Advantech PPC-L60T Manuel utilisateur

Panel PC user’s Manual ed1

PPC-L60T

VIA Eden Processor-based Fanless Panel PC

with 6.4 TFT LCD.

Contents

Chapter 1 General information

Chapter 2 System Setup

Chapter 3 Jumper Setting and Connectors

Chapter 4 Hardware Installation and Upgrading

Chapter 5 Mounting Instructions

Chapter 1 General information

1.1 Introduction

The PPC-L60T panel PC is a VIA low-power Eden processor

computer that is designed to serve as a human machine interface

(HMI) and as a multimedia computer. It is a PC based system with

6.4” color TFT LCF display and. Stainless enclosure, the

PPC-L60T is as compact and user friendly as a multi-function

computer.

For system integrators, this simple, complete, compact and high

integrated multimedia system lets you easily build a panel PC into

your application. Common industrial applications include factory

automation systems, precision machinery, and production process

control. It is also suitable for many nonindustry applications,

including car park automation and interactive Kiosk system. Our

Panel PC is a reliable, cost effective solution to your application’s

processing requirements.

1.2General Specifications

General

zDimensions(WxHxD): 218x151x74.2 mm (8.58"X5.94"X2.92 ")

zWeight:1.8 kg (6.6 Ibs)

zPower supply: ATX type

Input Voltage: 12Vdc -24 Vdc, 3.5A max.

Output Voltage: 5V@5A, 12V@1A

zPower adaptorAC/DC

Input Voltage: 100~240V ac

Output Voltage:[email protected]

zDisc Driver housing: Space for one 2.5”HDD.

zFront Panel: IP65/NEMAcompliant.

Standard PC functions

zCPU: Onboard VIAEden™ 400 MHz processor

zBIOS: Award 256 KB Flash BIOS.

zSystem Chipset: VIA PN 133T Chipset

zFront Side bus:133 MHz

z2nd level cache: 64 KB on the Eden processor.

zSystem Memory: One 144-pin SODIMM socket up to 512

MB SDRAM

zSeries ports: Two serial ports with two-232 ports, one is

RS232 ports; the other is RS-232/422/485 port. All ports are

compatible with 16C550UARTs, +5V/+12V power supply

selectable.

zUniversal serial bus (USB port: Support up to one USB port

and Intel UHC1v1.1 compatible.

zSSD: Built in Type 1 Compact Flash socket, supports

Compact Flash card shared with one IDE channel.

zWatchdog timer: 62-level, internal 1~62 seconds.

Automatically generates system reset or IRQ11 when the

system stops due to a program error or EMI. Jumperless

selection and software enabled/disabled.

Battery: 3.0V @ 195 Ma lithium battery

Audio function

Chipset: VIA82C686 South Bridge.

Audio controller: AC 97 Ver.2.0 compliant interface, Multi

stream direct sound and Direct Sound 3D acceleration.

Stereo Sound: 18 bit full-duplex codes.

Touch screen function:

Type AnalogResistive

Resolution Continuous

Light Transmission 80%

Controller USBinterface

Software Driver Support Windows® 98/2000/XP

Durability 10million

(Touch in a lifetime)

Optional modules

Memory: up to 512 MB SDRAM (Standard is built-in 128 MB)

HDD: 2.5” HDD.

Operating System: Windows®

98/2000/XP/XPE/WinCE.NET4.2

Environmental Specifications

zOperating Temperature 0-40° C

zRelative Humidity 10~95% @ 40° C

(non-condensing)

zShock(Operating) 10G peak acceleration (11

ms.duration)

zVibration 1G

zEMC CE,FCCClassA

zSafety CE,UL

zFront Panel Protection IP 65/ NEMA compliant

1.3 LCD specifications

zDisplay Type 6.4” TFT LCD

zMax. Resolution 600 X480

zColors 262K

zDot Size(mm) 0.203 x 0.203

zViewing Angle 90°

zLuminance 150 cd/m2

zTemperature 50°C

zBacklight Lifetime 20,000hrs

Note: The color LCD display installed in the Panel PC is

high-quality and reliable. However, it may contain a few defective

pixls which don’t always illuminate. With current technology, it is

impossible to completely eliminate defective pixles. Advantech is

activity working to improve this technology.

Chapter 2 System Setup

2.1 AQuick Tour of the Panel PC

Before you start to set up the Panel PC, take a moment to become

familiar with location and purpose of the controls, driver,

connectors and ports, which are illustrated in the figures as below.

When you place the Panel PC upright on the desktop, its front

panel appears as shown

in the Figure 2-1.

When you turn the panel PC around and look at its rear cover, you

will find the I/O section as shown in Fig.2-2. (The I/O section

includes various I/O ports, including serial ports, the Ethernet port,

USB port, VGAport and so on.)

2.2 Installation Procedures

2.2.1 Connecting the power Cord

The Panel PC can only be powered by a DC electrical outlet

12~24 voltage, Max 3.5A). Be sure to always handle the power

cord by holding the plug ends only. Please connect the male plug

of the power cord to the DC inlet of the Panel PC.

2.2.2 Connecting the keyboard or mouse.

Connect the PS/2 mouse and keyboard port on the I/O section of

the Panel PC.

2.2.3 Switch on the power

Switch on the power switch on the rear cover.

2.3 Running the BIOS setup program

Your Panel PC is likely to have been the properly set up and

configured by your dealer prior to delivery. You may still find it

necessary to use the Panel PC’s BIOS (Basic Input-Output System)

setup program to change system configuration information, such

as the current date and time or your type of the hard drive. The

setup program is stored in ready-only memory (ROM).It can

either be accessed when you turn on or reset the panel PC, By

pressing the “ Del” Key on your keyboard immediately after

running the computer on.

