AEG 11210 Manuel utilisateur
11210
INSTRUCTION MANUAL
- 1 -
Important Safety Instructions
When using an electrical appliance, basic safety precautions should always be followed, including the
following: Read all instructions before using your household sewing machine.
DANGER-To reduce the risk of electric shock:
Your household sewing machine should never be left unattended when plugged in. Always unplug your
machine from the electric outlet immediately after using and before cleaning.
Always unplug before changing lamp. Use a bulb 15 W max.
WARNING-to reduce: the risk of burns, fire, electric shock or injury to persons
- Do not allow to be used as a toy. Close attention is necessary when this sewing machine is used by or
near children.
- Use this machine only for its intended use as described in this manual.
- Never operate this sewing machine if it has a damaged cord or plug, if it is not working properly, if it
has been dropped or damaged or dropped into water. Return the sewing machine to the nearest
authorized dealer or service center for examination, repair, electrical or mechanical adjustment.
- If the supply cord that fixed with foot controller is damaged, it must be replaced by the manufacturer or
its service agent or a similar qualified person in order to avoid a hazard.
- Never operate the sewing machine with any air openings blocked. Keep ventilation openings of the
sewing machine and foot controller free from the accumulation of lint, dust and cloth.
- Never drop or insert any object into the opening.
- Do not use outdoors.
- Do not operate where aerosol (spray) products are being used or where oxygen is being administered.
- Do not put anything on the foot controller because the machine may accidentally start and the motor
or the foot controller may overheat.
- To disconnect turn all controls to the off position, then remove plug from outlet.
- Do not unplug by pulling on cord. To unplug, hold the plug, not the cord.
- Keep fingers away from all moving parts. Special care is required around the sewing needle.
- Always use the proper needle plate. The wrong plate can cause the needle to break.
- Do not use bent needles.
- Do not pull or push fabric while stitching. It may deflect the needle.
- Switch the machine off when making any adjustments in the needle area, such as threading needle,
changing needle or changing presser foot and the like.
- Always unplug the sewing machine from the electric outlet when making any user servicing mentioned
in the instruction manual.
- Use only identical replacement parts.
- This appliance is not intended for use by persons (including children) with reduced physical, sensory
or mental capabilities, or lack of experience and knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a person responsible for their safety.
- Children should be supervised to ensure that they do not play with the appliance.
SAVE THESE INSTRUCTIONS
Warning
When working close to the needle be very careful not to prick your fingers. When you use the machine
for the first time, put a piece of cloth under the presser foot und run the machine without thread for some
minutes. Dry any oil spots which may appear.
Please use for your sewing machine the ZHEJIANG FOUNDER presser foot, type KD-2902.
Power rating: 220 - 240V ~ , 50Hz
Current rating: 1.0A
Protection Class : II
The sound pressure level under normal operating conditions is 78dB (A).
- 2 -
CONTENTS
Name of parts...........................................................................................3-4
Accessories................................................................................................. 5
Before sewing (Power supply and sewing lamp).......................................... 6
Removing extension table ...........................................................................7
Free-arm sewing.......................................................................................... 7
Winding the bobbin......................................................................................8
Removing bobbin case and bobbin..............................................................9
Inserting bobbin into bobbin case................................................................9
Inserting bobbin case into shuttle race.......................................................10
Threading upper thread & Twin needle threading......................................11
Drawing up the bobbin thread....................................................................12
Changing sewing directions.......................................................................12
Levelling the machine................................................................................13
Adjusting thread tension ............................................................................14
Changing needle .......................................................................................15
Insert “darning plate“..................................................................................15
Fabric-Thread-Needle-table.......................................................................16
Sewing (pattern selector) and operation table............................................17
To start sewing..........................................................................................18
How to finish stitches.................................................................................19
Straight stitch.............................................................................................20
Zigzag sewing............................................................................................20
Automatic embroidery................................................................................20
Overcasting ...............................................................................................21
Straight and zigzag stretch stitches ...........................................................21
Blind stitch............................................................................................22-23
Button sewing............................................................................................24
Binding ......................................................................................................24
Zipper sewing............................................................................................25
Buttonhole sewing .....................................................................................26
Hemming...................................................................................................27
Twin needle...............................................................................................28
Embroidery................................................................................................28
Quilter........................................................................................................29
Seam guide ...............................................................................................29
Maintenance (Cleaning and oiling) ............................................................30
Checking performance problems-Troubleshooting ....................................31
- 3 -
NAME OF PARTS (FRONT VIEW)
1. Thread tension dial
2. Pattern selector dial
3. Bobbin winder stopper
4. Stitch length dial
5. Reverse button
6. Thread guide and needle clamp
7. Extension table
8. Shuttle cover
9. Presser foot
10. Face cover
11. Take up lever
12. Upper thread guide
2 3
4
5
6
7
8
9
1
10
11
12
- 4 -
REAR VIEW
1. Presser foot lever
2. Thumb screw
3. Needle plate
4. Spool pin (B)
5. Hand wheel
6. Spool pin (A)
7. Bobbin winder spindle
5
1
2
3
7
6
4
- 5 -
ACCESSORIES
Needle plate
screw driver
Screw driver
Zipper foot
Needle
Buttonhole cutter
Darning plate
Bobbin
(Use only original
plastic bobbins.)
