Advantech MIC-770 Manuel d'installation et d'exploitation
MIC-770 Startup Manual 1
Before you begin installing your card, please make sure
that the following items have been shipped:
1. MIC-770 bare-bone system x 1
2. Startup manual EN\CN\TC for MIC-770 1st Ed
P/N: 2041077000
3. 4-pin Phoenix connector P/N: 1652003234
4. Mounting bracket x2 P/N: 1960070543T001
5. SATA cable x1 P/N: 1700013095
6. SATA power cable x 1 P/N: 1700024372-01
If any of these items are missing or damaged, please con-
tact your distributor or sales representative immediately.
Note: Acrobat Reader is required to view any PDF file.
Acrobat Reader can be downloaded at: get.
adobe.com/reader (Acrobat is a trademark of
Adobe)
MIC-770
Intel
®
8
th
Generation Core™ i Socket Compact
Fanless Computer
Startup Manual
Caution:
DANGER OF EXPLOSION IF BATTERY IS INCOR-
RECTLY REPLACED. REPLACE ONLY WITH THE
SAME OR EQUIVALENT TYPE RECOMMENDED
BY THE MANUFACTURER, DISCARD USED BAT-
TERIES ACCORDING TO THE MANUFACTURER’S
INSTRUCTIONS.
Attention:
DANGER D’EXPLOSION SI LA BATTERIE EST
INEXACTEMENT REMPLACÉE. REMPLACEZ
SEULEMENT AVEC LA MÊME CHOSE OU LE TYPE
ÉQUIVALENT RECOMMANDÉ PAR LE FABRICANT,
JETTENT LES BATTERIES UTILISÉES INSTRUC-
TIONS DE S SELON FABRICANT DES’.
Processor System
•Intel®8th generation Core™ i socket CPU (LGA1151)
Memory
•Supports dual channel DDR4 SODIMM-2666 MHz,
16 GB per slot without ECC function; Max. capacity
is 32GB
Graphics
• Q370: Intel®HD Graphics 630, supports DirectX 12
• H310: Intel®HD Graphics 610, supports DirectX 12
Serial Ports
•2 x RS-232/422/485, RS-485 supports automatic flow
control
Ethernet
• Interface: 10/100/1000 Mbps
• Controller:
Q370 LAN1: Intel®I219LM, LAN2: Intel®i210IT
H310 LAN1: Intel®I219V, LAN2: Intel®i210IT
Storage
• Internal 2.5” Storage Bay: 1
• mSATA: 1
Front I/O
• Display: 1 x VGA, 1 x HDMI
• USB: Q370: 2 x USB3.1 , 6 x USB3.0
H310: 4 x USB 3.0 and 4 x USB 2.0
• Serial: 2 x RS-232/422/485
• Audio: Line-out/Mic-in
Power Requirement
• Power type: ATX/AT
• Power input Voltage: 9-36 VDC
• Minimum Power Input: 9VDC 16A - 36VDC 5A
This product is intended to be supplied by a UL certified
power supply or UL certified DC source rated 19Vdc,
7.89A minimum, TMA 50 °C minimum. If you need further
assistance, please contact Advantech.
Specications
Packing List
2 MIC-770 Startup Manual
Miscellaneous
•Power Switch
(Orange: System standby/Green: System Power boot)
•COM1 TX & RX LED; COM2 TX & RX LED; Storage Status
LED
Environment
• Operating Temperature:
TDP 35W CPU: -10~50°C
TDP 65W CPU: -10~40°C (not supported by i7)
Note: Safety Certification Test Temperature: safety max
50 °C with SSD (TDP 35W CPU)
• Storage Temperature: -40 ~ 85 °C (-40 ~ 185 °F)
• Relative Humidity: 95% @ 40° C (non-condensing)
Physical Characteristics
• Dimensions (WxHxD): 77 x 192 x 230 mm
• Weight: 2.8 kg (6.17 lbs)
Jumpers and Connectors
The board has a number of jumpers that allow you to con-
figure your system to suit your application. The table below
lists the function of each of the jumpers and connectors.
