ADJ MOD STQ Manuel utilisateur

User Instructions

MOD STQ

instructions herein are subject to change without notice. ADJ Products, LLC logo and identifying

product names and numbers herein are trademarks of ADJ Products, LLC. Copyright protection

claimed includes all forms and matters of copyrightable materials and information now allowed by

statutory or judicial law or hereinafter granted. Product names used in this document may be

trademarks or registered trademarks of their respective companies and are hereby acknowledged.

All non-ADJ Products, LLC brands and product names are trademarks or registered trademarks of

their respective companies.

ADJ Products, LLC and all aliated companies hereby disclaim any and all liabilities for property,

equipment, building, and electrical damages, injuries to any persons, and direct or indirect economic

loss associated with the use or reliance of any information contained within this document, and/or as

a result of the improper, unsafe, unsucient and negligent assembly, installation, rigging, and operation

of this product.

Europe Energy Saving Notice

Energy Saving Matters (EuP 2009/125/EC)

Saving electric energy is a key to help protecting the enviroment. Please turn o all electrical products when

they are not in use. To avoid power consumption in idle mode, disconnect all electrical equipment from power

when not in use. Thank you!

FCC STATEMENT

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

FCC RADIO FREQUENCY INTERFERENCE WARNINGS & INSTRUCTIONS

This product has been tested and found to comply with the limits as per Part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful interference in a residential installa

tion. This device uses and can radiate radio frequency energy and, if not installed and used in accordance

with the included instructions, may cause harmful interference to radio communications. However, there is

no guarantee that interference will not occur in a particular installation. If this device does cause harmful

interference to radio or television reception, which can be determined by turning the device off and on, the

user is encouraged to try to correct the interference by one or more of the following methods:

· Reorient or relocate the device.

· Increase the separation between the device and the receiver.

· Connect the device to an electrical outlet on a circuit different from which the radio receiver is

connected.

· Consult the dealer or an experienced radio/TV technician for help.

DOCUMENT VERSION

Due to additional product features and/or enhancements, an updated version of this document

may be available online.

Please check www.adj.com for the latest revision/update of this manual before beginning

installation and/or programming.

10/01/19 1 1.00 4/5//7/8/9/12/13/15 Initial Version

Date Document

Version

Software

Version > DMX Channel Mode Notes

ADJ Products, LLC - www.adj.com - MOD STQ User Manual Page 2

MOD STQ Table of Contents

Introduction

Features I Warranty Registration

Safety Guidelines

Overview

Installation

DMX Set Up

DMX Addressing

DMX Modes & Values

Color Macro Chart

System Menu

Master-Slave Set Up

UC IR & Airstream Remote Control

Dimmer Curve Chart

Dimensional Drawings I Frost Filter Install

Power Linking I Trouble Shooting I Cleaning

Limited Warranty (USA Only)

Technical Specications

ADJ Products, LLC - www.adj.com - MOD STQ User Manual Page 3

MOD STQ Introduction

Unpacking: Thank you for purchasing the MOD STQ by ADJ Products, LLC. Every MOD STQ has

been thoroughly tested and has been shipped in perfect operating condition. Carefully check the ship-

ping carton for damage that may have occurred during shipping. If the carton appears to be damaged,

carefully inspect your xture for any damage and be sure all accessories necessary to operate the unit

has arrived intact. In the case damage has been found or parts are missing, please contact our toll free

customer support number for further instructions. Do not return this unit to your dealer without rst

contacting customer support.

Introduction: The ADJ MOD STQ is a DMX intelligent, high powered LED par fixture. This xture can

be used in a stand alone set up or connected in a Master/Slave set up. To optimize the performance

of this product, please read these operating instructions carefully to familiarize yourself with the basic

operations of this unit. These instructions contain important safety information regarding the use and

maintenance of this unit. Please keep this manual with the unit, for future reference.

Customer Support: Contact ADJ Service for any product related service and support needs. Also visit

forums.adj.com with questions, comments or suggestions.

