ADJ ELEMENT HEXIP Manuel utilisateur
User Instructions
ELEMENT HEXIP
Europe Energy Saving Notice
Energy Saving Matters (EuP 2009/125/EC)
Saving electric energy is a key to help protecting the enviroment. Please turn o all electrical products
when they are not in use. To avoid power consumption in idle mode, disconnect all electrical equipment
from power when not in use. Thank you!
©2019 ADJ Products, LLC all rights reserved. Information, specications, diagrams, images, and
instructions herein are subject to change without notice. ADJ Products, LLC logo and identifying
product names and numbers herein are trademarks of ADJ Products, LLC. Copyright protection
claimed includes all forms and matters of copyrightable materials and information now allowed by
statutory or judicial law or hereinafter granted. Product names used in this document may be
trademarks or registered trademarks of their respective companies and are hereby acknowledged.
All non-ADJ Products, LLC brands and product names are trademarks or registered trademarks of
their respective companies.
ADJ Products, LLC and all aliated companies hereby disclaim any and all liabilities for property,
equipment, building, and electrical damages, injuries to any persons, and direct or indirect economic
loss associated with the use or reliance of any information contained within this document, and/or as
a result of the improper, unsafe, unsucient and negligent assembly, installation, rigging, and operation
of this product.
FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
FCC RADIO FREQUENCY INTERFERENCE WARNINGS & INSTRUCTIONS
This product has been tested and found to comply with the limits as per Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in a residential installa-
tion. This device uses and can radiate radio frequency energy and, if not installed and used in accordance
with the included instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this device does cause harmful
interference to radio or television reception, which can be determined by turning the device off and on, the
user is encouraged to try to correct the interference by one or more of the following methods:
· Reorient or relocate the device.
· Increase the separation between the device and the receiver.
· Connect the device to an electrical outlet on a circuit different from which the radio receiver is
connected.
· Consult the dealer or an experienced radio/TV technician for help.
DOCUMENT VERSION
Due to additional product features and/or enhancements, an updated version of this document
may be available online.
Please check www.adj.com for the latest revision/update of this manual before beginning
installation and/or programming.
09/11/17 1.2 1.00 6/7/8/11/12 ETL Version
11/07/18 1.4 1.06 No Change Display Lock
IR Remote Functions Updated
03/21/19 Service Port Added
Date Document
Version
Software
Version > DMX Channel
Mode Notes
1.6 N/C No Change
ADJ Products, LLC - www.adj.com - Element HEXIP User Manual Page 2
Element HEXIP Table of Contents
Introduction
Features I Warranty Registration I Installation
Safety Precautions
Battery Precautions I Battery Status & Charging
IP Notice
Overview
DMX Addressing
DMX Control
DMX Modes
Color Macro Chart
System Menu
Operating Instructions
WiFly Set Up I WiFly Master-Slave Set Up
UC IR & Airstream Control
Dimmer Curve Chart
Dimensional Drawings
Fuse Replacement I Trouble Shooting I Cleaning
Warranty
Technical Specications
3
4
5
7
9
10
11
12
13
15
16
17
21
22
23
24
25
26
27
ADJ Products, LLC - www.adj.com - Element HEXIP User Manual Page 3
Element HEXIP Introduction
Unpacking: Thank you for purchasing the Element HEXIP by ADJ Products, LLC. Every Element
HEXIP has been thoroughly tested and has been shipped in perfect operating condition. Carefully
check the shipping carton for damage that may have occurred during shipping. If the carton appears
to be damaged, carefully inspect your xture for any damage and be sure all accessories necessary
to operate the unit has arrived intact. In the case damage has been found or parts are missing, please
contact our toll free customer support number for further instructions. Do not return this unit to your
dealer without rst contacting customer support.
Introduction: The Element HEXIP is a IP rated, rechargeable lithium battery powered, DMX intelligent,
LED par fixture with ADJ’s WiFly TransCeiver with wireless DMX built-in. This unit gives you the freedom to
set up your fixture where ever you wish without the restrictions of power or DMX cabling. This xture
can be used in a stand alone mode or connected in a Master/Slave conguration. This unit has five oper-
ating modes: Auto mode (color change, color fade, color change and fade combination), RGBWA+UV
Dimmer mode, Static Color mode, and DMX control mode. To optimize the performance of this product,
please read these operating instructions carefully to familiarize yourself with the basic operations of
this unit. These instructions contain important safety information regarding the use and maintenance
of this unit. Please keep this manual with the unit, for future reference.
