ADTRAN SR700ac Manuel utilisateur

SR700ac

Quick Start Guide

Installation

1. Connect one end of the phone cable to the DSL port on the gateway and connect the other end to the phone jack

on the wall installed by your provider.

2. Connect one end of the Ethernet cable to a LAN port on the gateway and connect the other end to your computer.

3. Plug the power adapter to the wall outlet and then connect the other end of it to the Power port of the gateway.

Turn on the unit by pressing the On/Off button on the back of the gateway.

4. If you plan to create an LTE connection, insert a SIM card into the SIM slot located under the WAN port.

Your gateway is now automatically being set up to connect to the Internet. This process may take a few minutes to

complete before you can begin using your Internet applications (browser, email, etc.). If you are unable to connect to the

Internet, verify that all cable connections are in place and the gateway’s power is turned on.

POWERWANDSL 1 2 3 4

Reset

SIM

123

LED Indicators

The LEDs on the SR700ac gateway can help you better understand

the current state of your gateway.

Legend: Green Green blinking Red Red blinking

LED Action Explanation

All LEDs except those

listed below

Connection enabled.

Data being transferred.

DSL & WAN Not lit Connection dropped; attempting resynchronization.

POWER Device has power and is ready to use.

Power up test failure.

Note: This LED flashes red briefly on startup; this is normal.

INET Gateway online.

Data being transferred.

Connection dropped; attempting resynchronization.

Not lit IP connection failed.

LED Action Explanation

WPS WPS setup procedure in progress.

WPS connection completed.

No partner found for pairing.

Session overlap detected. Possible security risk.

Warning: Do not press the Reset button unless you want to clear the current settings. The Reset button is in a small

circular hole on the rear panel. If you want to restore the default settings, insert a thin wire (such as a paper clip) into the

hole, press the Reset button gently for 1 second, and then release the button. The system reboots and returns to the

factory defaults.

Logging in to your gateway

To change the settings on your gateway, you must log in to the gateway's interface. Make sure that you have completed the

steps in "Installation" before you begin.

1. Open your internet browser application and type 192.168.1.1 into the address line. The login dialog appears.

2. Enter the factory default credentials shown below and click OK.

User Name: admin Password: admin

Note: Your service provider may use other settings. Contact your provider for details.

3. At the bottom of the page, click Manage gateway (advanced). The gateway interface appears.

Configuring the WAN manually

If the automatic connect process is unsuccessful, refer to the Advanced Setup >Layer2 Interface and WAN Service

sections of the SmartRG SR700ac Gateway User Manual to manually establish a connection.

Configuring an LTE Connection

1. With the gold contacts facing up, insert the SIM card containing the LTE information into the SIMslot on the back of

the gateway.

Note: The SR700ac gateway accepts a Standard SIM (15 x 25mm) card.

2. In the left navigation bar, click LTE WAN Service >Network Settings.

3. In the Network Dial Mode field, select the dial mode for this connection.

4. In the APN Name field, enter the APN for your network provider.

5. Click Save/Apply to apply your changes.

Note: It may take up to 90 seconds for the Save action to complete.

Your device should now be connected to your network via LTE.

WiFi Setup

Two methods, WPS and Manual, are available for WiFi setup. Perform the steps on this page first, and then follow the

instructions for the applicable method.

1. In the left navigation bar, click Wireless.

2. If the Enable Wireless option is not already selected, select it now.

3. Continue with your preferred method of wireless setup.

WPS Method

If the device you wish to connect to the Internet via your gateway supports the WPS secure WiFi connection method, follow

these steps.

1. In the left navigation bar, click Wireless.

2. Click the wireless band that you want to configure and then click Security.

3. In the Enable WPS field, select Enabled.

Autres manuels pour SR700ac

Table des matières

Autres manuels ADTRAN Routeur réseau

ADTRAN

ADTRAN NetVanta 3200 series Guide de l'utilisateur

ADTRAN

ADTRAN Express L128T S Manuel utilisateur

ADTRAN

ADTRAN ATLAS 550 Manuel utilisateur

ADTRAN

ADTRAN NetVanta 5305 Manuel utilisateur

ADTRAN

ADTRAN NetVanta 1535P Manuel

ADTRAN

ADTRAN NetVanta 4660 Manuel utilisateur

ADTRAN

ADTRAN NetVanta 3205 Manuel utilisateur

ADTRAN

ADTRAN Express 4200 Manuel utilisateur

ADTRAN

ADTRAN NetVanta 340 Manuel utilisateur

ADTRAN

ADTRAN 617600028F1 Manuel utilisateur

ADTRAN

ADTRAN Express XL 1200070L1 Manuel utilisateur

ADTRAN

ADTRAN 424RG Manuel utilisateur

ADTRAN

ADTRAN NetVanta 3200 series Manuel

ADTRAN

ADTRAN NetVanta 3458-PoE Manuel utilisateur

ADTRAN

ADTRAN NetVanta 3305 Manuel utilisateur

ADTRAN

ADTRAN NetVanta 7100 Manuel de service

ADTRAN

ADTRAN MX410 Guide de l'utilisateur

ADTRAN

ADTRAN Express 4100 Manuel utilisateur

ADTRAN

ADTRAN netvanta 1230 series Manuel

ADTRAN

ADTRAN NetVanta 3130 Manuel utilisateur

ADTRAN

ADTRAN NETVANTA 3100 Series Manuel utilisateur

ADTRAN

ADTRAN TSU NetVanta Manuel utilisateur

ADTRAN

ADTRAN Vanta 1335 Manuel

ADTRAN

ADTRAN Express L1.5 Manuel utilisateur

Manuels Routeur réseau populaires d'autres marques

Allnet

Allnet ALL0333AU Manuel utilisateur

HomeSeer

HomeSeer HT-SEL Manuel utilisateur

Sercomm

Sercomm Genesis OC3505D Manuel utilisateur

Billion

Billion BIPAC 5102 Series Manuel utilisateur

TP-Link

TP-Link TD-8817 Manuel utilisateur

Motorola

Motorola MR1900 Manuel utilisateur

Digi

Digi IX14 Manuel utilisateur

Cisco

Cisco NCS 540 Manuel

XAVi

XAVi X8821e Manuel utilisateur

BEC

BEC 6200WZL Manuel utilisateur

MikroTik

MikroTik hAP ac3 Series Manuel utilisateur

Korenix

Korenix JetNet 5428G Series Manuel utilisateur

NETGEAR

NETGEAR FS526T - Switch Manuel utilisateur

Korenix

Korenix JetNet 5710G Series Manuel utilisateur

Automated Logic

Automated Logic ZN551 Manuel du propriétaire

Cisco

Cisco ASR 1000 Series Manuel de l'opérateur

EnGenius

EnGenius ESR-9710 Manuel utilisateur

Cisco

Cisco 805 Series Instructions d'utilisation et de sécurité