Parts: To purchase parts online visit:

http://parts.adj.com (US)

http://www.adjparts.eu (EU)

ADJ SERVICE USA - Monday - Friday 8:00am to 4:30pm PST

Voice: 800-322-6337 | Fax: 323-582-2941 | [email protected]

ADJ SERVICE EUROPE - Monday - Friday 08:30 to 17:00 CET

Voice: +31 45 546 85 60 | Fax: +31 45 546 85 96 | [email protected]

ADJ PRODUCTS LLC USA

6122 S. Eastern Ave. Los Angeles, CA. 90040

323-582-2650 | Fax 323-532-2941 | www.adj.com | info@adj.com

ADJ SUPPLY Europe B.V

Junostraat 2 6468 EW Kerkrade, The Netherlands

+31 (0)45 546 85 00 | Fax +31 45 546 85 99

www.adj.eu | [email protected]

ADJ PRODUCTS GROUP Mexico

AV Santa Ana 30 Parque Industrial Lerma, Lerma, Mexico 52000

+52 (728) 282-7070

Caution! There are no user serviceable parts inside this unit. Do not attempt any repairs yourself,

doing so will void your manufactures warranty. In the unlikely event your unit may require service

please contact ADJ Products, LLC.

PLEASE recycle the shipping carton when ever possible.

MOD STQ Features

• Multi-Colors

• Electronic Dimming 0-100%

• Built in Microphone

• DMX-512 protocol

• Locking 3-Pin & 5-Pin XLR Connections In/Out

• 8 DMX Channel Modes: 4 / 5 / 7 / 8 / 9 / 12 / 13 / 15

• ADJ UC IR compatible and Airstream IR compatible

• Multiple Unit Power Linking (See page 22)

INCLUED:

1 x Scissor Yoke

1 x Locking Power Cable

3 x Frost Filters (20/40/60 Degrees)

MOD STQ Warranty Registration

The MOD STQ carries a 2 year limited warranty. Please fill out the enclosed warranty card to validate

your purchase. All returned service items whether under warranty or not, must be freight pre-paid and

accompany a return authorization (R.A.) number. The R.A. number must be clearly written on the out-

side of the return package. A brief description of the problem as well as the R.A. number must also

be written down on a piece of paper included in the shipping carton. If the unit is under warranty, you

must provide a copy of your proof of purchase invoice. You may obtain a R.A. number by contacting

our customer support team on our customer support number. All packages returned to the service

department not displaying a R.A. number on the outside of the package will be returned to the ship-

per.

ADJ Products, LLC - www.adj.com - MOD STQ User Manual Page 4

ADJ Products, LLC - www.adj.com - MOD STQ User Manual Page 5

MOD STQ Safety Guidelines

• Do not attempt to operate this unit if the power cord has been frayed or broken. Do not attempt to

remove or break o the ground prong from the electrical cord. This prong is used to reduce the risk

of electrical shock and re in case of an internal short.

• Disconnect from main power before making any type of connection.

• Do not remove the cover under any conditions. There are no user serviceable parts inside.

• Never operate this unit when it’s cover is removed.

• Never plug this unit in to a dimmer pack

• Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 6”

(15cm) between this device and a wall.

• Do not attempt to operate this unit, if it becomes damaged.

• During long periods of non-use, disconnect the unit’s main power.

• Always mount this unit in safe and stable matter.

• Power-supply cords should be routed so that they are not likely to be walked on or pinched by

items placed upon or against them, paying particular attention to the point they exit from the unit.

• Cleaning -The fixture should be cleaned only as recommended by the manufacturer. See page 23

for cleaning details.

• Heat -The appliance should be situated away from heat sources such as radiators, heat registers,

stoves, or other appliances (including amplifiers) that produce heat.

• The fixture should be serviced by qualified service personnel when:

A. The power-supply cord or the plug has been damaged.

B. Objects have fallen, or liquid has been spilled into the fixture.

C. The fixture does not appear to operate normally or exhibits a marked change in performance.

D. The fixture has fallen and/or subjected to extreme handling.

ADJ Products, LLC - www.adj.com - MOD STQ User Manual Page 6

MOD STQ Overview

SET UP

MODE UP

DOWN

DMX IN

DMX OUTDMX OUTPOWER OUT

DMX INPOWER IN

MODE BUTTON

SET UP BUTTON

UP BUTTON

DOWN BUTTON

LCD DISPLAY

LOCKING POWER

CONNECTOR IN

LOCKING POWER

CONNECTOR OUT

LOCKING 3-PIN & 5-PIN

XLR CONNECTORS IN

LOCKING 3-PIN & 5-PIN

XLR CONNECTORS OUT

ADJ Products, LLC - www.adj.com - MOD STQ User Manual Page 7

MOD STQ Installation

Screw one clamp via a M12 screw and nut into the bracket. Pull a safety cable through the opening(s)

located on either side of the bracket and over the trussing system or a safe xation spot. Insert the

end in the carabine and tighten the safety screw.

