AGA DC3 Manuel utilisateur

Installation

Guide

09/14 EINS 516664

PLEASE READ THESE INSTRUCTIONS BEFORE COMMENCING SITE SURVEY

OR INSTALLING THIS APPLIANCE.

IMPORTANT : SAVE INSTRUCTIONS FOR FUTURE REFERENCE

IMPORTANT : CONSERVER CES INSTRUCTIONS POUR REFERENCE FUTURE

For use in USA/Canada

AGA DUAL CONTROL

Model No. - DC3 & DC5

SECTION PAGE

PRODUCT SAFETY 3

GENERAL NOTES 4

DELIVERY REQUIREMENTS 4

GENERAL INSTALLATION REQUIREMENTS 4

APPLIANCE DIMENSIONS - AGA DC3 5

APPLIANCE DIMENSIONS - AGA DC5 6

INSTALLATION 7 - 8

CONNECTION TO THE POWER SUPPLY - AGA DC3 9

POWER SUPPLY - HOT CUPBOARD AGA DC5 10

MAINS SUPPLY LOCATION - AGA DC3 11

MAINS SUPPLY LOCATION - AGA DC5 12

HOTCUPBOARD INSTALLATION 13 - 19

WIRING DIAGRAM - AGA DC3 20

WIRING DIAGRAM - AGA DC5 21

INSTRUCTIONS 22

CONTENTS

PRODUCT SAFETY

MEANING/DESCRIPTION SIGNIFICATION/DESCRIPTIONSYMBOL

WARNING/CAUTION

An appropriate safety instruction

should be followed or caution to a

potential hazard exists.

AVERTISSEMENT

Une consigne de sécurité

appropriée doivent être suivies

ou garde d’un danger potentiel

exists.

DANGEROUS VOLTAGE

To indicate hazards arising from

dangerous voltages.

TENSION DANGEREUSE

Pour indiquer les dangers

résultant des tensions

dangereuses.

PROTECTIVE EARTH (GROUND)

To identify any terminal which is

intended for connection to an

external conductor for protection

against electric shock in case of

a fault, or the terminal of a

protective earth (ground)

electrode.

TERRE DE PROTECTION

Pour marquer bornes destin

ées à

être raccordées à un conducteur

de protection extérieur contre les

chocs éclectiques en cas de

défaut d’isolement, ou pour

marquer la borne de la terre de

protection.

HEAVY

This product is heavy and

reference should be made to the

safety instructions for provisions

of lifting and moving.

LOURD

Ce produit est lourd et doit

être

fait référence auc consignes de

sécurité relatives aux dispositions

de soulever et déplacer.

DISCONNECT MAINS SUPPLY

Disconnect incoming supply

before inspection or

maintenance.

APPAREIL À LASER DE

CLASSE 2

Alimentation d’entr

ée Débrancher

avant inspection ou d’entretien.

REFER TO MANUAL

Refer to relevant instructions

detailed within the product

manual.

ATTENTION, SURFACE TRÉS

CHAUDE

Reportez-vous aux instructions

applicables, indiquées dans le

manuel du produit.

GENERAL NOTES

NOTE: THESE INSTALLATION INSTRUCTIONS SHOULD BE LEFT WITH THE RANGE AND

THE USER TO RETAIN FOR FUTURE REFERENCE.

DELIVERY REQUIREMENTS

The AGA DC3 arrives on 1 pallet.

The AGA DC5 (Hotcupboard Option) arrives on 2 pallets.

There must be access to the kitchen to manipulate a foot print of 39 9/16” (1005mm) x 29 1/8”

(740mm). A wooden template (skate with castor wheels) of dimensions 39 9/16” (1005mm) x

29 1/8” (740mm) could be used to check if the AGA Dual Control fully built appliance is able to

fit through the property grounds and doors into its installation position in the kitchen. It must

also be considered that the height of the appliance is 37 3/4” (960mm) off pallet and 43 1/4 ”

(1100mm) on the pallet, so high level obstacles/restrictions must not be overlooked.

If this skate/template can be manipulated through the property grounds and doors

into position, then the AGA Dual Control can be installed as intended with no re-work.

GENERAL INSTALLATION REQUIREMENTS

The installation of the range must be in accordance with the relevant requirements of the local

Wiring and Building Regulations. It should be in accordance also with any relevant requirements

of the Local Authority.

In your own interest and that of safety to comply with the law, all appliances should be installed

by an authorized AGA distributor in accordance with the relevant regulations.

CAUTION:

THIS UNIT IS HEAVY, PROPER EQUIPMENT AND ADEQUATE

MANPOWER MUST BE USED IN MOVING THE RANGE TO

AVOID DAMAGE TO THE UNIT OR THE FLOOR

APPLIANCE DIMENSIONS - AGA DC3

Fig. 1 DESN 516297

Range Dimensions

When surveying for a range installation the actual clearance required for the ‘body’ of the

appliance should be increased by 3/8” (10mm) beyond the figures quoted above. This allows

safe margin to take into account the natural dimensional variations found in major castings. In

particular the width across the appliance recess could be critical.

