AETOOL OBDII Manuel utilisateur

AETOOL.com OBDII Scantool Manual

- 1 -

2%',,6&$1722/86(5·6

0$18$/



Table of Contents

1.0 -The

---

----

------

----

------

----

------

----

------

----

------

1.1 Main Unit ------------------------------------------------------------------------------------------------------------------ 2

1.2 Keypad Functions --------------------------------------------------------------------------------------------------- 3

1.3 Settings: Adjustments -------------------------------------------------------------------------------------------- 4-5

1.4 About ------------------------------------------------------------------------------------------------------------------------- 5

2.0 -Vehicle Diagnosis-------------------------------------------------------------------------------

2.1 START SCANNING------------------------------------------------------------------------------------------------ 5-8

2.1.1 - READ DTCs------------------------------------------------------------------------------------------------- 8

2.1.2 - ERASE DTCs----------------------------------------------------------------------------------------------- 9-10

2.1.3 - LIVE DATA---------------------------------------------------------------------------------------------------- 11

2.1.4 - FREEZE FRAME DATA------------------------------------------------------------------------------ 11

2.1.5 - MIL STATUS ------------------------------------------------------------------------------------------------ 12

2.1.6 - I/M READINESS------------------------------------------------------------------------------------------ 13

2.1.7 - VEHICLE INFORMATION (VIN)--------------------------------------------------------------- 15

2.2 LAST CODES --------------------------------------------------------------------------------------------------------- 16

2.3 Select M.F (Select Manufacturer) ----------------------------------------------------------------------- 18

–

Notic

e-------------------------------------------------

-----

---

----

-----

---

----

-----

3.1 Disclaimer ----------------------------------------------------------------------------------------------------------------20

4.0

– Warranty

Information--

---

4.1 Limited Warranty----------------------------------------------------------------------------------------------------- 20

4.2 Limitations of Warranty-------------------------------------------------------------------------------------------21

- 1 -

$(722/FRP  2 % ' ,,6&$172 2 / - 1 -

- 2 -

1.0 - The Scan Tool

1.1 - Main unit

Diagnostic Cable

DB15 Connector

Display

Keypad

- 2 - 2%',,6&$172 2 /

- 3 -

2%',,6&$1722/86(5·6

0$18$/



1.2 - Keypad Functions:

‘PWR’ key to start operation.

ENTER

ESC

HELP

‘ENTER’ key to confirm selection.

‘ESC’ key to exit and return to previous display.

HELP’ key for abbreviation query or info.

Page Up key for ‘next’ or scroll up

Page Down key for ‘previous’ or scroll down

- 3 -

$(722/FRP  2 % ' ,,6&$172 2 / - 3 -

- 4 -

1.3 - Settings: Adjustments

To enter the MENU Mode:

1、 Once the Scan Tool is powered up through the DLC

connection, the LCD screen lights up without any display.

Press key will wake up the display as below.

Note:

This is a safety feature that protects the scan tool from

power surge when plugged into the vehicles DLC.

2、 Press any key, it will switch to: “Car Manufacturer Logo “

3、 Press ENTER OR ESC key, the screen will enter

into: “New Scan” icon

4、Press key, to select: “Setting” icon as shown:

5、 Press ENTER key, the screen will enter into:

“Adjust Brightness” icon

6、 Press or key to increase or decrease the LCD Brightness

Contrast ranges from 1 to 10.

- 4 - 2%',,6&$172 2 /

- 5 -

2%',,6&$1722/86(5·6

0$18$/



7、 Once the brightness adjustment had been selected

to the desired setting, press

ENTER key to confirm

and exit back to the sub menu.

8、Press

ESC key to exit back to the main Menu.

1.4 - About

Enter the Setting Menu, press

confirm. ENTER key to

The screen will change to shown:

Press or key to select ‘About’ icon.

2.0 - Vehicle Diagnosis

2.1 - START SCANNING

- 5 - When everything had been confirmed and checked as mentioned in Getting Started, the

testing operation can be carried out.

$(722/FRP  2 % ' ,,6&$172 2 / - 5 -

- 6 -

1. Locate the vehicle Diagnostic Link Connector (DLC)

and make sure that the ignition switch is in OFF

position.

2. Connect the scan tool diagnostic connector to the

vehicle DLC.

If problem of inserting, rotate it to 180°

and try again

When the connection has been established, the LCD screen

lights up without any display.

Press key will wake up the display screen as

shown.

3. Press any key on the keypad will enter to select Car

Manufacturer logo as shown.

Now you can select the car manufacturer by pressing

the or key.

Press ENTER key to confirm and it will enter to the

screen as shown.

Now it is ready to do the scanning process if the

‘ENTER’ key is press again.

- 6 -

2%',,6&$172 2 /

- 7 -

2%',,6&$1722/86(5·6

0$18$/



4. If the car manufacturer logo is not correct and you

need to change it, then press or

key until icon.

Press ENTER key to enter; it will change back

to the car manufacturer logo.

Once the selection is confirmed, press this key again and it will return to the main

Menu.

7. To get ready for the scanning, use or

key to scroll to the ‘New Scan’ icon on the main Menu.

8. Turn the ignition key to ON. DO NOT start or crank

the engine.

9. Press the ENTER key once, the Scan tool will automatically starts to link up to the

- 7 -

vehicle’s computer and detects which type of communication protocol it is using.

10. After a few seconds, the screen will display the

menus as shown.

$(72 2 /FRP  2 % ' ,,6&$1722/ - 7 -

- 8 -

11. Now you can select the program from the menu by pressing or

key and confirm by ENTER key.

12. If the Scan tool fails to link up with the vehicle’s

computer, it will show a message as displayed on

the LCD screen:

Possible causes：

1. The Diagnostic connector is not connected properly.

2. Ignition Key is not turned ON.

3. The vehicle is not OBDII compliant.

Note:

To check whether the vehicle being tested is OBDII compliant, always

refer to the Vehicle Emission Control Information (VECI) decal located

under the

hood or by the radiator of most vehicles. See below).

2.1.1 – READ DTCs

✓ Selecting this function allows the Scan Tool to read the DTCs

from the vehicle’s control modules. DTCs are used to help

determine the

cause of a problem or problems within a vehicle. These codes cause the

control module to illuminate the malfunction indicator lamp

(MIL) when emission-related or drivability fault occurs. MIL

is also known as service engine soon or check engine lamp.

✓ READ DTCs can be done with the Key On Engine Off (KOEO)

or with the Key On Engine Running (KOER).

- 8 - 2%',,6&$172 2 /

Table des matières

Autres manuels AETOOL Instrument de mesure

AETOOL

AETOOL BESA 12 Manuel utilisateur

AETOOL

AETOOL BESA 11 Manuel utilisateur

AETOOL

AETOOL BESA-12P Manuel utilisateur

AETOOL

AETOOL GLOW PLUG ANALYSER Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur