AGT AGT-BDRC48 Manuel utilisateur
1
S k i d S t e e r F r o n t M o u n t C u t t e r - A G T - B D R C 4 8
PRODUCT MANUAL
This equipment can not be installed, operated or
repaired without reading instructions.
Electricity must be hooked up by certified electrician.
Do not use this equipment beyond its rated capacity.
Missing parts or questions on assembly?
https://www.agrotkindustrial.com/
sales@agrotkindustrial.com https://www.agrotkindustrial.com/
WARNING
2
Directory
Product introduction.................. 1/17
Operator......................................2/17
Safety precautions.......................3/17
Technical parameters................. 4/17
Installation...................................7/17
Handing safety.............................10/17
Limited Warranty........................17/17
3
Production Introduction
1. AGT BDRC48 swing mower uses three oil cylinders to adjust the lifting
and side swing, It is an excellent choice for clearing pond banks and
cutting trails!
2. The blade of AGT BDRC48 brush cutter is made of boron steel. A range
of hydraulic flow of 12-16 gpm is required
3. The combination of motor and gear box is adopted, which is more
durable.
4. AGT provide you with a one-year warranty. If you have any problems,
we are able to support the after-sale service.
4
Operator
Congratulations on owning this 48'' Skid Steer Articulating Brush Cutter!
Your Skid Steer Articulating Brush Cutter are carefully designed and
manufactured to provide you with years of reliable service.
Your 48'' Skid Steer Articulating Brush Cutter will need some minor
maintenance to keep it in excellent working condition.
Please follow all safety precautions and maintenance procedures
described in this manual.
Please read and understand the instructions in this manual carefully
before operation. Please refer to the "Safety Labels" section for all
instructions noted above.
No one is allowed to operate his equipment who has not fully read and
understood this manual and has not been trained in safe deposit box
operations.
Remember to use only parts replaced by the manufacturer.
Replacement parts may not meet the standards required for safe and
reliable operation.
5
Wear appropriate safety glasses, goggles or face masks
Control Skid Steer Brush Cutter work, or any operation caused
by dust, flying Debris, or any other hazardous material.
Safety precautions
BEFORE OPERATION
1. The operator must read the operation manual carefully before installation, operation
or maintenance. Improper operation will cause the machine damaged or the
operator dead.
2. Read all the safe signs and safe declarations. Obey all the professional safe terms,
local laws or the professional directions.
3. Familiar with the duty Skid Steer Brush Cutter about functions, specs and operation.
Replace the to-be-damaged parts in time. Make sure all the hydraulic installations
and couplings connect firmly, and all the safe signs stick on the suitable positions
clearly.
ALWAYS watch for overhead power lines.
DO NOT place hands or feet under mower deck while blades are spinning.
NEVER operate this brush cutter when bystanders are within 300 feet of your work area.
Flying debris could cause serious injury or death.
NEVER position your body or limbs under an unsupported cutter deck.
DO NOT place hands or feet under mower deck while blades are spinning.
NEVER operate this brush cutter when bystanders are within 300 feet of your work
area. Flying debris could cause serious injury or death.
NEVER position your body or limbs under an unsupported cutter deck.
DO NOT allow this machine to contact buildings, utilities, large rocks or tree
stumps or you may lose control of the skid steer loader.
NEVER use drugs or alcoholic beverages while operating or servicing this machine.
ALWAYS operate this attachment during daylight or well-lit areas.
Install this brush cutter on a skid steer loader equipped with a thermoplastic
polycarbonate door panel and side panels only.
To prevent the skid steer loader and implement from rolling forward, stop the engine
and set the parking brake when exiting the skid steer loader.
Inspect implement for missing hardware prior to using this machine.
DO NOT allow children to play on or around this equipment at any time. Store this
implement in an area not frequented by children.
ALWAYS wear the proper personal protection equipment while operating or
servicing this machine. NEVER operate or service this machine with bare feet,
sandals, or other light footwear.
