ADTRAN ATLAS 550 Manuel utilisateur

ATLAS 550 (DC SYSTEM) P/N 1200550L1

For more detailed documentation, visit us online at www.adtran.com

Quick Start Guide

Connecting to the ATLAS 550

Connecting a VT100 terminal (or VT100 terminal emulator) to the CRAFT

interface (on the front panel of the unit) or the CONTROL INinterface (on the rear

panel of the unit) allows access to the terminal menus and management

features of the ATLAS 550.

Perform Steps Below in the Order Listed:

1. Configure a VT100 terminal (or terminal emulation software) with the

following settings:

If the terminal has a parallel setting, disable it and use serial.

2. Connect one end of the 6” data cable (supplied) into the ATLAS 550 CRAFT

or CONTROL INport. (This connection is RJ-45.) Make the connection to the

VT100 terminal as appropriate for your connection. ADTRAN supplies an

RJ-45 to DB-9 adapter for connections to standard DB-9 Communications

(COM) ports.

3. Initiate a terminal session and the LOGIN screen displays. The default

password is password. (Passwords in the ATLAS 550 are case sensitive.)

Data Rate: 9600 baud Stop Bits: 1

Data Bits: 8 Flow Control: None

Parity Bits: None

TEST

ERROR

ALARM

TEST

ERROR

ALARM

STATUS

ONLINE

TEST

12 3 4

NETWORK

MODULES

POWER

ACO

CRAFT

ETHERNET

REMOTE

SYSTEM

ATLAS 550

Network Module LEDs Option Module LEDs

Craft Interface

ACO Switch

Controller LEDs

Craft Pinout

System Status LEDs

The System Status LEDs display the status of the power supply, controller, and

other system parameters for the ATLAS 550. For a more detailed discussion of

the front panel LEDs, refer to Section 2, Engineering Guidelines, of the ATLAS

550 System Manual.

PIN NAME DESCRIPTION

1 GND Ground - connected to unit chassis

2 RTS Request to send - flow control

3 RXDATA Data received by the ATLAS 550

4 DTR Data terminal ready

5 TXDATA Data transmitted by the ATLAS 550

6 CD Carrier detect

7 UNUSED —

8 CTS Clear to send - flow control

LED Description

Power Indicates the status of the power supply

System Indicates the status of the unit controller and other system parameters.

Ethernet Indicates the status of the ethernet port.

Remote Indicates whether a user (Telnet or VT100) is logged in to the unit.

Reviewing the Front Panel

ATLAS 550 (DC SYSTEM) P/N 1200550L1

For more detailed documentation, visit us online at www.adtran.com

Quick Start Guide

ALL EMPTY SLOTS MUST BE

COVERED WITH BLANK PANELS

500 Series

CAUTION: FOR CONTINUED PROTECTION

AGAINST RISK OF FIRE, REPLACE ONLY

WITH SAME TYPE AND RATING OF FUSE.

ETHERNET CONTROL RELAY ALARM

MON

OUTIN

COMNONC GND

500 Series

NETWORK 2

NETWORK 1

500 Series

+Ð

USE COPPER CONDUCTORS ONLY

INPUT:

24Ð48V ,4A FUSE:

5A/48VDC

Network Module Slots Alarm Relay Connection

Control In/Out

10/100BaseT Ethernet

Option Module Slots DC Power Connection

Control In

10/100BaseT Ethernet Pinout

PIN NAME DESCRIPTION

1 GND Ground - connected to unit chassis

2 RTS Request to send - flow control

3 RXDATA Data received by the ATLAS 550

4 DTR Data terminal ready

5 TXDATA Data transmitted by the ATLAS 550

6 CD Carrier detect

7 UNUSED —

8 CTS Clear to send - flow control

PIN NAME DESCRIPTION

1 TX1 Transmit Positive

2 TX2 Transmit Negative

3 RX1 Receive Positive

4,5, 7, 8 — Unused

6 RX2 Receive Negative

Alarm Relay Connection Pinout

PIN NAME DESCRIPTION

1 Normally Closed (NC) Opens when a selected alarm condition is present.

2 Normally Open (NO) Closes when a selected alarm condition is present.

3 Common (COM) Common connection between external circuitry

and NC or NO terminal.

