AFL Hyperscale 10011505 Manuel utilisateur
Level 4 Distribution Cabinet
Installation Guide
POC
VIRGIN MEDIA APPROVED
INSTALLATION METHOD
SKU: 10011505
2
Network Topology
2f Blown
Element
12f Blown
Element
144f
Trunk Cable
Trunk
Cable
Headend/Hub (L1/L2)
VM Hub (L2.5)
Passive Distribution Node (L4) Passive Distribution Node (L4)
Passive Aggregation Node (L3)
The PoC L4 distribution cabinet
provides a splicing, splitter and
patching point for the nal
drop to the home
PoC Level 4 Distribution Cabinet Installation Guide
3
Network Distribution
Cable Tie Point
Backboard
Cable Manager
Customer
Drop Patch
Panel
Patching
Chassis
Customer Drop
Duct Tie Point
Cable / Tube
Manifold
Modular Raceway
24f Splice Tray
Splitter Tray
Item Quantity
Backboard 1
Cable Managers 8
Bend Radius Manager 1
Network Distribution Cable Tie Point 1
24f Splice Tray 6
Splitter Tray 6
Modular Raceway 4
Cable/Tube Manifold 1
8 Way Customer Drop Duct Tie Point 6
Customer Drop Patch Module 6
Patching Chassis 1
Component Overview
4
Slot studs into back panel - No tools required. Backboard must be central, top, loction as shown
1
Rear Section View
Installation Process Mount Backboard
Into Cabinet
PoC Level 4 Distribution Cabinet Installation Guide
5
Always install ducts from rear to front
Cut ducks to lenght, clip into position
(use a cable tie to straighten out duct
as required)
2Push on blowing indicator (not supplied)
3
Network Distribution Cable Customer Drop Cables
20mm Approx
20mm Approx
Micro Duct Installation
6
Tighten Gas Block
6
Install 12f cable - minimum overlength 3m from gas block
4
Network Cable Preparation and Dressing
Feed Cable Through Guide
5
PoC Level 4 Distribution Cabinet Installation Guide
7
Tie off micro duct
7Mark strip point at start of raceway
8
Strip the jacket in accordance with the cables manufacturers guidelines
9
Strip Point
8
Route 250μm bers through raceway, dress ber into tray (as per map)
NO TRANSPORT TUBING REQUIRED
10
Incoming Cable Route
No Transport
Tubing Required
PoC Level 4 Distribution Cabinet Installation Guide
9
Cassette
8
Cassette
7
Cassette
6
Cassette
5
Cassette
4
Cassette
3
CABLE #1
Pink/Rose
Aqua
Black
White
Violet
Red
Yellow
Grey
Brown
Green
Orange
Blue
Cable / Cassette Fiber Map
Splitter Input
(900μm)
Network Fiber
(250μm)
Splitter Outputs
(900μm)
Splice Protector
* Virgin Media recommended ber routing.
PLEASE CHECK SPLICING SCHEDULE!
Splice the network cable to the splitter input
11 Make sure the tray lid is tted after splicing
12
10
Straight Splice L4-L4 Pass Through (Point To
Point Between L3 and Last L4)
Incoming Cable
Incoming Cable
Outgoing Fiber
(250μm) Incoming Fiber
(250μm)
Outgoing Cable
Outgoing Cable
Strip Cable Jacket / Subunit within this area
Splice Incoming Fiber to Outgoing Fiber
Splice Protector
Table des matières
Autres manuels AFL Hyperscale Stockage
Manuels Stockage populaires d'autres marques
Spectra Logic
Spectra Logic T-Series Spectra T50e Manuel utilisateur
Panasonic
Panasonic LKM-F931-1 Manuel utilisateur
Tabernus
Tabernus Enterprise Erase E2400 Manuel utilisateur
Rocstor
Rocstor COMMANDER 3F series Manuel utilisateur
HP
HP P9000 Manuel utilisateur
Western Digital
Western Digital Ultrastar Data60 Manuel utilisateur