Connectors
Label Function
VGA1 VGA Connector
HDMI1 HDMI connector
COM 12 RS-232/422/485
COM 34 RS-232
USB C1 USB 3.0
USB C2 USB 3.0
USB C3 USB3.1 and USB3.0 (Q370) or
USB2.0 (H310)
LAN 1 Intel i219LM (Q370) or Intel i219V (H310)
LAN 2 Intel i210IT
Audio Audio Jack (Line-out, Mic-in)
LED 6 COM 1/2 TX; RX; Storage device status
DC 9-36V Power connector
1
2
3
1
2
3
AT Module ATX Module
PSON1: System AT/ATX Module Selection
Function Jumper Setting
1-2 AT module
2-3 ATX module (Default)
The computer is supplied with a battery-powered realtime
clock circuit. There is a danger of explosion if battery is
incorrectly replaced. Replace only with same or equivalent
type recommended by the manufacturer. Discard used
batteries according to manufacturer’s instructions.
This device complies with the requirements in Part 15 of
the FCC rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful interference;
2. This device must accept any interference received,
including interference that may cause undesired
operation.
Memory Installation
MIC-770 supports DDR4 SO-DIMM non-ECC type memory
modules. If you need a detailed memory support list,
please contact your distributor or sales representative to
order compatible memory modules.
Power
Line out
LAN1/LAN2
Chassis GND
VGA
9-36 VDC
LED
COM1
TX/RX
COM2
TX/RX
DATA COM1/2
USB3.1
USB3.0/2.0
/3.0
HDMI
Specications (Cont.)
Declaration of Conformity
System I/O Interface
Simple Maintenance Process
Battery
MIC-770 Startup Manual 3
1. Undo 4 screws and remove the bottom cover.
2. Undo 4 screws to remove the storage tray.
3. Undo 3 screws to remove memory thermal cover.
4. Affix thermal pad (P/N: 1990019498N000) on memory
and assemble memory.
Note : Thermal pad and memory thermal cover must
be fully mated and compacted.
Storage Installation
1. Undo 4 screws and remove the bottom cover
2. Undo 4 screws to remove storage tray.
3. Secure the 4 x screws (P/N:1930002235)
4. Assemble SATA cable/power cable and replace stor-
age tray; secure with 4x screws.
5. Replace the bottom cover.
Mini-PCIE Installation
MIC-770 supports one full size Mini-PCIE.
1. Undo 4 screws and remove the bottom cover.
2. Install the module in the Mini-PCIe socket and secure
with screws.
3. Replace bottom cover and secure with screws.
Internal USB 2.0 Installation
1. Undo 4 screws and remove the bottom cover.
2. Loosen the screw and adjust bracket size in accor-
dance with USB dongle size.
3. Install USB dongle in the first socket. Only first socket
has this function.
4. Secure with screw and replace bottom cover and
attach with screws.
3
3
4
CPU Installation
1. Undo 4 screws and remove the bottom cover.
2. Undo 4 screws to remove storage tray.
3. Undo 4 screws in the corner of chassis.
4. Undo 4 screws around CPU to release AL heatsink.
5. Remove AL heatsink and install CPU.
6. Smear thermal grease onto CPU.
7. Replace AL heatsink, storage tray and bottom cover.
Mounting Kit Installation
1. Take the mounting kit from accessory box.
2. Secure the 4x screws (P/N: 1930007259-01, M4x4L
F/S D=8.5 H=1.5 (2+) ST/H BZn-NK) and install system
on table.
Simple Maintenance Process (Cont.)
4 MIC-770 Startup Manual
1. Read these safety instructions carefully.
2. Keep this Startup Manual for later reference.
3. Disconnect this equipment from any AC outlet before cleaning. Use a damp cloth. Do not use liquid or spray detergents
for cleaning.