Customer Support: Contact ADJ Service for any product related service and support needs. Also visit
forums.adj.com with questions, comments or suggestions.
Parts: To purchase parts online visit http://parts.americandj.com
ADJ SERVICE USA - Monday - Friday 8:00am to 4:30pm PST
ADJ SERVICE EUROPE - Monday - Friday 08:30 to 17:00 CET
ADJ PRODUCTS LLC USA
6122 S. Eastern Ave. Los Angeles, CA. 90040
323-582-2650 | Fax 323-532-2941 | www.adj.com | info@adj.com
ADJ SUPPLY Europe B.V
Junostraat 2 6468 EW Kerkrade, The Netherlands
+31 (0)45 546 85 00 | Fax +31 45 546 85 99
ADJ PRODUCTS GROUP Mexico
AV Santa Ana 30 Parque Industrial Lerma, Lerma, Mexico 52000
+52 (728) 282-7070
Warning! To prevent or reduce the risk of electrical shock or re, do not expose this unit to rain or
moisture.
Caution! There are no user serviceable parts inside this unit. Do not attempt any repairs yourself,
doing so will void your manufactures warranty. In the unlikely event your unit may require service
please contact ADJ Products, LLC.
PLEASE recycle the shipping carton when ever possible.
Element HEXIP Features
Element HEXIP Warranty Registration
Element HEXIP Installation
The Element HEXIP carries a 2 year limited warranty. Please fill out the enclosed warranty card to
validate your purchase. All returned service items whether under warranty or not, must be freight pre-
paid and accompany a return authorization (R.A.) number. The R.A. number must be clearly written on
the outside of the return package. A brief description of the problem as well as the R.A. number must
also be written down on a piece of paper included in the shipping carton. If the unit is under warranty,
you must provide a copy of your proof of purchase invoice. You may obtain a R.A. number by con-
tacting our customer support team on our customer support number. All packages returned to the
service department not displaying a R.A. number on the outside of the package will be returned to the
shipper.
The unit should be mounted using a mounting clamp (not provided), axing it to the mounting
bracket that is provided with the unit. Always ensure that the unit is rmly xed to avoid vibration
and slipping while operating. Always ensure that the structure to which you are attaching the unit is
secure and is able to support a weight of 10 times the unit’s weight. ALWAYS use safety cables that
can hold 12 times the weight of the unit when installing the xture.
This equipment must be installed by a professional, and it must be installed in a place where it is out
of the reach of people’s grasp.
ADJ Products, LLC - www.adj.com - Element HEXIP User Manual Page 4
• Five Operating Modes
• Electronic Dimming 0-100%
• RGBWA+UV Color Mixing
• 5 Selectable Dimming Curves
• 63 Color Macros
• Built in Microphone
• DMX-512 protocol
• 5 DMX Channel Modes: 6 Channel Mode, 7 Channel Mode, 8 Channel Mode, 11 Channel Mode, &
12 Channel Mode
• Rechargeable Lithium Battery
• Built-In ADJ’s WiFly TransCeiver Wireless DMX
• ADJ UC IR & Airstream IR compatible
Incuded Accessories:
1 x I.E.C. power cable
1 x UC IR Remote Control
1 x Airstream IR Transmitter
ADJ Products, LLC - www.adj.com - Element HEXIP User Manual Page 5
Element HEXIP Safety Precautions
NOT FOR RESIDENTIAL/HOUSE HOLD USE
NON DESTINÉ À UN USAGE DOMESTIQUE
SUITABLE FOR DAMP LOCATIONS
CONVIENT AUX EMPLACEMENTS HUMIDES
• To reduce the risk of electrical shock or re, do not expose this unit rain or moisture
• Do not attempt to operate this unit if the power cord has been frayed or broken. Do not attempt to
remove or break o the ground prong from the electrical cord. This prong is used to reduce the risk
of electrical shock and re in case of an internal short.
• Disconnect from main power before making any type of connection.
• Do not remove the cover under any conditions. There are no user serviceable parts inside.
• Never operate this unit when it’s housing is removed.
• Never plug this unit in to a dimmer pack
• Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 6” (15cm)
between this device and a wall.
• Do not attempt to operate this unit, if it becomes damaged.
• During long periods of non-use, disconnect the unit’s main power.
• Always mount this unit in safe and stable matter.
• Power supply cords should be routed so that they are not likely to be walked on or pinched by
items placed upon or against them, paying particular attention to the point they exit from the unit.
• Cleaning -The fixture should be cleaned only as recommended by the manufacturer. See page 25
for cleaning details.