ALWAYS wear work gloves when handling cutter blades as they are often very
sharp.
ALWAYS use eye protection while operating or servicing this machine.
DO NOT speed Keep your driving speed between 2 and 5 mph.
6
Technical parameters
Model:
BDRC48
Max cutting diameter size:
48”
Working pressure （MPa）:
20
Total width:
56”
Total height:
21”
Total length：
133”
Total weight： （lb）
890
Suitable pressure （Mpa）:
16 ~ 21
Suitable flow rate （L/min）:
50 ~ 120
Rotate speed （r/min）:
905
Blade：
2
Drive mode：
The piston motor drives directly
Angle：
90°
Work environment：
Temperature: -20 ~ 50 °C
Height: 100 meters or less
Relative humidity :<85%
7
With the boom swung at 90°, you must be aware of any obstacles and
terrain in front of the cutter head and in front of your skid steer. Lack of
awareness may cause the skid steer loader or Articulating cutter to strike
obstacles that may result in serious injury or damage to equipment.
Tilt Function
The Articulating Cutter deck can tilt up 90° from the horizontal position and tilt down
35° from the horizontal position. Use the UP and DOWN buttons on your skid steer' s
auxiliary electric controller, or paddle controller to tilt the cutter head. The tilt function
is used for cutting on sloped terrain surfaces.
Technical parameters
8
Technical parameters
S/N
PART DESCRIPTION
QTYS
NOTE
1
Part 1
1
2
Part 2
2
3
Part 3
3
4
Bolt M12*80
2
5
Bolt M16*140
1
6
Locking nut M12
2
7
Turing Pivot
1
8
Lock Nut M16
2
9
Bolt M16*120
1
10
Pin
1
11
Cover
1
12
Lock Washer
1
13
Bolt M8*25
1
14
Front pin
1
15
Flip cylinder
1
16
Oscillating cylinder
1
9
Installation
Unpack and check
Check for missing or damaged components according to the packing list.
If you have any questions, please contact the supplier. List of details As the table above:
Machine installation
Equipment must be installed on a solid concrete floor or similar. If the ground is not firm,
it will not be able to connect to the loader. There should be a space around the device for
easy operation.
Connecting Brush Cutter
Consult your skid steer operator's manual for specific instructions on how to connect
your brush cutter to your skid steer loader.
General Attachment Method
1. Make sure the hydraulic lines are clear from the front side of the brush cutter's
attachment plate and that the locking pins on the skid steer mounting plate are
retracted.
2. Drive forward and place top of skid steer mounting plate under the attachment
mounting flange. See Figure 3.3 below.
3. Slowly raise and tilt back the skid steer mounting plate until the brush cutter
attachment plate rests flat against the skid steer mounting plate.
4. Activate your skid steer's lever lock switch to engage and lock the pins into the
flange slots of the brush cutter's attachment plate. If your skid steer does not have
this switch, push the latch handles down until you can see the lock pins extend into
the attachment flange.
5. Connect the attachment hydraulic hoses and the case drain hose (SBCNS model
only) to the auxiliary supply couplers located on your skid steer loader lift arm.
Skid Steer Mounting Plate to Attachment Mounting Flange
10
DO NOT operate this machine if you can see the cutter blade while
seated in the operator' s seat. If you can see the cutter blade, the
back of the cutter is raised TOO HIGH. Lower the cutter deck to
avoid from being struck by flying debris.
Installation
Connecting Brush Cutter Cont
To keep contaminants from entering the hydraulic system; wipe off any dirt or dust from
the male or female hydraulic flat face couplers with a clean rag before attaching hoses.
Check that the hydraulic hoses are locked into the skid steer couplers before starting the
cutter.
Connecting Electrical Harness
Connect the electrical attachment harness from the Articulating cutter to the electrical
bulkhead connector mounted on the skid steer loader arm. A universal, 7, 8, or 14 pin
pigtail harness adapter is available to make this connection. See Electrical Drawings, on
page 47 for more information.
Table des matières