Felt Zigzag foot
(on machine) Buttonhole foot
Spool pin (A)
Spool pin (B)
- 6 -
BEFORE SEWING
1. Fit plug into the machine.
2. Insert plug into the main socket.
3. Sewing speed can be varied by the foot
control.
Use only ZHEJIANG FOUNDER model
KD-2902 foot controller with sewing
machine.
.CAUTION: Please always unplug the power plug before you change the bulb or
perform maintenance work to the machine so that you prevent deadly
peril and electric shock.
Bulb replacement:
1. Open face cover in direction of arrow.
2. Remove bulb by unscrewing it
counter-clockwise.
3. Install a new bulb by screwing it in
clockwise.
4. Use a 15 watt bulb. (max)
Power supply / Power supply plug
Speed Controller
Power supply
Plug receptacle
machine plug
Sew lamp
- 7 -
REMOVING EXTENSION TABLE
Hold the left end of the table and pull it
out in direction of the arrow.
FREE-ARM SEWING
1. This sewing machine can be used as
a flat bed machine but easily converts
to a free arm machine by removing
the extension table.
2. Especially useful for sewing sleeves,
pant legs, tubular fabrics etc. more
easily.
3. To sew tubular items just slip the
sleeve or leg of pants on the free arm
as shown on the illustration.
- 8 -
5 cm thread
Clutch button
WINDING THE BOBBIN
Push bobbin winder spindle in direction of
the arrow. When bobbin winding is
completed, return spindle to its original
position.
When bobbin winding is incorrect, release
the screw of the upper thread guide and
adjust up or down until bobbin the
winding is balanced.
Correct
Screw
Winder spindle
1. Release by pushing clutch button to
bobbin and lock by pushing it to needle.
2. Push bobbin winder from left to right,
then it starts winding.
3. Push bobbin winder from right to left and
move clutch button to needle sign, then it
starts sewing.
- 9 -
REMOVING BOBBIN CASE AND BOBBIN
1. Raise the needle to its highest
position and open shuttle race cover.
3. Release the latch and the bobbin will fall out
easily.
INSERTINGBOBBININTOBOBBINCASE
1. Pull 5 cm of thread from bobbin and
insert it into bobbin case as shown.
3. Pull the thread through the slot and under the
tension spring and draw out about 10 cm of
thread.
2. Open the hinged latch of the bobbin
case and pull the bobbin case out of
the machine.
2. Guide the end of thread into the slot.
Slot
Hinged latch
5 cm
10 cm
Tension spring
Table des matières
Autres manuels AEG Machine à coudre
AEG
AEG NM 1800 Manuel utilisateur
AEG
AEG LAVATHERM 3200 Manuel utilisateur
AEG
AEG Favorit 123 Manuel utilisateur
AEG
AEG MICROMAT 110 Manuel utilisateur
AEG
AEG 63Z Manuel utilisateur
AEG
AEG Lavatherm 3500 Manuel utilisateur
AEG
AEG 11681 Manuel utilisateur
AEG
AEG 11681 Manuel utilisateur
AEG
AEG 11680 Manuel utilisateur
AEG
AEG 11225 LCD Manuel utilisateur
AEG
AEG AEG2379 Manuel utilisateur
AEG
AEG 791 Manuel utilisateur
AEG
AEG NM-1714A Manuel utilisateur
AEG
AEG 112704 Manuel utilisateur
AEG
AEG Spirit 100 Manuel utilisateur
AEG
AEG 65Z Manuel utilisateur
AEG
AEG 30Z Manuel utilisateur
AEG
AEG 225/7 LCD Manuel utilisateur
AEG
AEG NM 1714 Manuel utilisateur
AEG
AEG 713 Manuel utilisateur