4 Chassis Ground (GND)

Connecting Power to the ATLAS 550

The DC powered ATLAS 550 comes equipped with a DC power supply to furnish

voltages for proper backplane operation. Please refer to Section 3, Network

Turnup Procedures, of the ATLAS 550 System Manual for more detailed

instructions.

• Power to the ATLAS 550 DC System must be from a reliably

grounded +24 or -48 VDC source which is electrically isolated

from the DC source.

• This unit shall be installed in accordance with Article 400 and

364.8 of the NEC NFPA 70.

• The branch circuit overcurrent protection shall be a fuse or

circuit breaker rated minimum 60 VDC, maximum 10A.

• A readily accessible disconnect device, that is suitably

approved and rated, shall be incorporated in the field wiring.

• Maximum recommended ambient operating temperature is

45°C

Reviewing the Rear Panel Design

DC Power Supply Connection

PIN NAME +24 VDC Source -48 VDC Source

1 + +24 VDC Ground (GND)

2 - Ground (GND) -48VDC

Autres manuels pour ATLAS 550

Ce manuel convient aux modèles suivants

Autres manuels ADTRAN Routeur réseau

ADTRAN

ADTRAN 1200422L1 Manuel

ADTRAN

ADTRAN NetVanta 3100 Series Manuel utilisateur

ADTRAN

ADTRAN Express L128FP Manuel utilisateur

ADTRAN

ADTRAN NetVanta 340 Manuel utilisateur

ADTRAN

ADTRAN TSU NetVanta Manuel utilisateur

ADTRAN

ADTRAN 1203870G1 Manuel utilisateur

ADTRAN

ADTRAN NetVanta 1535P Manuel

ADTRAN

ADTRAN Express 4200 Manuel utilisateur

ADTRAN

ADTRAN NetVanta 3000 Series Manuel

ADTRAN

ADTRAN NetVanta 5305 Manuel utilisateur

ADTRAN

ADTRAN NetVanta 1544F Manuel utilisateur

ADTRAN

ADTRAN Total Access 5000 Guide de référence rapide

ADTRAN

ADTRAN NetVanta 1335 Series Manuel utilisateur

ADTRAN

ADTRAN NetVanta 3000 Series Guide de l'utilisateur

ADTRAN

ADTRAN 617600028F1 Manuel utilisateur

ADTRAN

ADTRAN NetVanta 7100 Manuel de service

ADTRAN

ADTRAN NetVanta 5305 Manuel

ADTRAN

ADTRAN NetVanta 3430 Manuel utilisateur

ADTRAN

ADTRAN Express L768 Manuel utilisateur

ADTRAN

ADTRAN NETVANTA 3100 Series Manuel utilisateur

ADTRAN

ADTRAN Total Access 1250 Manuel utilisateur

ADTRAN

ADTRAN NetVanta 3000 Series Manuel

ADTRAN

ADTRAN NetVanta 3430 Manuel utilisateur

ADTRAN

ADTRAN Total Access 1248 Mode d’emploi

Manuels Routeur réseau populaires d'autres marques

Allnet

Allnet ALL0333AU Manuel utilisateur

HomeSeer

HomeSeer HT-SEL Manuel utilisateur

Sercomm

Sercomm Genesis OC3505D Manuel utilisateur

Billion

Billion BIPAC 5102 Series Manuel utilisateur

TP-Link

TP-Link TD-8817 Manuel utilisateur

Motorola

Motorola MR1900 Manuel utilisateur

Digi

Digi IX14 Manuel utilisateur

Cisco

Cisco NCS 540 Manuel

XAVi

XAVi X8821e Manuel utilisateur

BEC

BEC 6200WZL Manuel utilisateur

MikroTik

MikroTik hAP ac3 Series Manuel utilisateur

Korenix

Korenix JetNet 5428G Series Manuel utilisateur

NETGEAR

NETGEAR FS526T - Switch Manuel utilisateur

Korenix

Korenix JetNet 5710G Series Manuel utilisateur

Automated Logic

Automated Logic ZN551 Manuel du propriétaire

Cisco

Cisco ASR 1000 Series Manuel de l'opérateur

EnGenius

EnGenius ESR-9710 Manuel utilisateur

Cisco

Cisco 805 Series Instructions d'utilisation et de sécurité