Adtec Systema SW35S Manuel utilisateur
SW35S
SW35SW
SW35SB
SW35B
Component Checklist
Wall Channel (x1)
! IMPORTANT - Install Systema Wall Channel as per installation instructions.
! Refer to Systema Monitor arm or Monitor Spring Arm Installation Instructions for maximum load advice.
! The manufacturer accepts no responsibility for incorrect installations.
! The Systema Wall Channel is compatible with Systema Monitor Arms: SA13, SA46, SA71 and with Systema Monitor
Spring Arm: SS.
IMPORTANT INFORMATION:
Step 1. Check Components
Check what you have received against the component checklist and hardware above.
Nylon Anchor (x3)
Top Cap Screws
(x2)
Top Cap (x1)
SYSTEMA
Installation Instructions
Systema | 358mm Wall Channel
Step 2. Position Wall plate - Ergonomic Guidelines
Many experts believe that the extended use of any computer screen has the potential to cause serious injury to your eyes,
neck and back. This can be largely avoided by correctly positioning your display.
Viewing angle: Ergonomists recommend that the optimal position
of your display should be slightly below eye level. When looking at
the display’s centre the user should have a downward visual angle of
approximately 10°-20°.
Height: As a guide, the height (h) of your display should approximately
be as follows:
- Tall Male (Max): 560mm (22”)
- Short Male (Min): 368mm (14.5”)
- Tall Female (Max): 520mm (20.5”)
- Short Female (Min) 356mm (14”)
Atdec recommends that the bottom of the wall channel is
positioned 10mm above the worksurface to facilitate use by
the largest range of people.
Distance: For visual comfort, a viewing distance (d) between 500mm
(20”) to 750mm (29.5”) is recommended.
10º -20º
The Systema Wall
Channel
provides vertical
adjustment of
300mm (11.9”)
Guidelines based on a
720mm (28.3”) high
worksurface
(h)
(d)
Systema Monitor Arm
SA46 Shown
Please refer to the
Systema range Technical
Specifications for
dimensional details
10mm (0.4”)
Tools Required:
• Power Drill
• 5.5mm (1/4”) Drill Bit
• 8mm (5/16”) Drill Bit
• Phillips Head Screwdriver
M6 x 50mm
Countersunk
Screw (x3)
Step 3. Install Wall Channel
Nylon
Anchors
8mm (5/16”)
holes
M6 x 50mm
Countersunk
Screw
Systema
Monitor Arm
or Monitor
Spring Arm
Top Cap
Top Cap
Screws
M6 x 50mm
Countersunk
Screw
Systema
Monitor Arm
or Monitor
Spring Arm
Top Cap
Screws
Top Cap
5.5mm (1/4”)
holes
Installation Complete
You are now ready to install your Systema Monitor Arms.
Please refer to the Installation Instructions Included with these products.
No portion of this document or any artwork contained herein should be reproduced in any way without the express written consent of Atdec Pty Ltd.
Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. Published 06.11.14 ©
Masonry Timber Stud
Ce manuel convient aux modèles suivants
3
Table des matières
Autres manuels Adtec Support et étagère
Manuels Support et étagère populaires d'autres marques
Salamander
Salamander Acadia AC/W/L400/WH Manuel utilisateur
Fohhn
Fohhn VAT-09 Guide de l'utilisateur
ricoo
ricoo FS0522 Manuel utilisateur
AMSOIL
AMSOIL BMK-22 Guide rapide
Kargo Master
Kargo Master 48220 Manuel utilisateur
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur
