AG Neovo LOC-32 Manuel utilisateur

Assembly Guide of

LOC-Series Display Enclosure

Page 2

Table of Contents

1. General information: LOC-Series Display Enclosure ....................................................................... 3

2. Scope of delivery ............................................................................................................................. 3

3. Preparations for installation and comissioning............................................................................... 4

4. Mounting the monitor................................................................................................................... 10

5. Maintenance.................................................................................................................................. 13

5.1 General information on cleaning and maintenance ............................................................. 13

5.2 Changing the filters ............................................................................................................... 13

5.3 Miscellaneous........................................................................................................................ 13

6. Technical data................................................................................................................................ 14

7. Technical drawings ........................................................................................................................ 14

4.1 Assembly for freestanding outdoor enclosure 32”-55” LOC-Series ..................................... 12

Assembly Guide of LOC-Series Display Enclosure

Assembly Guide of LOC-Series Display Enclosure Page 3

1. General information: LOC-Series Display Enclosure

The LOC-Series display enclosure is equipped with a sturdy metal casing and has both a ventilation

and a heating system. In outdoor use, it provides protection against humidity, wetness and

heat as well as vandalism and theft. The devices comply with the IP54/IP65 protection standard and

can be used in a temperature range from -20 ° to 40 ° C.

2. Scope of delivery

1) Housing (metal enclosure)

1 pc

2) Keys (coded –please record and store number)

2 sets

3) Beam to be attached to VESA fitting

2 pcs

4) Cable gland/ strain relief (25 mm) to feed- through ethernet cable

1 pc

5) Cable gland / strain relief (16 mm) to feed-through main connection (230 V/16A)

1 pc

6) Screws for fixing the beam to the monitor

7) Paper template for drilling

8) Standard mounting kit for wall assembly

Assembly Guide of LOC-Series Display Enclosure Page 4

3. Preparations for installation and comissioning

For the assembly you need the following tools:

1) Hammer drill

2) Spirit level and pencil

3) Dowels and screws to match wall structure

4) Small slotted screwdriver or phase tester

5) 10 mm jaw spanner for mounting/dismantling the monitor holder

6) 8 mm jaw spanner to fix door braces

7) Water pipe plier for screwing the cable glands

8) 4 mm Allen key wrench for mounting the supporting arms on the monitor

9) Open-end spanner (17 mm) to tighten the nuts (M10) on the hanger bolts

Please make sure that the desired installation location provides a 230 V power supply and internet

access option.

When mounting, please make sure that the respective wall has a sufficient load capacity for the

weight of the housing and display (for weight see data sheet). When choosing the location, we

recommend selecting positions with as much shade as possible or without intense sun exposure. This

increases the readability of the monitor in bright light conditions.

IMPORTANT! Prior to installation, please make sure that the power supply in the wall is

disconnected/turned off!

Mounting should be carried out by two persons.

Assembly Guide of LOC-Series Display Enclosure Page 5

Wall mounting of the metal housing

Starting with model series 2018, the housing is mounted directly and without wall bracket, using the

hanger bolts in the accessory package. Please check if the wall structure is suitable for this type of

mounting (other mounting systems are not included).

1) Use the supplied drilling template/wall plate to mark the drill holes on the mounting wall,

use a spirit level to position the plate. For the drilling template, please make sure to select

the correct model size!

2) Then drill the necessary holes in the wall using a hammer drill with a suitable drill. Make sure

that the holes are at least 10 cm away from the outer edge of the wall and are inserted

perpendicularly into the wall.

3) Insert dowels and hanger bolts with nuts in the wall, according to the following section

drawing. A standard mounting kit with the required mounting material is included in the

package.

For wall mounting of the housing, please use M10 hanger bolts with corresponding dowels and a

metric thread length LM of 50 mm. Depending on the type of wall, the total length I and LH must be

selected.

Furthermore, you need 2 body washers per bolt, e.g. M10, DIN 440R (ISO 7094), Da = 34 mm, Di = 11

mm, T = 3 mm, as well as 2 nuts (M10). For each hanger bolt, rotate one M10 nut onto the thread.

Then insert a body washer on the hanger bolt.

Make sure that the enclosure's distance from the wall is not less than 30 mm (red arrows on the

section drawing). Set a distance of ≥ 30 mm with the nut.

Lift the housing onto the hanger bolts, secure it against falling down and open the door. Place a

washer on each hanger bolt and tighten the housing with the nuts from inside.

Assembly Guide of LOC-Series Display Enclosure Page 6

Assembly Guide of LOC-Series Display Enclosure Page 7

Securing the door against accidental slamming or

impact while lying flat:

After opening, secure the door with the provided door

struts. For this purpose –as illustrated –position and

hook the lifting eye of the door strut on the bolt

between the nut and the housing edge and tighten the

nut to prevent the door strut from slipping out.

Please pay close attention to this procedure, otherwise

there is a high risk of crushing or injury by the door

slamming shut.

Lay down the housing with its back on a clean and padded surface. Unlock the door with the keys.

Closing direction of the lock:

Right side of door: Close in clockwise and

open in counter clockwise direction.

Left side of door: Open in counter clockwise

and close in clockwise direction.

When closing and opening the locks, gently press the

door against the housing. This will compress the

gasket and facilitate the closing process.

Open the door. ATTENTION! Please guide the door with your hand and hold firmly so it does not

move. Fold out the door struts (located on the narrow sides of the door on the inside) and insert the

holding loop - as shown in the picture - into the holder.

Assembly Guide of LOC-Series Display Enclosure Page 8

Installing the cable glands before mounting the housing

Screw the base body with the lock

nut as shown. Remove the

standard gasket. Pass the LAN

cable through. Place the slotted

gasket around the LAN cable and

insert it into the base body.

Provide sufficient cable length to

the PC. Screw and tighten the

union nut.

Screw the base body with the lock

nut as shown. Pass the power

cable through. Ensure sufficient

cable length to the connection

terminals. Screw and tighten the

union nut.

Assembly Guide of LOC-Series Display Enclosure Page 9

Prior to connecting the primary

circuit, please loosen the indicated

screws and remove the monitor

holder. After the power cable has

been plugged in, screw the

monitor holder tightly (torque

max. 5 Nm), two nuts per side.

Yellow = PE

Afterwards, you can continue clamping the power supply.

Connection terminals on primary

side from left to right:

Black = L

Blue = N

Connecting the cables

Setting up the power supply system

In order to connect the housing to the main supply, there is a power distribution terminal strip with 3

terminals (L: Grey, N: Blue, PE: Green/yellow) located inside of the device. Please note that the

connection may only be set up by a trained professional or an electrician.

When connecting, make sure that there is no voltage on the power supply line.

To get to the terminals, the monitor holder must be removed.

After power is connected, the monitor mount must be reinstalled.

Assembly Guide of LOC-Series Display Enclosure Page 10

4. Mounting the monitor

Please follow the instructions below to prevent damage to the monitor during installation:

First, please look for a clean and flat surface. When unpacking, make sure not to

scratch the surface of the screen and avoid pressure load on the surface. Therefore,

it is important that you thoroughly scan the storage area for objects such as screws

or dirt.

1) Take the monitor out of the cardboard box while keeping it up and always vertical.

2) Take the monitor arms and screw them back to the monitor with the supplied screws. Align

the arms centre to the horizontal axis of the monitor. Make sure that the distance between

the monitor edge and the mounting arm is the same at the top and bottom (averaged).

Observe the mounting direction of the mounting arms. They must be mounted in such a way

that the narrow-slit points upward. Otherwise the monitor cannot be hung.

3) Connect the required cables to the monitor.

a. HDMI-cable

b. Power cable

4) Now, with the cables connected, insert the monitor into the housing. A corresponding device

for this purpose is attached on the inside of the housing.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels AG Neovo Moniteur

AG Neovo

AG Neovo TX-22 Manuel utilisateur

AG Neovo

AG Neovo S-15E Manuel utilisateur

AG Neovo

AG Neovo HX-32 Manuel utilisateur

AG Neovo

AG Neovo DR-17P Manuel utilisateur

AG Neovo

AG Neovo F-417 Manuel utilisateur

AG Neovo

AG Neovo H-19 Manuel utilisateur

AG Neovo

AG Neovo HMQ-4301 Manuel utilisateur

AG Neovo

AG Neovo QD-75 Manuel utilisateur

AG Neovo

AG Neovo DR-17 Mode d’emploi

AG Neovo

AG Neovo RX-W22 Manuel utilisateur

AG Neovo

AG Neovo RX-22G Manuel utilisateur

AG Neovo

AG Neovo SC-19 Manuel utilisateur

AG Neovo

AG Neovo X-17 Manuel utilisateur

AG Neovo

AG Neovo E-17 Manuel utilisateur

AG Neovo

AG Neovo QM-43 Manuel utilisateur

AG Neovo

AG Neovo X-W22 Manuel utilisateur

AG Neovo

AG Neovo LE-22 Manuel utilisateur

AG Neovo

AG Neovo X-15 Manuel utilisateur

AG Neovo

AG Neovo TX-42 Manuel utilisateur

AG Neovo

AG Neovo ER-19 Manuel utilisateur

AG Neovo

AG Neovo F-419 Manuel utilisateur

AG Neovo

AG Neovo U Series Manuel utilisateur

AG Neovo

AG Neovo C-Series Manuel utilisateur

AG Neovo

AG Neovo DR-17 Manuel utilisateur

Manuels Moniteur populaires d'autres marques

Linear Acoustic

Linear Acoustic LQ-1000 Manuel utilisateur

AOC

AOC I2579V Manuel utilisateur

Gateway

Gateway FPD1520 Manuel utilisateur

Furuno

Furuno Mu 120c Manuel utilisateur

Asus

Asus VB171D - 17" LCD Monitor Manuel utilisateur

Dell

Dell S2230MX Instructions d'utilisation

Philips

Philips 107C64 Manuel utilisateur

Dell

Dell S2409WFP Manuel utilisateur

EverFocus

EverFocus EN-7517E Manuel utilisateur

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Manuel utilisateur

Dell

Dell Precision 7680 Mode d’emploi

LG 50PM1M - - 50" Plasma Panel Manuel utilisateur

Bosch

Bosch DDU 9 Manuel utilisateur

Acer

Acer A231HL Manuel utilisateur

Philips

Philips 86BDL4152T Manuel utilisateur

NEC

NEC AccuSync LCD5V Manuel utilisateur

Emay

Emay SleepO2 Manuel utilisateur

IBM

IBM 6360 Instructions d'installation