APPLIANCE WEIGHT (Excludes Packaging)

Model: AGA Dual Control (DC3) - 978 lbs

DATA PLATE LOCATED BEHIND BOTTOM PLINTH.

RH SIDE VIEW FRONT VIEW LH SIDE VIEW

PLAN VIEW

MINIMUM WALL POSITION MINIMUM WALL POSITION

A B C D E F G H J K L

mm 987 948 910 680 1388 760 1145 698 116 10 634

pouces 38 7/837 3/835 7/826 3/454 5/829 7/845 1/827 1/245/83/825

APPLIANCE DIMENSIONS - AGA DC5

Fig. 2 DESN 516561

Range Dimensions

When surveying for a range installation the actual clearance required for the ‘body’ of the

appliance should be increased by 3/8” (10mm) beyond the figures quoted above. This allows

safe margin to take into account the natural dimensional variations found in major castings. In

particular the width across the appliance recess could be critical.

APPLIANCE WEIGHT (Excludes Packaging)

Model: AGA Dual Control (DC5) - 978 lbs

Hotcupboard - 242 lbs

DATA PLATE LOCATED BEHIND BOTTOM PLINTH.

A B C D E F G H J K L

mm 1478 948 910 680 1388 760 1145 698 116 10 634

ins 58 1/ 37 3/835 7/826 3/454 5/829 7/845 1/827 1/245/83/825

INSTALLATION

Range Base or Hearth

It is essential that the base or hearth on which the range stands should be level and be capable

of supporting the total weight of the range. The base of the built-in AGA plinth must be level and

sit above finished floor height for service access.

Plinth

The front plinth cover is removable and must not be obstructed by flooring or tiles. If necessary

the range must be raised by the thickness of the tiles to ensure the plinth can be removed.

Rear Wall

The wall behind the range must be of non-combustible material with a minimum thickness of 1”

(25mm).

Minimum Clearance to Combustibles

A gap of at least 1/2” must be observed between the rear of the top plate, and the wall behind the

range. If the rear wall is of combustible material there must be a gap of 11/2” (38mm).

Side Clearances

A 1/8” (3mm) gap is required each side between the range top plate and adjoining work surfaces

that may be fitted, this is to allow for the safe removal of the top plate should this be required at

a later date.

Where ranges are fitted against a side wall a 4 5/8” (116mm) side clearance is required on the

right and left hand side for oven door access.

If the AGA is to be installed in a brick recess, then the minimum clearance should be increased

by at least 3/8” (10mm), to allow for the walls not being square.

In addition a minimum clearance of 39 3/8” (1000mm) must be available at the front of the range

to enable the range to be serviced.

Tiling

When the range is to stand in a recess or against a wall which is to be tiled, under no

circumstances should the tiles overlap the range top plate, access to remove the hotplate must

be allowed for servicing at a later date.

A gap of at least 1/2” (12mm) must be observed between the rear of the top plate and the wall

behind the range.

Overhead Cabinets

To eliminate the risk of burns or fires by reaching over hot surface units, cabinet storage space

located above the surface units should be avoided.

Range Hoods

It is recommended that this AGA is fitted with a range hood. The AGA venting system is located

on top of the AGA between the two hotplates, and is designed for venting the moisture from the

ovens. The range hood should be positioned not less than the minimum height as recommended

by the manufacturer, from the top of the AGA.

NOTE: ANY OVERHEAD FITTED

CABINETS MUST NOT EXCEED 13”

PROJECTED DEPTH ABOVE THE

RANGE.

DIM ‘D’ TO BE NOT LESS THAN THE

NORMAL WIDTH OF THE RANGE.

Fig. 3 DESN 51668

CONNECTION TO THE POWER SUPPLY - AGA DC3

Electric Shock Hazard

Rating Plate is located behind removable plinth, see Fig. 4.

Electrical Grounding is required on this appliance.

DO NOT connect to the electrical supply until the appliance is

permanently grounded.

This appliance must be connected to a grounded metallic permanent

supply or a grounding connector should be connected to the grounding

terminal or wire lead on the appliance.

Failure to follow these instructions could result in death or serious injury.

This range must be supplied with a 240V, 60Hz power supply and connected to an individual,

properly grounded branch circuit protected by a circuit breaker. At 240V, it has a maximum load

of 30 amps. Electric hook-up must be done by a licensed electrician. This unit must be installed

according to regional codes, or in the absence of codes, the National Electrical Code.

lProduct installation requires a separate (not shared) 240V/40 amp circuit protected by an

appropriate branch circuit supply.

lThe service cord on your range is fitted with a standard four (4) conductor type 14-50P plug

(matching receptacle 14-50R).