• Heat -The appliance should be situated away from heat sources such as radiators, heat registers,
stoves, or other appliances (including amplifiers) that produce heat.
• The fixture should be serviced by qualified service personnel when:
A. The power-supply cord or the plug has been damaged.
B. The appliance does not appear to operate normally or exhibits a marked change in performance.
C. The fixture has fallen and/or subjected to extreme handling.
Element HEXIP Safety Precautions
RISK GROUP 3 - RISK OF EXPOSURE TO ULTRAVIOLET (UV) RADIATION!
FIXTURE EMITS HIGH INTENSITY ULTRAVIOLET (UV) LIGHT FROM THE UV LED.
WEAR PROPER EYE AND SKIN PROTECTION.
AVOID PROLONGED PERIODS OF EXPOSURE TO THE UV LED.
AVOID WEARING WHITE COLOR CLOTHING AND/OR USING (UV) PAINTS ON SKIN.
AVOID DIRECT EYE AND/OR SKIN EXPOSURE AT DISTANCES SHORTER THAN 11 feet (3.3m).
DO NOT OPERATE FIXTURE WITH DAMAGED OR MISSING EXTERNAL COVER.
DO NOT LOOK DIRECTLY INTO THE (UV) LIGHT AND/OR VIEW (UV) LIGHT DIRECTLY WITH
OPTICAL INSTRUMENTS THAT MAY CONCENTRATE THE LIGHT/RADIATION OUTPUT.
INDIVIDUALS SUFFERING FROM A RANGE OF EYE CONDITIONS, SUNLIGHT EXPOSURE
DISORDERS, OR INDIVIDUALS USING PHOTOSENSITIVE MEDICATION, MAY RECEIVE
DISCOMFORT IF EXPOSED TO THE ULTRAVIOLET (UV) LIGHT EMITTED FROM THIS FIXTURE.
ADJ Products, LLC - www.adj.com - Element HEXIP User Manual Page 6
ADJ Products, LLC - www.adj.com - Element HEXIP User Manual Page 7
Element HEXIP Battery Precautions
1. Handling of Batteries
1.1 Do Not Short Circuit the Battery
Try to never short circuit the battery. It generates a very high current which could cause the battery
to overheat which may result in electrolyte gel leakage, harmful fumes, or explosion. The LIR tabs
may easily short-circuit by placing them on conductive surface. A short circuit may lead to heat build
up and damage of the battery. An appropriate circuitry with PCM is employed to protect accidental
short circuit of the battery pack.
1.2 Mechanical shock
Droping the unit, impact hit, bending, etc. may cause failure or shortend life of the LIR battery.
3. Other
3.1 Battery connection
1). Direct soldering of wire leads or devices to the battery is strictly prohibited.
2). Lead tabs with pre-soldered wiring shall be spot welded to the batteries. Direct soldering may
cause damage of components, such as separator and insulator, by heat build up.
3.2 Prevention of short circuit within a battery pack
There is enough insulation layers between wiring and the batteries to provide extra safety protection.
The battery pack is constructed in a way that no short circuit will occur which may cause smoke or
re.
3.3 Do No Disassemble the Batteries
1). Never disassemble the batteries.
Doing this may cause a internal short circuit in the battery, which may lead to harmful fumes, re,
explosion, or other problems.
2). Electrolyte Gel is harmful
Electrolyte Gel should not leak from the LIR battery. Should the electrolyte gel come into contact
with the skin or eyes, ush the area of contact immediately with fresh water and seek medical atten-
tion immediately.
3.4 Do Not Expose the Battery to Heat or Fire
Never incinerate or dispose of the batteries in re. This may cause an explosion, which would be
very dangerous.
3.5 Do Not Expose the Battery to water or liquids
Never soak/drop the batteries in liquids such as water, seawater, drinks such as soft drinks, juices,
coee or other.
3.6 Battery Replacement
For battery replacement please contact ADJ customer support (800) 322-6337.
3.7 Do Not use a damaged Battery
The battery could be damaged during shipping, caused by shock. Should the battery be found dam-
aged, including damages to the plastic casing of the battery, deformation of the battery package,
smelling of an electrolyte, or leakage of the electrolyte gel, or other, DO NOT use the battery. A bat-
tery with a odor of electrolyte or a gel leakage should be placed away from re to avoid re or explo-
sion.
