Agilent Technologies 81101A Manuel utilisateur

Agilent 81101A 50 MHz Pulse Generator

Reference Guide

Per 1.000µ

µµ

µs Normal

OUTPUT TRG-LEVLIMITSMODE/TRG

OFF

Delay 1

0ps

Width

LeadE

TraiE

100.0ns

5.00ns

=LeadE

Offset

Amplit +0.0mV

1.00V

50Ω

ΩΩ

Ωinto 50.0Ω

ΩΩ

Ω

*OFF

MODIFY

GRAPH

Use the KNOB to select a

mode or modify parameters

and formats

Press ENTER or a UNIT key to

confirm parameter changes

Use the CURSOR keys to move

the entry focus to a mode,

parameter format, or

parameter value

Press a SOFTKEY to access

the required entry screen Press MORE key to access

the additional screen menus:

MODE/TRG TRG-LEV MEMCARD CONFIG

Screen Selection Area

Mode / Parameter Area Modify / Enter Area

Entry Focus

Front Panel Display and Softkeys

Reference Guide

Agilent 81101A 50 MHz

Pulse Generator

Part No. 81101-91021

Printed in Germany March 2000

Edition 1.0, E0300

Notice

No part of this manual may be reproduced in any form or by any means

(including electronic storage and retrieval or translation into a foreign

language) without prior agreement and written consent from Agilent

Technologies Inc. as governed by United States and international

Notice

The material contained in this document is subject to change without

notice. Agilent Technologies makes no warranty of any kind with regard

to this material, including, but not limited to, the implied warranties of

merchantability and fitness for a particular purpose. Agilent

Technologies shall not be liable for errors contained herein or for

incidental or consequential damages in connection with the furnishing,

performance, or use of this material.

Warranty

This Agilent Technologies product has a warranty against defects in

material and workmanship for a period of three years from date of

shipment. During the warranty period, Agilent Technologies will, at its

option, either repair or replace products that prove to be defective. For

warranty service or repair, this product must be returned to a service

facility designated by Agilent Technologies. The Buyer shall pay Agilent

Technologies round-trip travel expenses. For products returned to

Agilent Technologies for warranty service, the Buyer shall prepay

shipping charges to Agilent Technologies and Agilent Technologies shall

pay shipping charges to return the product to the Buyer. However, the

Buyer shall pay all shipping charges, duties and taxes for products

returned to Agilent Technologies from another country.

Notice

Agilent Technologies warrants that its software and firmware designated

by Agilent Technologies for use with an instrument will execute its

programming instructions when properly installed on that instrument.

Agilent Technologies does not warrant that the operation of the

instrument software, or firmware, will be uninterrupted or error free.

Limitation of Warranty

The foregoing warranty shall not apply to defects resulting from

improper or inadequate maintenance by the Buyer, Buyer-supplied

software or interfacing, unauthorized modification or misuse, operation

outside of the environmental specifications for the product, or improper

site preparation or maintenance. No other warranty is expressed or

implied. Agilent Technologies specifically disclaims the implied

warranties of merchantability and fitness for a particular purpose.

Exclusive Remedies

The remedies supplied are the Buyer's sole and exclusive remedies.

Agilent Technologies shall not be liable for any direct, indirect, special,

incidental, or consequential damages, whether based on contract, tort or

any other legal theory.

Certification

Agilent Technologies certifies that this product met its published

specifications at the time of shipment. Agilent Technologies further

certifies that its calibration measurements are traceable to the United

States Institute of Standards and Technology, to the extent allowed by

the Institute's calibrating facility, and to the calibration facilities of other

International Standards Organization members.

Services and Support

Any adjustment, maintenance, or repair of this product must be

performed by qualified personnel. Contact your customer engineer

through your local Agilent Technologies Service Center. You can find a

list of local service representatives on the Web at:

http://www.agilent.com/Service/English/index.html

Safety Summary

The following general safety precautions must be observed during all

phases of operation of this instrument. Failure to comply with these

precautions or with specific warnings elsewhere in this manual violates

safety standards of design, manufacture, and intended use of the

instrument. Agilent Technologies Inc. assumes no liability for the

customer's failure to comply with these requirements.

General

This product is a Safety Class 1 instrument (provided with a protective

earth terminal). The protective features of this product may be impaired

if it is used in a manner not specified in the operation instructions.

All Light Emitting Diodes (LEDs) used in this product are Class 1 LEDs

as per IEC 60825-1.

Environmental Conditions

This instrument is intended for indoor use in an installation category II,

pollution degree 2 environment. It is designed to operate at a maximum

relative humidity of 95% and at altitudes of up to 2000 meters. Refer to

the specifications tables for the ac mains voltage requirements and

ambient operating temperature range.

Before Applying Power

Verify that the product is set to match the available line voltage, the

correct fuse is installed, and all safety precautions are taken. Note the

instrument's external markings described under Safety Symbols on

page 8.

Safety Summary

Ground the Instrument

To minimize shock hazard, the instrument chassis and cover must be

connected to an electrical protective earth ground. The instrument must

be connected to the ac power mains through a grounded power cable,

with the ground wire firmly connected to an electrical ground (safety

ground) at the power outlet. Any interruption of the protective

(grounding) conductor or disconnection of the protective earth terminal

will cause a potential shock hazard that could result in personal injury.

