Advent CAM430MV Manuel utilisateur
Model: CAM430MV
Wired Multi-View Camera with
License Plate / Rear Surface Mount
Installation Manual
Features
Fully Adjustable, Multiple Viewing Angle Smart Camera.
High Resolution, 1/2” CMOS Color Camera
Weatherproof Housing
190 Degree Wide View Angle
Built in Microphone
Selectable Image: Normal/Top Down /Panoramic/Side or Corner
Multiple Camera Mounts including Behind License Plate –Does Not
Obstruct Plate
2
Table of Contents
Warnings......................................................................................3
Product Description .....................................................................4
Packing List .................................................................................4
Operating Instructions..................................................................5
Camera Installation Instructions ..................................................8
Camera Wiring Diagram............................................................12
Software Configuration Settings................................................14
Specifications ............................................................................19
Troubleshooting.........................................................................19
Warranty ....................................................................................20
3
Warnings
The product is intended to assist in safe driving and to allow the driver to
have a broader rear view while the vehicle is in reverse. You, as the
driver, are solely responsible for the safe operation of your vehicle and
the safety of your passengers according to local traffic regulations. Do not
use any features of this system to the extent it distracts you from safe
driving. Your first priority while driving should always be the safe
operation of your vehicle. Audiovox Electronics Corporation cannot
accept any responsibility whatsoever for accidents resulting from failure
to observe these precautions or safety instructions.
This product utilizes high voltage. Any unauthorized modifications or
damage to the product may result in electrical shock. Handle all
components with care. Inspect regularly for damage to components and
cabling.
You are responsible for ensuring that the installation of this product does
not void or affect the vehicle manufacturer’s warranty. Audiovox
Electronics Corporation or its subsidiaries are not liable in full or in part
for improper installation resulting in loss or damage to your property, or
for voiding all or part of the vehicle manufacturer’s warranty.
Do not apply excessive force to any of the components contained within
this kit. Excessive force used before, during or after installation that
results in a damaged or non-functional part will void all warranties.
Please follow the procedures in this installation manual. Improper
installation or modification of this product will void all warranties.
4
Product Description
This revolutionary camera uses machine vision technology and an
advanced megapixel imager to allow you to choose between different
viewing angles to get the optimum rear viewing experience.
The system also includes a built in microphone so you can hear any
warnings or noises from outside the vehicle if your monitor supports
audio.
The camera is easy to mount on your car, truck, or van with the bracket
being hidden by your license plate. We have also included a surface
mount bracket to help with other installation methods. This wired Camera
is compatible with most monitors/TFT screens and can be connected
using a standard RCA connector.
The system includes a control button to allow you to configure the camera
to suit your requirements and to switch between 4 different viewing
angles.
Packing List
Part
Part #
QTY
Camera Module
31562040
Power Cable and Installation Kits
30192160
Switching cable
31562170
Optional mounting bracket
31562060
Installation Kits
31562010
Manual
31562020
5
Operation Instructions
1. Turning the camera on
Place the gear from neutral to reverse position.
2. Change the camera view
Press the MODE button
The view changes each time when MODE
button is pressed. The image will return to
the default image next time the vehicle is
placed in reverse gear.
Panoramic View
Rear View
Top View
Side View
6
Panoramic view: A wide angle field of view behind the car.
Rear view: An undistorted view for reversing to parking area.
Top view: Provide a undistorted top down perspective.
Side view:
Provide a divided image left and right perspectives in one view. Like
looking up and down the street.
7
Changing the Image View Order & Default
You can decide which view comes up as your default view and you can
also change what order the views are seen when you press the MODE
button.
Whenever you hold down the MODE button for 5 seconds the current
view becomes the default view –all other views are moved down in the
order. This symbol comes on screen to confirm the change:
EXAMPLE:
So if you wanted to use “Rear View” as your default view and “Side
View” as your 2nd choice then you would:
1. Place the vehicle in reverse.
2. Press MODE button to cycle to “Side View”
3. Hold MODE button for 5 seconds.
4. Go out of reverse
5. Place the vehicle in reverse
6. Press MODE button to cycle “Rear View”
7. Hold MODE button down for 5 seconds.
8. Now whenever you go into reverse gear the “Rear view” will
come up automatically and the first time you change MODEs you
will always get “Side View”
8
Camera Installation
License Plate Mounting Instructions
1) Remove the rear license plate.
Examine the vehicle to determine the best way to run the power wires to
the reverse lights and the extension cable through the car.
The Camera can be mounted above or below the plate. (For surface
mounting with the included bracket, see the next section.) Determine the
mounting location that best suits your needs. Be sure to verify that your
installation plan complies with local laws and requirements. Most states
require that the state name, registration stickers, and license number are
not obstructed in any way.
Place the camera bracket behind the license plate and line up the holes.
Fasten the camera mounting bracket and the license plate to the vehicle
using the anti-theft screws provided. After installation of screws with the
tool provided, place the tool in the glove compartment or other safe place
for future use.
NOTE: If you decide to mount the camera at the bottom of the license
plate, you must first remove the screw that holds the camera to the
bracket and flip the camera over so the picture will not be displayed up-
side down.
9
Route the camera wiring into the vehicle. The wire can be run through an
existing grommet, behind a tail lamp, under the trunk molding, or if
necessary, through a 5/8 inch hole drilled near the vehicle’s rear license
plate. When choosing a wiring path, make sure the cable will not be
damaged or pinched, as this may cause a short circuit that is not
covered by the warranty. If drilling a hole, perform the following steps:
a) Acquire a 5/8 inch drill bit, rust preventive, all of which can be
purchased at a hardware store.
b) Check behind the intended drilling location before drilling to
verify that no wires or mechanisms can interfere with or be
damaged during drilling.
c) Check for interference with license plate lights and the hatch
release switch and/or mechanism.
d) Drill a 5/8 inch hole at the selected location.
e) Coat the edge of the hole with rust preventative.
f) Route the camera cable through the grommet and then through
the hole.
g) Insert the grommet in the hole to keep water from entering the
vehicle.
h) Adjust camera angle so that in standard reversing views you can
see a small piece of the bumper and then tighten the mounting
screws.
10
Surface Mounting Instructions
2) Find a suitable location on the vehicle where the bracket will not
interfere with any equipment or doors, or block the line of sight.
Verify that the planned mounting location is accessible from behind
and that you have access to route the wiring inside the vehicle. Be
sure that the mounting screws will not hit any wires or equipment
inside the vehicle.
3) Attach the surface mounting bracket to the vehicle with the hardware
included.
4) Route the camera wiring into the vehicle. The wire can be run through
an existing grommet, behind a tail lamp, under the trunk molding, or
if necessary, through a 5/8 inch hole drilled near the vehicle’s rear
license plate. When choosing a wiring path, make sure the cable
will not be damaged or pinched, as this may cause a short circuit
that is not covered by the warranty. If drilling a hole, perform the
following steps:
a) Acquire a 5/8 inch drill bit, rust preventive, and a 5/8 inch rubber
grommet, all of which can be purchased at a hardware store.
b) Check behind the intended drilling location before drilling to
verify that no wires or mechanisms can interfere with or be
damaged during drilling.
c) Check for interference with license plate lights and the hatch
release switch and/or mechanism.
d) Drill a 5/8 inch hole at the selected location.
Table des matières
Autres manuels Advent Caméra embarquée
