Agilent Technologies 16442A Manuel utilisateur
User’s Guide
Agilent 16442A Test Fixture
Agilent Part No. 16442-90000
Printed in Japan January 2000
Edition 3
2 Agilent 16442A User’s Guide, Edition 3
Legal Notice
The information contained in this document is subject to change without notice.
Copyright © 1994 - 2000 Agilent Technologies
This document contains information which is protected by copyright. All rights are
reserved. Reproduction, adaptation, or translation without prior written permission
is prohibited, except as allowed under the copyright laws.
•Product Warranty
Agilent Technologies warrant Agilent Technologies hardware, accessories and
supplies against defects in materials and workmanship for the period of one year
from the warranty start date specified below. If Agilent Technologies receive
notice of such defects during the warranty period, Agilent Technologies will, at
its option, either repair or replace products which prove to be defective.
Replacement products may be either new or like-new.
Warranty service of this product will be performed at Agilent Technologies.
Buyer shall prepay shipping charges to Agilent Technologies and Agilent
Technologies shall pay shipping charges to return the product to Buyer.
However, Buyer shall pay all shipping charges, duties, and taxes for products
returned to Agilent Technologies from another country.
Agilent Technologies do not warrant that the operation of Agilent Technologies
products will be uninterrupted or error free. If Agilent is unable, within a
reasonable time, to repair or replace any product to a condition as warranted,
customer will be entitled to a refund of the purchase price upon prompt return of
the product.
The Agilent Technologies products may contain remanufactured parts
equivalent to new in performance or may have been subject to incidental use.
The warranty period begins on the date of delivery or on the date of installation
if installed by Agilent Technologies. If customer schedules or delays Agilent
Technologies installation more than 30 days after delivery, warranty begins on
the 31st day from delivery.
Warranty does not apply to defects resulting from (a) improper or inadequate
maintenance or calibration, (b) software, interfacing, parts or supplies not
supplied by Agilent Technologies, (c) unauthorized modification or misuse, (d)
operation outside of the published environmental specifications for the product,
or (e) improper site preparation or maintenance.
Agilent 16442A User’s Guide, Edition 3 3
To the extent allowed by local law, the above warranties are exclusive and no
other warranty or condition, whether written or oral, is expressed or implied and
Agilent Technologies specifically disclaim any implied warranties or conditions
of merchantability, satisfactory quality, and fitness for a particular purpose.
Agilent Technologies will be liable for damage to tangible property per incident
up to the greater of $300,000 or the actual amount paid for the product that is the
subject of the claim, and for damages for bodily injury or death, to the extent
that all such damages are determined by a court of competent jurisdiction to
have been directly caused by a defective Agilent Technologies product.
To the extent allowed by local law, the remedies in this warranty statement are
customer’s sole and exclusive remedies. Expect as indicated above, in no event
will Agilent Technologies or its suppliers be liable for loss of date or for direct,
special, incidental, consequential (including lost profit or date), or other damage,
whether based in contract, tort, or otherwise.
For consumer transactions in Australia and New Zealand: the warranty terms
contained in this statement, except to the extent lawfully permitted, do not
exclude, restrict or modify and are in addition to the mandatory statutory rights
applicable to the sale of this product to you.
•Assistance
Product maintenance agreements and other customer assistance agreements are
available for Agilent Technologies products.
For any assistance, contact your nearest Agilent Technologies Sales Office.
•Certification
Agilent Technologies Inc. certifies that this product met its published
specifications at the time of shipment from the factory. Agilent further certifies
that its calibration measurements are traceable to the National Institute of
Standards and Technology (NIST), to the extent allowed by the Institute’s
calibration facility, and to the calibration facilities of other International
Standards Organization members.
•Safety Summary
The following general safety precautions must be observed during all phases of
operation, service, and repair of this instrument. Failure to comply with these
precautions or with specific warnings elsewhere in this manual may impair the
protections provided by the equipment. In addition, it violates safety standards
of design, manufacture, and intended use of the instrument. Agilent
Technologies Inc. assumes no liability for customer’s failure to comply with
these requirements.
4 Agilent 16442A User’s Guide, Edition 3
•GROUND THE INSTRUMENT
This is Safety Class I instrument. To minimize shock hazard, the instrument
chassis and cabinet must be connected to an electrical ground. The power
terminal and the power cable must meet International Electrotechnical
Commission (IEC) safety standards.
•DO NOT OPERATE IN AN EXPLOSIVE ATMOSPHERE
Do not operate the instrument in the presence of flammable gases or fumes.
Operation of any electrical instrument in such an environment constitutes a
definite safety hazard.
•KEEP AWAY FROM LIVE CIRCUITS
Operation personnel must not remove instrument covers. Component
replacement and internal adjustments must be made by qualified
maintenance personnel. Do not replace components with power cable
connected. Under certain conditions, dangerous voltages may exist even
with the power cable removed. To avoid injuries, always disconnect power
and discharge circuits before touching them.
•DO NOT SERVICE OR ADJUST ALONE
Do not attempt internal service or adjustment unless another person, capable
of rendering first aid and resuscitation, is present.
•DO NOT SUBSTITUTE PARTS OR MODIFY INSTRUMENT
Because of the danger of introducing additional hazards, do not install
substitute parts or perform any unauthorized modification to the instrument.
Return the instrument to a Agilent Technologies Sales and Service Office for
services and repair to ensure that safety features are maintained.
•DANGEROUS PROCEDURE WARNINGS
Warnings, such as example below, precede potentially dangerous procedures
throughout this manual. Instructions contained in the warnings must be
followed.
WARNING Dangerous Voltage, capable of causing death, are present in this instrument.
Use extreme caution when handling, testing, and adjusting.
Agilent 16442A User’s Guide, Edition 3 5
•Safety Symbols
The general definitions of safety symbols used on equipment or in manuals are
listed below.
Instruction manual symbol: the product will be marked with this symbol when it
is necessary for the user to refer to the instruction manual in order to protect
against damage to the instrument.
Indicates dangerous voltage and potential for electrical shock. Do not touch
terminals that have this symbol when instrument is on.
Protective conductor terminal. For protection against electrical shock in case of
a fault. Used with field wiring terminals to indicate the terminal which must be
connected to ground before operating equipment.
Frame or chassis terminal. A connection to the frame (chassis) of the equipment
which normally includes all exposed metal structures.
Indicates earth (ground) terminal.
Alternating current.
Direct current.
ON (Supply).
OFF (Supply).
STANDBY (Supply).
Means INSTALLATION CATEGORY I. Measurement terminals on the rear
panel comply with INSTALLATION CATEGORY I.
WARNING The warning sign denotes a hazard. It calls attention to a procedure, practice,
condition or the like, which, if not correctly performed or adhered to, could result in
injury or death to personal.
CAUTION The caution sign denotes a hazard. It calls attention to an operating procedure,
practice, condition or the like, which, if not correctly performed or adhered to, could
result in damage to or destruction of part or all of the product.
CAT 1
6 Agilent 16442A User’s Guide, Edition 3
•Herstellerbescheinigung
GEÄUSCHEMISSION
Lpa < 70 dB
am Arbeitsplatz
normaler Betrieb
nach DIN 45635 T. 19
•Manufacturer’s Declaration
ACOUSTIC NOISE EMISSION
Lpa < 70dB
operator position
normal operation
per ISO 7779
Printing History
Edition 1: February 1994
Edition 2: August 1997
Edition 3: January 2000
Agilent 16442A User’s Guide, Edition 3
User's Guide
2 Agilent 16442A User’s Guide, Edition 3
User's Guide
Agilent 16442A test fixture is designed for testing electronic devices. You mount
the suitable socket module on the 16442A, which allows you to easily connect
various devices (DUTs) to measurement units.
The 16442A has thirteen channels:
•6 source/monitor unit (SMU) channels
Up to 3 channels can be connected to SMUs by Kelvin connections.