Fuses

Only fuses with the required rated current, voltage, and specified type

(normal blow, time delay, etc.) should be used. Do not use repaired fuses

or short-circuited fuse holders. To do so could cause a shock or fire

hazard.

Do Not Operate in an Explosive Atmosphere

Do not operate the instrument in the presence of flammable gases or

fumes.

Do Not Remove the Instrument Cover

Operating personnel must not remove instrument covers. Component

replacement and internal adjustments must be made only by qualified

service personnel.

Instruments that appear damaged or defective should be made

inoperative and secured against unintended operation until they can be

repaired by qualified service personnel.

Safety Summary

Safety Symbols

Caution (refer to accompanying documents)

Protective earth (ground) terminal

In the manuals:

WARNING The WARNING sign denotes a hazard. It calls attention to a

procedure, practice, or the like, which, if not correctly performed

or adhered to, could result in personal injury. Do not proceed

beyond a WARNING sign until the indicated conditions are fully

understood and met.

CAUTION The CAUTION sign denotes a hazard. It calls attention to an operating

procedure, or the like, which, if not correctly performed or adhered to,

could result in damage to or destruction of part or all of the product. Do

not proceed beyond a CAUTION sign until the indicated conditions are

fully understood and met.

About this Book

This guide provides reference information primarily for programming the

Agilent 81101A via remote control.

Chapter 1 “General Programming Aspects” on page 13 gives general

hints for programming instruments like the Agilent 81101A using SCPI

commands.

Chapter 2 “Programming Reference” on page 25 provides detailed

information on the SCPI commands supported by the instrument.

Chapter 3 “Specifications” on page 89 lists the instrument’s technical

specifications and provides exact definitions for the instrument’s

parameters.

For an introduction and information on the Agilent 81101A’s user

interface, please refer to the Quick Start Guide, p/n 81101-91020.

About this Book

Conventions Used in this Book

This book uses certain conventions to indicate elements of the

Agilent 81101A’s user interface. The following table shows some

examples:

Softkeys Press the MODE/TRG softkey to access the Mode/

Trigger screen.

Hardkeys Press the MORE key to switch to the alternative

softkey layout.

Alternate Keys Press SHIFT + 0 (ON/OFF) to switch on the output.

The alternate key label—which is selected by

pressing the SHIFT key—is given in parentheses.

Screen Quotes Move the entry focus down to PULSE-PERIOD and

turn the knob to select INTERNAL PLL.

Entry Focus The highlight field, that can be moved with the

cursor keys, to change modes, parameters, or

parameter formats.

:VOLTage:HIGH 3V

Full command for programming a 3 V high level.

The upper case letters represent the short form

of the command, which results in faster pro-

gramming times.

*RST Common IEE 488 command, to reset instrument

to default status.

Autres manuels pour 81101A

Table des matières

Autres manuels Agilent Technologies Générateur d'impulsions

Agilent Technologies

Agilent Technologies E8305A Manuel utilisateur

Agilent Technologies

Agilent Technologies 8133A Manuel utilisateur

Agilent Technologies

Agilent Technologies 8130A Guide de démarrage rapide

Agilent Technologies

Agilent Technologies 81150A Manuel utilisateur

Agilent Technologies

Agilent Technologies 222A Manuel utilisateur

Agilent Technologies

Agilent Technologies 8131A Manuel utilisateur

Agilent Technologies

Agilent Technologies 81110A Manuel utilisateur

Agilent Technologies

Agilent Technologies 81110A Guide de démarrage rapide

Agilent Technologies

Agilent Technologies 81133A Manuel utilisateur

Agilent Technologies

Agilent Technologies 81104A Manuel utilisateur

Agilent Technologies

Agilent Technologies N6030A Series Manuel utilisateur

Agilent Technologies

Agilent Technologies 8114A Manuel utilisateur

Agilent Technologies

Agilent Technologies E4438C Manuel utilisateur

Agilent Technologies

Agilent Technologies 81150A Manuel utilisateur

Agilent Technologies

Agilent Technologies 8114A Manuel utilisateur

Agilent Technologies

Agilent Technologies 16440A Manuel utilisateur

Manuels Générateur d'impulsions populaires d'autres marques

HP 8082a Manuel de service

Schwarzbeck

Schwarzbeck IGUU 2916 Manuel utilisateur

Anaheim Automation

Anaheim Automation MBC10P31 Manuel utilisateur

BIOTRONIK

BIOTRONIK Philos DR-T Manuel utilisateur

BNC

BNC 575 Series Manuel utilisateur

Hioki

Hioki U8793 Manuel utilisateur

HP 8012A Manuel utilisateur

Bradley

Bradley 233 Manuel utilisateur

DEI

DEI PCX-7500 Manuel utilisateur

Kiepe Elektrik

Kiepe Elektrik DG Series Manuel utilisateur

Hagerman Technology

Hagerman Technology FryBaby Manuel utilisateur

BNC

BNC MOD745T Manuel utilisateur

AVTECH ELECTROSYSTEMS LTD.

AVTECH ELECTROSYSTEMS LTD. AVG-4A-B Manuel utilisateur

Avtech

Avtech AVR-G1-B Manuel utilisateur

Avtech

Avtech AVOZ-D2-B Manuel utilisateur

Tektronix

Tektronix 114 Manuel utilisateur

AVTECH ELECTROSYSTEMS LTD.

AVTECH ELECTROSYSTEMS LTD. AVR-E5-B Manuel utilisateur

BNC

BNC 505-2C Manuel utilisateur