The MOD STQ is fully operational in three dierent mounting positions, hanging upside-down from a

ceiling or trussing, sideways on trussing, or set on a at level surface. Be sure this xture is kept at

least 12m (40ft) away from any ammable materials (decoration etc.). Always use and install the supplied

safety cable as a safety measure to prevent accidental damage and/or injury in the event the clamp

fails (see next page). Never use the carrying handles for secondary attachment.

When installing the unit, the trussing or area of installation must be able to hold 10 times the weight

without any deformation. When installing the unit must be secured with a secondary safety attachment,

e.g. and appropriate safety cable. Never stand directly below the unit when mounting, removing, or

servicing the unit.

Overhead mounting requires extensive experience, including calculating working load limits, installation

material being used, and perodic safety inspection of all installation material and unit. If you lack

these qualications, do not attempt the installation yourself.

These installaiton should be checked by a skilled person once a year.

NOTICE: The suitable enviromental temperature for this lighting xture is between -25˚ C to 45˚C.

Do not place this lighting xture in an enviroment where the temperatures are under or above the

temperatures stated above. This will allow the xture to run at its best and help prolong the xture

life.

CLAMP

(NOT INCLUDED)

ADJ Products, LLC - www.adj.com - MOD STQ User Manual Page 8

MOD STQ DMX Set Up

DMX-512: DMX is short for Digital Multiplex. This is a universal protocol used as a form of commu-

nication between intelligent fixtures and controllers. A DMX controller sends DMX data instructions

from the controller to the fixture. DMX data is sent as serial data that travels from fixture to fixture

via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX fixtures (most controllers only

have a DATA “OUT” terminal).

DMX Linking: DMX is a language allowing all makes and models of dierent manufactures to be

linked together and operate from a single controller, as long as all xtures and the controller are DMX

compliant. To ensure proper DMX data transmission, when using several DMX fixtures try to use

the shortest cable path possible. The order in which fixtures are connected in a DMX line does not

influence the DMX addressing. For example; a fixture assigned a DMX address of 1 may be placed

anywhere in a DMX line, at the beginning, at the end, or anywhere in the middle. When a fixture is

assigned a DMX address of 1, the DMX controller knows to send DATA assigned to address 1 to that

unit, no matter where it is located in the DMX chain.

Data Cable (DMX Cable) Requirements (For DMX Operation): The MOD STQ

can be controlled via DMX-512 protocol. The DMX address is set on the rear panel

of the MOD STQ. Your unit and your DMX controller require a standard 3-pin XLR

connector for data input and data output (Figure 1). We recommend Accu-Cable

DMX cables. If you are making your own cables, be sure to use standard 110-120

Ohm shielded cable (This cable may be purchased at almost all pro lighting stores).

Your cables should be made with a male and female XLR connector on either end

of the cable. Also remember that DMX cable must be daisy chained and cannot be

split. Figure 1

Notice: Be sure to follow gures two and three when making your own cables. Do not use the ground

lug on the XLR connector. Do not connect the cable’s shield conductor to the ground lug or allow the

shield conductor to come in contact with the XLR’s outer casing. Grounding the shield could cause a

short circuit and erratic behavior.

DMX512 IN

3-PIN XLR

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

DMX512

DMX+,DMX-,COMMON

Termination reduces signal errors and

avoids signal transmission problems

and interference. It is always advisable

to connect a DMX terminal, (Resistance

120 Ohm 1/4 W) between PIN 2 (DMX-)

and PIN 3 (DMX +) of the last fixture.

DMX +

DMX -

COMMON

DMX512 OUT

3-PIN XLR

Figure 2

Figure 3

1 Ground 1 Ground

XLR Male Socket XLR Pin Conguration

3 Hot

2 Cold 2 Cold

3 Hot

XLR Female Socket

Pin 3 = Data True (positive)

Pin 2 = Data Compliment (negative)

Pin 1 = Ground

ADJ Products, LLC - www.adj.com - MOD STQ User Manual Page 9

Special Note: Line Termination.

When longer runs of cable are used, you may need to use a terminator

on the last unit to avoid erratic behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is con-

nected between pins 2 and 3 of a male XLR connector (DATA + and DATA -). This unit is inserted in the

female XLR connector of the last unit in your daisy chain to terminate the line. Using a cable terminator

(ADJ part number Z-DMX/T) will decrease the possibilities of erratic behavior.

