AEG Electrolux DD 8793 Fiche technique

DD 8793

Cooker Hood

Cappa aspirante

Campana extractora

Exaustor

Operating and Installation Instructions

Istruzioni di montaggio ed uso

Instrucciones de montaje y manejo

Manual de Instruções

Contents

Safety warnings 4

for the user 4

for the installer 4

Description of the Appliance 6

Extractor version 6

Filter Version 6

Hood Operation 8

Switching on the hood 8

Switching on the light 8

Control device for grease or charcoal filter 8

Led signal for grease filter 8

Led signal for charcoal filter 8

Resetting the saturation indicator 8

Using the Re ote Control 9

Re ote Control Maintenance 9

Maintenance and care 10

Metal grease filter 10

Open the etal grease filter 10

Charcoal filter 11

Changing the light bulb 12

Cleaning 13

Special accessories 13

echnical assistance service 13

Guarantee conditions 14

echnic Details 15

Mounting accessories included 15

Electrical connection 16

Safety warnings for the electrician 16

Wall unit ounting 17

Safety warnings

For the user

 The cooker hood is designed to extract unpleasant odours fro the

kitchen, it will not extract stea .

 Always cover lighted ele ents, to prevent excess heat fro

da aging the appliance. In the case of oil, gas and coal fired

cookers it is essential to avoid open fla es.

 Also, when frying, keep the deep frying pan on the cooker top/cooker

under careful control.

 The hot oil in the frying pan ight ignite due to overheating.

 The risk of self-ignition increases when the oil being used is dirty.

 It is extre ely i portant to note that overheating can cause a fire.

Never carry out any flambé cooking under the hood.

Always disconnect the unit from the power supply before

carrying out any work on the hood, including replacing the

light bulb (take the cartridge fuse out of the fuse holder or switch off

the auto atic circuit breaker).

It is very important to clean the hood and replace the filter at

the recommended intervals. Failure to do so could cause

grease deposits to build up, resulting in a fire hazard.

 The appliance is not intended for use by young children or infir

persons without supervision.

 Older children ust be supervised if using the appliance.

 Young children should be supervised to ensure that they do not play

with the appliance.

 WARNING - Ensure that the appliance is switched off before

replacing the la p to avoid the possibility of electric shock.

This appliance is arked according to the European directive 2002/96/

EC on Waste Electrical and Electronic Equip ent (WEEE).

By ensuring this product is disposed of correctly, you will help prevent

potential negative consequences for the environ ent and hu an health,

which could otherwise be caused by inappropriate waste handling of

this product.

The sy bol on the product, or on the docu ents acco panying

the product, indicates that this appliance ay not be treated as

household waste. Instead it shall be handed over to the applicable

collection point for the recycling of electrical and electronic equip ent.

Disposal ust be carried out in accordance with local environ ental

regulations for waste disposal.

For ore detailed infor ation about treat ent, recovery and recycling

of this product, please contact your local city office, your household

waste disposal service or the shop where you purchased the product.

For the installer

 When used as an extractor unit, the hood ust be fitted with a hose

having preferably the sa e dia eter as the outlet hole.

Attention: The hose is not supplied and ust be purchased

separately.

 Should there already be a pipe of dia eter 125 that ducts to the

outside through the walls or roof, it is possible to use the 150/125

reduction flange provided. In this case the hood will be slightly

ore noisy.

 When installing the hood, make sure you observe the following

minimum distance from the top edge of the cooking hob/ring

surfaces:

electric cookers 600 mm

gas cookers 650 mm

If the instructions for installation for the gas hob specify a greater

distance, this ust be adhered to.

 The national Standard on fuel-burning syste s specifies a axi u

depression of 0.04 bar in such roo s.

 The air outlet ust not be connected to chi ney flues or co bustion

gas ducts. The air outlet ust under no circu stances be connected

to ventilation ducts for roo s in which fuel-burning appliances are

installed.

 The air outlet installation ust co ply with the regulations laid down

by the relevant local authorities.

 When the unit is used in extraction ode, a sufficiently large

ventilation hole ust be provided, with di ensions that are approxi-

ately the sa e as the outlet hole.

 National and regional building regulations i pose a nu ber of

restrictions on using hoods and fuel-burning appliances connected to

a chi ney, such as coal or oil roo -heaters and gas fires, in the

sa e roo .

 Hoods can only be used safely with appliances connected to a

chi ney if the roo and/or flat (air/environ ent co bination) is

ventilated fro outside using a suitable ventilation hole approxi ately

500-600 c 2 large to avoid the possibility of a depression being

created during operation of the hood.

 If you have any doubts, contact the relevant controlling authority or

building inspectors office.

 Since the rule for roo s with fuel burning appliances is outlet hole of

the sa e size as the ventilation hole, a hole of 500-600 c 2, which

is to say a larger hole, could reduce the perfor ance of the extractor

hood.

 If the hood is used in its recirculation ode, it will operate si ply and

safely in the above conditions without the need for any of the

afore entioned easures.

 When the hood is used in its extraction ode, the following rules

ust be followed to obtain opti al operation:

- short and straight outlet hose

- keep bends in outlet hose to a ini u

- never install the hoses with an acute angle, they ust always

follow a gentle curve.

- keep the hose as large as possible (preferably the sa e dia eter

as the outlet hole).

- the length should be no ore than:

3 etres with one 90° bend

2 etres with two 90° bends

Bends of ore than 90° will reduce the efficiency of the hood and

reduce the airflow.

 Failure to observe these basic instructions will drastically reduce the

perfor ance and increase the noise levels of the extractor hood.

Description of the Appliance

he cooker hood is designed to extract

unpleasant odours from the kitchen, it

will not extract steam.

 The hood is supplied as an extractor unit

and can also be used with a recirculation

ode by fitting a charcoal filter.

Extraction mode

 In this ode fu es are extracted to the

outside via a hose connected to the

coupling ring D. Fig. 1.

 In order to obtain the best perfor ance the

hose should have a dia eter equal to the

outlet hole.

Should there already be a pipe of dia eter

125 that ducts to the outside through

the walls or roof, it is possible to use the

150/125 reduction flange provided. In

this case the hood will be slightly ore noisy.

Recirculation mode

 The air is filtered through a charcoal filter

and returned to the kitchen.

 You will need an original charcoal filter for the

recirculation ode. (See Special

Accessories).

Assemble the deflector (3 parts): the three

parts ust be fixed with 2 screws Ø 3.5 13

, the extension of the deflector is

adjustable and ust correspond to the width

of the chi ney flue support, to which it ust

be fixed.

Fix the deflector using 4 screws Ø 2,9x6.5

. Fig. 2.

 Optionally, the position of the chi ney

ele ents can be changed.

When using the hood in the filter version the

chi ney ust be fixed at the top, with the air

outlet grill at the side.

Fig. 1

Fig. 2

Control Panel

 Best results are obtained by using a low speed for nor al conditions

and a high speed when odours are ore concentrated.

Turn the hood on a few inutes before you start cooking.

The hood should be left on after cooking for about 15 inutes or until

all the odours have disappeared.

 The hood operation ay be controlled via the control ball or with the

re ote control.

Every status change (changing speed, switching on the lights, etc.)

and is recognizable fro the variation of light e itted by the control

ball and by an acoustic signal.

he control ball serves also as a light signal :

No signal :

The hood is switched off.

Static green light :

Hood is switched on at power level 1 ( ini u ).

Static orange light :

Hood is switched on at power level 2 ( ediu ).

Static red light :

Hood is switched on at power level 3 ( axi u ).

Alternating red light :

Hood is switched on at intensive power level (ti ed at 5 inutes)

Alternating green light :

Indicates the grease filter saturation - clean the grease filter

Alternating orange light :

Indicates the charcoal filter saturation - clean or replace the

charcoal filter

Attention!

The control Ball flashes orange to indicate the saturation of the odor

filter even when the charcoal filter is not installed inside the cooker

hood.

However perfor the signal reset operation as follows: select the

intensive speed (the control ball lights up with a red flashing light),

depress again and hold depressed for about 3 seconds until a bip

sound indicates the reset.

Switching on the hood - Fig. 3

The control ball is a balancer switch.

Depressing the control ball

repeatedly towards the right

switches on the hood and you ay

select the suction level desired,

depressing once again on the right

the hood switches off.

Switching on the light -

Fig. 3

Depress the control ball towards the

left :

once for sub ersed lighting,

once again for full lighting,

depress again to switch off the light.

Control device for grease or charcoal filter

The air duct, in this hood, is provided with a device that signals when

the filter requires cleaning or changing .

Led signal for grease filter

The LED signal flickers (flickering green light) when the grease filter

requires cleaning, occurs at about 40 operating hours.

Carefully note the device for grease filter aintenance!

Led signal for charcoal filter

The LED signal flickers (flickering orange light) when the charcoal filter

requires cleaning or replacing, occurs at about 160 operating hours.

Carefully note the device for charcoal filter aintenance!

Resetting the saturation indicator

After cleaning or replacing the filter, select the intensive speed (the

control ball lights up with a red flashing light), depress again and hold

depressed for about 3 seconds until a bip sound indicates the reset.

depress

towards the

right to switch

on the hood

depress

towards the

left to switch

on the light.

Fig. 3

Using the Remote Control

The re ote control ay operate in hu id

environ ents, but not when placed on wet

surfaces.

Selecting the Suction Speed position the

re ote control vertically near the cook top area

and rotate clockwise to increase the suction

speed, and anticlockwise to decrease the suction

speed.

Turning on the Light, press the re ote control

fro the top downwards once for suffused lighting,

again for full lighting, and again to turn off the light.

Remote Control

Maintenance

Clean the re ote control using non

abrasive detergents.

Follow the instructions below in order

to replace the batteries for the re ote

control :

- Using a s all screwdriver, raise the

cover on the base of the re ote

control, in order to access the battery

co part ent.

Re ove the battery holder, and

replace 4 new batteries type ..394 of

1.5V.

Place the batteries in order in the battery holder (see Fig. 5) taking care

to respect the polarities indicated on the base of the upper section of

the re ote control.

Warning!

If the re ote control doesnt work after installation (yet the control ball

works correctly), do the following:

1. Place the re ote control on the work surface near the hood.

2. Disconnect the hood fro the ains.

3. Reconnect the hood to the ains.

Follow this procedure whenever the re ote control doesnt work for no

apparent reason (e.g.: dead battery).

Fig. 4

Fig. 5

Maintenance and Care

he hood must always be disconnected from the electricity

supply before beginning any maintenance work.

Metal grease filter

 The purpose of the grease filters is to absorb grease particles which

for during cooking and it must always be used, either in the

external extraction or internal re-circulation function.

Attention: the etal grease filters ust be re oved and washed,

either by hand or in the dishwasher, every four weeks.

Removing the metal grease filter

 First, push the etal grease filter stop backwards, then extract the

filter, pulling downwards. Fig. 6.

Hand washing

Soak grease filters for about one hour

in hot water with a grease-loosening

cleaner, then rinse off thoroughly with

hot water. Repeat the process if

necessary. Refit the grease filters

when they are dry.

Dishwasher

Place grease filters in the dishwasher.

Select ost powerful washing

progra e and highest te perature,

at least 65°C. Repeat the process.

Refit the grease filters when they are

dry.

When washing the etal grease filter

in the dishwasher a slight

discolouration of the filter can occur,

this does not have any i pact on its

perfor ance.

 Clean the inner housing using a hand

hot solution only(never use caustic

detergents, abrasive powders or brushes).

Fig. 6

Table des matières

Autres manuels AEG Electrolux hotte de ventilation

AEG Electrolux

AEG Electrolux DM8600 Manuel utilisateur

AEG Electrolux

AEG Electrolux DI9611-M Manuel utilisateur

AEG Electrolux

AEG Electrolux DD8623 Fiche technique

AEG Electrolux

AEG Electrolux 502 D Fiche technique

AEG Electrolux

AEG Electrolux DI9814 Manuel utilisateur

AEG Electrolux

AEG Electrolux DD9996-B Manuel utilisateur

AEG Electrolux

AEG Electrolux DL8560-M Manuel utilisateur

AEG Electrolux

AEG Electrolux DD6660-M Manuel utilisateur

AEG Electrolux

AEG Electrolux HD 8795 Fiche technique

AEG Electrolux

AEG Electrolux DU 4561 Manuel utilisateur

AEG Electrolux

AEG Electrolux DF7460 Fiche technique

AEG Electrolux

AEG Electrolux DD 8696 Fiche technique

AEG Electrolux

AEG Electrolux DD 8625 Manuel utilisateur

AEG Electrolux

AEG Electrolux HI 8610 Fiche technique

AEG Electrolux

AEG Electrolux DF7190 Manuel utilisateur

AEG Electrolux

AEG Electrolux DU 4561 Fiche technique

AEG Electrolux

AEG Electrolux DD 8821 Fiche technique

AEG Electrolux

AEG Electrolux HE 3160 Fiche technique

AEG Electrolux

AEG Electrolux Cooker hood Manuel utilisateur

AEG Electrolux

AEG Electrolux HC 3360 Guide produit

AEG Electrolux

AEG Electrolux DD 9864 Manuel utilisateur

AEG Electrolux

AEG Electrolux DD 8697 Fiche technique

AEG Electrolux

AEG Electrolux DD6460-M Manuel utilisateur

Manuels hotte de ventilation populaires d'autres marques

emmeti

emmeti RECUPA MED A-140 Mode d’emploi

Nibe

Nibe F135 Manuel utilisateur

Kuppersberg

Kuppersberg INTRO 60 Instructions d'installation et d'entretien

Zephyr

Zephyr Spruce AK9834BS Guide d'installation

Hisense

Hisense MH6INBG Manuel utilisateur

Miele

Miele DA 1255 Manuel utilisateur

Broan

Broan 46000 Manuel utilisateur

GE Profile PV977 Instructions originales

FALMEC

FALMEC FFRIA24W5FS Manuel utilisateur

Whirlpool

Whirlpool RH2600XL-1 SERIES Manuel utilisateur

Küppersbusch

Küppersbusch DX ISLA Manuel utilisateur

ETNA

ETNA AV360RVS Manuel utilisateur

JUNO

JUNO JDF603E6 Manuel utilisateur

Miele

Miele DA 6708 D Manuel utilisateur

Tricity Bendix

Tricity Bendix LE 150 Manuel

AEG

AEG X68163BV1 Manuel utilisateur

AEG

AEG 125 D Manuel utilisateur

Smeg

Smeg KSEV97X Manuel utilisateur