 x DB-9 COM1

Others 2 x mini-SAS HD (SFF-8644)

Power Supply 600W 1+1 redundant power supply

System Cooling

(per node) 3 x 40x56mm dual rotor fans

System

Management

• Baseboard Management Controller

• Intelligent Platform Interface 2.0 (IPMI 2.0)

• iKVM, Media Redirection, IPMI over LAN, Serial over LAN

• SMASH Support

Environmental

Specifications

• Temperature: 0°C - 35°C

• Humidity: 5% - 95% non-condensing

Gross Weight (w/ PSU & Rail)

kgs : 26

lbs : 57.3

Packaging

Dimensions (W x D x H)

mm : 965 x 590 x 330

inches : 40 x 23.2 x 13

Mounting Standard

HA201-AP User's Manual

Chapter 1 Product Introduction

1�3 General Information

HA201-AP, a 2U Storage Server Barebone, ach supporting one Intel®

Xeon-D® Processor and up to 128GB of DDR4 memory. HA201-AP has a

8 x 2.5” hot swap HDD bays as system drive bays. It is a perfect building

block for Storage Servers.

• Front Panel

8 x 2.5" hot swap drive bays

8 x 3.5" hot swap drive bays

• LED Indicator and Switch

Table des matières

Autres manuels AIC Serveur de stockage réseau

Manuels Serveur de stockage réseau populaires d'autres marques

HP NetStorage 6000 Manuel utilisateur

Seagate

Seagate U10 ST320423A Manuel utilisateur

Synology

Synology RackStation RS816 Manuel

D-Link

D-Link ShareCenter Pro DNS-1200-05 Manuel utilisateur

Avid Technology

Avid Technology VideoRAID ST Guide de sécurité

Western Digital

Western Digital My Cloud Home Duo Manuel utilisateur

PrimeArray

PrimeArray 4xxx Manuel utilisateur

Buffalo

Buffalo TeraStation WSS WSH5010N6 Manuel utilisateur

Planex

Planex MZK-NAS01SG Manuel utilisateur

Intel

Intel SS4000-E - Entry Storage System NAS Server Manuel utilisateur

Synology

Synology RS2212+ Manuel utilisateur

Allnet

Allnet ALL69000 Manuel utilisateur

Adaptec

Adaptec 5325301580 Manuel utilisateur

Motorola

Motorola EXORdisk II Manuel utilisateur

Sony

Sony XDAAI1PK Manuel utilisateur

Cisco

Cisco Linksys NAS200 Instructions d'utilisation d'origine

Sans Digital

Sans Digital MR4UT6G Manuel utilisateur

Dell

Dell PowerVault NX3500 Instructions d'utilisation