The settings you specify with the setup program are recorded in s

special area of memory called CMOS RAM. This memory is

backed up by a battery so that it will not be erased when you turn

off or reset the system. Whenever you turn on the power, the

system reads the setting stored in CMOS RAM and compares

them to the equipment check conducted during the power on

self-test (POST).If an error occurs, an error message will be

displayed on screen, and you will be prompted to run the setup

program.

2.4 Installing the system software

Recent release of operating systems include setup program which

automatically load and guide you through hard disk preparation

and operating system installation. The guidelines below will help

you determine the steps necessary to install your operation system

on the Panel PC hard drive.

Note: Some distributors and system integrators may have already

pre-installed system software prior to shipment of your Panel PC.

Installed software requires an installed HDD. Software can be

loaded in the PPC-L60T using any of two methods.

2.4.1 Method 1: Use the Ethernet

You can use the Ethernet port to download software to the HDD.

2.4.2 Method 2: Use the COM

You can use the Lap Link 6 or similar transmission software.

Connect another PC to the PPC-L126 with an appropriate cable

and transmit the software to the PPC-L126.

2.5 Installing the Drivers

After installing your system software, you will be able to set up

the Ethernet, VGA, audio, and touch screen functions. All drivers

are stored in a CD-ROM disc entitled “Divers and Utilities” which

can be found in your assembly box.

The various drivers and utilities in the CD-ROM disc have their

own test files which help users install drivers and understand their

functions. These files are a very useful supplement to the

information in this manual.

Note: The drivers and utilities used for the PPC-L60T Panel PCs

are subject to change without notice. IF in doubt, check

Advantech’s website or contact our application engineers for the

latest information regarding drivers and utilities.

Chapter 3 Jumper Setting and Connectors.

3.1 Jumpers

The motherboard of the PPC-L60T has

a number

jumpers that

allow

you to configure your system to suit

your

application. The

table

below lists the

functions of

the various jumpers.

Table 3.1:

Jumpers

Label Function

S1 Panel type select

S2 CMOS clear button

S3 System reset button

JP1 COM2 RS232/422/485 & WDT setting

3.2 Connectors

On-board connectors link the PPC-L60T to external devices

such as hard disk drives,

a keyboard, or

floppy drives.

The

table below

lists

the func- tion

of each of the board’s

connectors.

Table 3.2:

Connectors

Label Function

CN1 ATX feature

CN2 CPU fan power

CN3 Ext. flat panel

CN4 Flat panel connector

CN5 LCD Inverter control connector

CN6 LVDS connector

CN7 Main Power connector

CN8 ATX power on/off switch connector

CN9 Peripheral power connector (-5V, -12V)

Table des matières

Autres manuels Advantech Écran tactile

Advantech

Advantech RUGGED PENTIUM IPPC-9120 Manuel utilisateur

Advantech

Advantech PPC-3151W Manuel utilisateur

Advantech

Advantech PPC-415 Manuel d'installation et d'exploitation

Advantech

Advantech PPC-100 Manuel utilisateur

Advantech

Advantech TPC-1251T-Exxx Series Manuel utilisateur

Advantech

Advantech PPC-L106T Manuel utilisateur

Advantech

Advantech PPC-3100-RE9A Manuel utilisateur

Advantech

Advantech TPC-1582H Manuel utilisateur

Advantech

Advantech PPC-6151C Manuel utilisateur

Advantech

Advantech PPC-6151C Manuel utilisateur

Advantech

Advantech PPC-177T Manuel utilisateur

Advantech

Advantech SPC-200 Series Manuel utilisateur

Advantech

Advantech HMI-640S Manuel utilisateur

Advantech

Advantech IPPC-6152F Series Manuel utilisateur

Advantech

Advantech PPC-L128T Manuel utilisateur

Advantech

Advantech PPC-112W Manuel d'installation et d'exploitation

Advantech

Advantech PPC-3100S Manuel utilisateur

Advantech

Advantech PPC-120 Manuel utilisateur

Advantech

Advantech IPPC-6152 Series Manuel utilisateur

Advantech

Advantech PPC-3100-RE9A Manuel d'installation et d'exploitation

Advantech

Advantech IPPC-6152A Manuel utilisateur

Advantech

Advantech TPC-1261H Manuel utilisateur

Advantech

Advantech PPC-3210SW Manuel utilisateur

Advantech

Advantech UTC-307GP-ATB0E Manuel d'installation et d'exploitation

Manuels Écran tactile populaires d'autres marques

FlowLine

FlowLine Data loop Manuel utilisateur

ALPEX

ALPEX AEx-8 P Series Manuel utilisateur

Ltech

Ltech E5S Manuel utilisateur

Harman

Harman AMX MODERO S MSD-701-L2 Manuel utilisateur

Acnodes

Acnodes PC 1150 Manuel utilisateur

AIS

AIS IP10IA99 series Manuel utilisateur

IBASE Technology

IBASE Technology ASTUT-152-RE1S Manuel utilisateur

YASKAWA

YASKAWA TP 610C Manuel utilisateur

B&R

B&R Power Panel C Series Manuel utilisateur

Beijer Electronics

Beijer Electronics X2 control Manuel utilisateur

AXIOMTEK

AXIOMTEK GOT321W-521 Manuel utilisateur

TRIDONIC.ATCO

TRIDONIC.ATCO x-touchBOX Manuel utilisateur

Qomo

Qomo QIT1386 Manuel utilisateur

DFI

DFI KS104-CD Manuel utilisateur

AMX

AMX AXP-PPC Mode d’emploi

Sartorius

Sartorius X3 PR 5410 Manuel utilisateur

AMX

AMX Modero X Series Manuel utilisateur

B&R Industries

B&R Industries MAPPC900-ENG Manuel utilisateur