MOD STQ DMX Set Up

DMX512 IN

3-PIN XLR

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

DMX512

DMX+,DMX-,COMMON

Termination reduces signal errors and

avoids signal transmission problems

and interference. It is always advisable

to connect a DMX terminal, (Resistance

120 Ohm 1/4 W) between PIN 2 (DMX-)

and PIN 3 (DMX +) of the last fixture.

DMX +

DMX -

COMMON

DMX512 OUT

3-PIN XLR

Figure 4

5-Pin XLR DMX Connectors.

Some manufactures use 5-pin DMX-512 data cables for DATA transmis-

sion in place of 3-pin. 5-pin DMX xtures may be implemented in a 3-pin DMX line. When inserting

standard 5-pin data cables in to a 3-pin line a cable adaptor must be used, these adaptors are readily

available at most electric stores. The chart below details a proper cable conversion.

Conductor 5-Pin XLR Male (In)3-Pin XLR Female (Out)

Pin 1

Do Not Use

Pin 3

Pin 2

Pin 1

Pin 3

Pin 2

Not Used

Data True (+ signal)

Data Compliment (- signal)

Ground/Shield

3-Pin XLR to 5-Pin XLR Conversion

Table des matières

Autres manuels ADJ Matériel de DJ

ADJ

ADJ penta pix Manuel utilisateur

ADJ

ADJ INNO ROLL HP Manuel utilisateur

ADJ

ADJ Startec RAYZER Manuel utilisateur

ADJ

ADJ ENCORE LP18IP Manuel utilisateur

ADJ

ADJ VIZI WASH Z19 Manuel utilisateur

ADJ

ADJ VIZ870 Manuel utilisateur

ADJ

ADJ PAR Z100 5K Manuel utilisateur

ADJ

ADJ ELEMENT H6 PAK Manuel utilisateur

ADJ

ADJ UB 12H Manuel utilisateur

ADJ

ADJ 1226100361 Manuel utilisateur

ADJ

ADJ EVS3 Manuel utilisateur

ADJ

ADJ Color Stand LED Manuel utilisateur

ADJ

ADJ VIZI CMY 16RX Manuel utilisateur

ADJ

ADJ Mega GO Par64 PLUS Manuel utilisateur

ADJ

ADJ MOD TW100 Manuel utilisateur

ADJ

ADJ ADJ FLAT PAR TRI18X Manuel utilisateur

ADJ

ADJ FLAT PAR QWH5XS Manuel utilisateur

ADJ

ADJ MB DMX II Manuel utilisateur

ADJ

ADJ VF SNOW FLURRY HO Manuel utilisateur

ADJ

ADJ PAR Z120 RGBW Manuel utilisateur

ADJ

ADJ Mega GO Bar 50 RGBA Manuel utilisateur

ADJ

ADJ SABER SPOT WW Manuel utilisateur

ADJ

ADJ PAR Z120 RGBW Manuel utilisateur

ADJ

ADJ 3D Vision Manuel utilisateur

Manuels Matériel de DJ populaires d'autres marques

ALPHA LITE

ALPHA LITE ALPHA 1500 Manuel du propriétaire

Chauvet

Chauvet OVATION E-930VW Manuel utilisateur

Zumtobel

Zumtobel APHRODITE Home Manuel utilisateur

Snow Masters

Snow Masters Zig Oscillator Manuel utilisateur

EuroLite

EuroLite 50530554 Manuel utilisateur

Beamz

Beamz BUV243 Manuel utilisateur

thomann

thomann Stairville DJ Lase 40-G MK-III Manuel utilisateur

Eagletone

Eagletone 6 Eyes Flower Manuel utilisateur

EuroLite

EuroLite FLD-1508 Manuel utilisateur

Technical Pro

Technical Pro LG8xSEA Manuel utilisateur

JB Systems

JB Systems Lounge Laser DMX Manuel utilisateur

Lightmaxx

Lightmaxx Vega Halo 90 Manuel utilisateur

Elation

Elation FUZE WASH Z350 Manuel utilisateur

Maverick

Maverick MK3 WASH Manuel utilisateur

Infinity

Infinity TF-260C7 Fresnel Manuel utilisateur

Chauvet

Chauvet EVE E-50Z Manuel utilisateur

Eliminator Lighting

Eliminator Lighting E 138 Manuel utilisateur

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Manuel utilisateur