ADJ Products, LLC - www.adj.com - Element HEXIP User Manual Page 8
Element HEXIP Battery Precautions
4. Battery Storage
When storing the battery, it should be stored at room temperature, with a charge of at least 50%. We
recommend that during long periods of storage that the battery be charged every 6 months. Doing
this will prolong the life of the battery and will also make sure that the battery charge does not fall
below the 30% mark.
5. Other Chemical Reaction
Because batteries utilize a chemical reaction, battery performance will deteriorate over time even if
stored for a long period of time without being used. In addition, if the various usage conditions such
as charge, discharge, ambient temperature, etc. are not maintained within the specied ranges, the
life expectancy of the battery maybe shortened or the device in which the battery is used may be
damaged by electrolyte gel leakage. If the batteries cannot maintain a charge for long periods of
time, even when they are charged correctly, this may indicate it is time to change the battery.
6. Battery Disposal
Please dispose of battery according to local regulations.
Battery Status:
This function is used to check the life status of the battery.
Plug the fixture in and press the MODE button until “bXXX” is displayed. “XXX” represents the current
battery life. The number that is displayed is the remaining battery life. If “b---” is displayed, it means
that you are running the unit on AC power. Please do not let the battery fully die, this severly
shortens the life of the battery.
NOTE: When the battery life is below 30% the battery percentage will flash. At 15% power the fixture
will shut off.
NOTE: When using battery power, after 20 seconds of inactivity, the display will revert back to
the battery life display.
Battery Recharge: To recharge the battery, plug the supplied I.E.C. cord into the I.E.C. input on the
side of the unit and plug the other end into a matching power supply. It takes about 4 hours to reach
full charge (with the power o). The display will STOP ashing when the unit reaches 100% charge.
Note: When unplugging the unit from charging and then applying power via battery, there will
be a minimal charge drop.
For a faster recharge, turn the Load setting to “O” and turn the battery “On”. See “Load Setting” on
page 17.
Element HEXIP Battery Status & Charging
ADJ Products, LLC - www.adj.com - Element HEXIP User Manual Page 9
Element HEXIP IP Notice
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels ADJ Matériel de DJ
ADJ
ADJ FS3000LED Manuel utilisateur
ADJ
ADJ 1226100374 Manuel utilisateur
ADJ
ADJ MDF2PSUX117 Guide de l'utilisateur
ADJ
ADJ Fusion Tri FX Bar Manuel utilisateur
ADJ
ADJ 32 HEX PANEL IP Manuel utilisateur
ADJ
ADJ STARTEC BOOM BOX FX2 Manuel utilisateur
ADJ
ADJ ENCORE FR150Z Manuel utilisateur
ADJ
ADJ MOD QW100 Manuel utilisateur
ADJ
ADJ ENTOUR ICE Manuel utilisateur
ADJ
ADJ Encore Profile 1000 Color Manuel utilisateur
ADJ
ADJ ENCORE BURST RGBW IP Manuel utilisateur
ADJ
ADJ VIZI CMY300 Manuel utilisateur
ADJ
ADJ REVO 4 IR Manuel utilisateur
ADJ
ADJ VIZI CMY300 Manuel utilisateur
ADJ
ADJ 5PX HEX PEARL Manuel utilisateur
ADJ
ADJ Mega Go Bar 50 Manuel d'utilisation et d'entretien
ADJ
ADJ Vizi Beam Hybrid 2R Manuel utilisateur
ADJ
ADJ DOTZ PAR 100 Manuel utilisateur
ADJ
ADJ ELEMENT Series Manuel utilisateur
ADJ
ADJ Vizi BSW 300 Manuel utilisateur
Manuels Matériel de DJ populaires d'autres marques
thomann
thomann Stairville DJ Lase 40-G MK-III Manuel utilisateur
Eagletone
Eagletone 6 Eyes Flower Manuel utilisateur
EuroLite
EuroLite FLD-1508 Manuel utilisateur
Technical Pro
Technical Pro LG8xSEA Manuel utilisateur
JB Systems
JB Systems Lounge Laser DMX Manuel utilisateur
Lightmaxx
Lightmaxx Vega Halo 90 Manuel utilisateur
Elation
Elation FUZE WASH Z350 Manuel utilisateur
Maverick
Maverick MK3 WASH Manuel utilisateur
Infinity
Infinity TF-260C7 Fresnel Manuel utilisateur
Chauvet
Chauvet EVE E-50Z Manuel utilisateur
Eliminator Lighting
Eliminator Lighting E 138 Manuel utilisateur
EuroLite
EuroLite Mini Multicolor LED Flashing Light SC Manuel utilisateur