•2 voltage source unit (VSU) channels
•2 voltage monitor unit (VMU) channels
•2 pulse generator unit (PGU) channels
•1 ground unit (GNDU) channel
This manual provides the following information.
•Introduction
•Operation
•Installation
•Maintenance
•Specifications
Agilent 16442A User’s Guide, Edition 3 3
User's Guide
Introduction
Introduction
Agilent 16442A test fixture contains the following accessories:
Description Agilent
Part Number Quantity
1 test fixture 16442-60001 1
2 stabilizer (with two flathead screws) 16442-60002 2
3 carrying case for socket modules 16442-60101 1
4 miniature banana to pin plug connection
cable (black)
16442-61600 4
5 miniature banana to pin plug connection
cable (red)
16442-61601 4
6 miniature banana to pin plug connection
cable (blue)
16442-61602 4
7 pin plug to pin plug connection cable
(black)
16442-61603 3
8 pin plug to pin plug connection cable (red) 16442-61604 3
4 Agilent 16442A User’s Guide, Edition 3
User's Guide
Introduction
NOTE Inspecting the 16442A upon Receiving
When the 16442A arrives at your site, make sure that nothing is missing or
damaged. Unpack the carton, then check the contents against figure and table above.
(For details about furnished and optional accessories, refer to “Specifications”.)
If anything is missing or damaged, contact your nearest Agilent Technologies sales
office.
9 pin plug to pin plug connection cable (blue) 16442-61605 3
10 miniature banana to miniature clip
connection cable (black)
16442-61606 3
11 miniature banana to miniature clip
connection cable (red)
16442-61607 3
12 miniature banana to miniature clip
connection cable (blue)
16442-61608 3
13 miniature banana to miniature banana
connection cable (black)
16442-61609 3
14 miniature banana to miniature banana
connection cable (red)
16442-61610 3
15 miniature banana to miniature banana
connection cable (blue)
16442-61611 3
16 blank TeflonTM board 16058-60004 1
17 dual-in-line package socket module (28-pin) 16088-60002 1
18 axial lead package socket module 16088-60009 1
19 TO-package socket module (12-pin) 16088-60006 1
20 User's Guide (this document) 16442-90000 1
Description Agilent
Part Number Quantity
Table des matières
Autres manuels Agilent Technologies Équipement de test
Agilent Technologies
Agilent Technologies U1401A Manuel utilisateur
Agilent Technologies
Agilent Technologies 16034E Manuel d'utilisation
Agilent Technologies
Agilent Technologies 16048A Manuel d'utilisation
Agilent Technologies
Agilent Technologies Infinium DCA 86100A Manuel utilisateur
Agilent Technologies
Agilent Technologies U3042AE08 Manuel utilisateur
Agilent Technologies
Agilent Technologies N4010A Instructions d'installation et d'utilisation
Agilent Technologies
Agilent Technologies 11644A Series Manuel
Agilent Technologies
Agilent Technologies N9360A Manuel du propriétaire
Agilent Technologies
Agilent Technologies E6001A Manuel utilisateur
Agilent Technologies
Agilent Technologies Agilent 34980A Instructions d'installation et d'utilisation
Agilent Technologies
Agilent Technologies 1000A Series Manuel utilisateur
Agilent Technologies
Agilent Technologies N9360A Manuel utilisateur
Agilent Technologies
Agilent Technologies BERT Serial Manuel utilisateur
Agilent Technologies
Agilent Technologies InfiniiVision 6000 Series Manuel utilisateur
Agilent Technologies
Agilent Technologies Infiniium 90000 Q-Series Manuel
Agilent Technologies
Agilent Technologies InfiniiVision 3000 X-Series Manuel utilisateur
Agilent Technologies
Agilent Technologies 16047A Manuel d'utilisation
Agilent Technologies
Agilent Technologies InfiniiVision 7000B Series Manuel utilisateur
Agilent Technologies
Agilent Technologies E1852A Manuel utilisateur
Agilent Technologies
Agilent Technologies 16197A Manuel d'utilisation