The method of connection to the mains electricity supply must facilitate complete electrical

isolation of the appliance.

The mains connection and isolation should not be positioned above the range and must be

positioned within the area defined in Fig. 4, Page 11.

THIS RANGE MUST BE COMPLETELY ISOLATED FROM THE ELECTRICITY SUPPLY

BEFORE SERVICING. THE RANGE IS DESIGNED FOR THE VOLTAGE STATED ON THE

RATING PLATE, WHICH IS SITUATED BEHIND THE PLINTH COVER.

POWER SUPPLY - HOTCUPBOARD (AGA DC5)

The hotcupboard attachment requires an independent single phase supply. It has a

maximum load of 6 amps, protected by an appropriate branch circuit supply.

110/120V 60 Hz FLEXIBLE CORD and PLUG PARALLEL TYPE (NEMA 5-15P). The appliance

when installed must be electrically grounded in accordance with local or regional codes.

An electrical socket must be provided within 5 feet of the LH side of the appliance and easily

accessible for the user to disconnect. Do not position socket above the appliance. See Fig. 5A,

Page 12.

Take special care when cutting holes in wall or floor. Electrical wires may be behind the wall or

floor covering and could cause an electrical shock if you touch them.

Locate any electrical circuits that could be affected by the installation of this product and

disconnect power circuit.

WARNING

Electrical Grounding Instructions

This appliance is equipped with a NEMA 5-15P grounded plug for your protection against a

shock hazard and should be plugged directly into a proper receptacle. Do not cut or remove the

grounding prong from this plug.

Do not have a fuse in the neutral or grounding circuit. A fuse in the neutral or grounding circuit

could result in electrical shock.

Do not use an extension lead with this appliance.

Check with a qualified electrician, if you are not sure the appliance is properly grounded.

Failure to follow these instructions could result in death or serious injury.

Autres manuels pour DC3

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels AGA Poêle

AGA

AGA Ellesmere Instructions de fonctionnement

AGA

AGA LUDLOW ECG Instructions de fonctionnement

AGA

AGA Ellesmere Series Manuel utilisateur

AGA

AGA BERRINGTON NON BOILER Manuel utilisateur

AGA

AGA MUCH WENLOCK CLASSIC Manuel utilisateur

AGA

AGA ELLESMERE 4K Manuel utilisateur

AGA

AGA TC3 Manuel utilisateur

AGA

AGA Little Wenlock Classic Manuel utilisateur

AGA

AGA Ellesmere EC5W Manuel utilisateur

AGA

AGA Ellesmere Wide Instructions d'installation

AGA

AGA Wren NB Manuel utilisateur

AGA

AGA Little Wenlock Classic Manuel utilisateur

AGA

AGA LITTLE WENLOCK Manuel

AGA

AGA Ludlow Mode d’emploi

AGA

AGA MINSTERLEY Manuel utilisateur

AGA

AGA LITTLE WENLOCK Manuel utilisateur

AGA

AGA SIX-FOUR SERIES - DC6 Manuel utilisateur

AGA

AGA Berrington Manuel utilisateur

AGA

AGA Stretton Manuel utilisateur

AGA

AGA MUCH WENLOCK NON- BOILER Manuel utilisateur

AGA

AGA Ludlow Non-Boiler Manuel utilisateur

Manuels Poêle populaires d'autres marques

Arada

Arada Cassette Stove Manuel utilisateur

Parmco

Parmco FS 600 Manuel utilisateur

MCZ

MCZ SUITE AIR 10 M2 Manuel utilisateur

HearthStone

HearthStone Stowe DV 8321 Guide de dépannage

Cattara

Cattara FAMILY Manuel utilisateur

Stanley

Stanley Argon F500 OVAL Manuel utilisateur

Avalon

Avalon B-VENT Manuel utilisateur

Nordpeis

Nordpeis Vega Manuel utilisateur

Exquisit

Exquisit EKC601-5 Manuel d'utilisation

Stanley

Stanley Oisin Oil MK II Manuel du propriétaire

Thermocet

Thermocet Brookfield S/CC Manuel utilisateur

HASE

HASE delhi Manuel utilisateur

Vermont Castings

Vermont Castings Intrepid 2 Manuel utilisateur

Italiana Camini

Italiana Camini CLASSICA Guide de démarrage rapide

Avalon

Avalon Vashon Avanti DVS FS Manuel utilisateur

Spartherm

Spartherm ambiente a1 Manuel utilisateur

Dimplex

Dimplex MCFSTV12AU Manuel utilisateur

Warmlite

Warmlite WL46040 Manuel utilisateur