4. For plug-in equipment, the power outlet socket must be located near the equipment and must be easily accessible.
5. Keep this equipment away from humidity.
6. Put this equipment on a reliable surface during installation. Dropping it or letting it fall may cause damage.
7. The openings on the enclosure are for air convection. Protect the equipment from overheating. DO NOT COVER THE
OPENINGS.
8. Make sure the voltage of the power source is correct before connecting the equipment to the power outlet.
9. Position the power cord so that people cannot step on it. Do not place anything over the power cord.
10. All cautions and warnings on the equipment should be noted.
11. If the equipment is not used for a long time, disconnect it from the power source to avoid damage by transient overvolt-
age.
12. Never pour any liquid into an opening. This may cause fire or electrical shock.
13. Never open the equipment. For safety reasons, the equipment should be opened only by qualified service personnel.
14. If one of the following situations arises, get the equipment checked by service personnel:
•The power cord or plug is damaged.
•Liquid has penetrated into the equipment.
•The equipment has been exposed to moisture.
•The equipment does not work well, or you cannot get it to work according to the user’s manual.
•The equipment has been dropped and damaged.
•The equipment has obvious signs of breakage.
15. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE STORAGE TEMPERATURE MAY GO BELOW
-40° C (-40° F) OR ABOVE 85° C (185° F). THIS COULD DAMAGE THE EQUIPMENT. THE EQUIPMENT SHOULD BE IN
A CONTROLLED ENVIRONMENT.
16. CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED. REPLACE ONLY WITH THE SAME OR
EQUIVALENT TYPE RECOMMENDED BY THE MANUFACTURER, DISCARD USED BATTERIES ACCORDING TO THE
MANUFACTURER’S INSTRUCTIONS.
17. The sound pressure level at the operator’s position according to IEC 704-1:1982 is no more than 70 dB (A).
18. RESTRICTED ACCESS AREA: The equipment should only be installed in a Restricted Access Area.
DISCLAIMER: This set of instructions is given according to IEC 704-1. Advantech disclaims all responsibility for the accuracy
of any statements contained herein.
Safety Instructions
MIC-770 Startup Manual 5
IO Connectors
System Dimensions
Internal USB 2 0 DDR4 socket
US M
MiniPCIe support mSATA
MiniPCIe support USIM
COM5/6
COM3/4
GPIO
eFuse
LPC
HDMI/DVI Con
ATX/AT jumper
Clear CMOS
Remote
USB switch
Autres manuels pour MIC-770
2
Table des matières
Autres manuels Advantech Ordinateur de bureau
Advantech
Advantech POC-W181 Manuel d'instructions
Advantech
Advantech ARK-2230 Manuel utilisateur
Advantech
Advantech UNO-2362G Series Manuel utilisateur
Advantech
Advantech MIC-770 Manuel utilisateur
Advantech
Advantech ARK-2250L-U6A1E Manuel utilisateur
Advantech
Advantech UNO-1110 Manuel utilisateur
Advantech
Advantech ARK-1220 Manuel utilisateur
Advantech
Advantech MIT-W102 Series Manuel d'installation et d'exploitation
Advantech
Advantech PPC-4150W Manuel utilisateur
Advantech
Advantech USC-360 Manuel utilisateur
Advantech
Advantech TREK-734 Manuel utilisateur
Advantech
Advantech ARS-2110TX Manuel utilisateur
Advantech
Advantech UNO-2174A Manuel utilisateur
Advantech
Advantech MIOS-5250 Manuel d'installation et d'exploitation
Advantech
Advantech AWS-8430T Manuel utilisateur
Advantech
Advantech USM-260 Manuel utilisateur
Advantech
Advantech TPC-307W Manuel utilisateur
Advantech
Advantech EPC-U2117 Manuel utilisateur
Advantech
Advantech MIO-6300 Manuel utilisateur
Advantech
Advantech SKY-642 4U Manuel d'installation et d'exploitation
