ADJ Dotz Par Manuel utilisateur

User Manual

DOTZ PARDOTZ PAR

Rev 04/2021

instructions herein are subject to change without notice. ADJ Products, LLC logo and identifying

product names and numbers herein are trademarks of ADJ Products, LLC. Copyright protection

claimed includes all forms and matters of copyrightable materials and information now allowed by

statutory or judicial law or hereinafter granted. Product names used in this document may be trade-

marks or registered trademarks of their respective companies and are hereby acknowledged. All

non-ADJ Products, LLC brands and product names are trademarks or registered trademarks of their

respective companies.

ADJ Products, LLC and all aliated companies hereby disclaim any and all liabilities for property,

equipment, building, and electrical damages, injuries to any persons, and direct or indirect economic

loss associated with the use or reliance of any information contained within this document, and/or as

a result of the improper, unsafe, insucient and negligent assembly, installation, rigging, and opera-

tion of this product.

Europe Energy Saving Notice

Energy Saving Matters (EuP 2009/125/EC)

Saving electric energy is a key to help protecting the enviroment. Please turn o all electrical products when

they are not in use. To avoid power consumption in idle mode, disconnect all electrical equipment from power

when not in use. Thank you!

ADJ Products, LLC - www.adj.com - Dotz Par User Manual Page 2

Dotz Par Introduction

ADJ Products, LLC - www.adj.com - Dotz Par User Manual Page 3

Unpacking: Thank you for purchasing the Dotz Par by ADJ Products, LLC. Every Dotz Par has been

thoroughly tested and has been shipped in perfect operating condition. Carefully check the shipping

carton for damage that may have occurred during shipping. If the carton appears to be damaged,

carefully inspect your xture for any damage and be sure all accessories necessary to operate the unit

have arrived intact. In the event that damage has been found or parts are missing, please contact our

toll free customer support number for further instructions. Do not return this unit to your dealer without

rst contacting customer support.

Introduction: The Dotz Par is part of ADJ’s continuing pursuit for creating high quality aordable

intelligent xtures. The Dotz Par is a high performance, DMX intelligent, moving head LED xture. This

xture is a great piece for retail stores, displays, mood, architectural, interior and exterior decoration,

and clubs. This unit can be used as a stand alone unit or in Primary/Secondary conguration. The unit

can also be controlled via DMX controller. This xture is suitable for theaters, studios, retail stores,

and other similar locations.

Customer Support: ADJ Products, LLC provides a customer support line, to provide set up help and

to answer any questions that may arise during initial set up or operation. You may also visit us on the

web at www.adj.com for any comments or suggestions. Service Hours are Monday through Friday

8:00 a.m. to 4:30 p.m. Pacic Standard Time.

Voice: (800) 322-6337

Fax: (323) 582-2941

E-mail: [email protected]

Warning! To prevent or reduce the risk of electrical shock or re, do not expose this unit to rain or

moisture.

Caution! There are no user serviceable parts inside this unit. Do not attempt any repairs yourself, as

doing so will void your manufacturer’s warranty. In the unlikely event that your unit may require service,

please contact ADJ Products, LLC.

PLEASE recycle the shipping carton whenever possible.

ADJ Products, LLC - www.adj.com - Dotz Par User Manual Page 4

Dotz Par Features

• RGB Color Mixing

• Strobing

• Electronic Dimming 0-100%

• Built in Microphone

• DMX-512 protocol

• Four DMX Modes: 3 Channel Mode, 4 Channel Mode, 5 Channel Mode, & 9 Channel Mode,

• 4 Operating Modes: Sound Active, Auto Run, Built-In Programs, or DMX Control

• Power Cord Daisy Chaining (see Power Cord Daisy Chain section of this manual)

Dotz Par Warranty Registration

The Dotz Par carries a 2 year (730 days) limited warranty. Please fill out the enclosed warranty card

to validate your purchase and warranty. You may also register your product online at www.adj.com.

All returned service items, whether under warranty or not, must be freight pre-paid and accompanied

by a return authorization (R.A.) number. If the unit is under warranty, you must provide a copy of your

proof of purchase invoice. Please contact ADJ Products, LLC customer support for an R.A. number.

Dotz Par General Instructions

To optimize the performance of this product, please read these operating instructions carefully to

familiarize yourself with the basic operations of this unit. These instructions contain important safety

information regarding the use and maintenance of this unit. Please keep this manual with the unit for

future reference.

ADJ Products, LLC - www.adj.com - Dotz Par User Manual Page 5

Dotz Par Safety Precautions

• To reduce the risk of electrical shock or fire, do not expose this unit to rain or moisture.

• Do not spill water or other liquids into or on to your unit.

• Be sure that the power outlet matches the required voltage for your unit.

• Do not attempt to operate this unit if the power cord is frayed or broken.

• Do not attempt to remove or break off the ground prong from the electrical cord. This prong is

used to reduce the risk of electrical shock and fire in case of an internal short.

• Disconnect from main power before making any type of connection.

• Do not remove the cover under any conditions. There are no user erviceable parts inside.

• Never operate this unit with the cover removed.

• Never plug this unit in to a dimmer pack.

• Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 6”

(15cm) between this device and a wall.

• Do not attempt to operate this unit if it has been damaged in any way.

• This unit is intended for indoor use only. Use of this product outdoors voids all warranties.

• During long periods of non-use, disconnect the unit’s main power.

• Always mount this unit in a safe and stable matter.

• Power-supply cords should be routed so that they are not likely to be walked on or pinched by

items placed upon or against them, paying particular attention to the point at which they exit

from the unit.

• Cleaning - The fixture should be cleaned only as recommended by the manufacturer. See the

Cleaning section of this manual for cleaning details.

• Heat - The appliance should be situated away from heat sources such as radiators, heat regis-

ters, stoves, or other appliances (including amplifiers) that produce heat.

• The fixture should be serviced by qualified service personnel when:

A. The power-supply cord or the plug has been damaged.

B. Objects have fallen onto, or liquid has been spilled into, the appliance.

C. The appliance has been exposed to rain or water.

D. The appliance does not appear to operate normally or exhibits a marked change in perfor-

mance.

Dotz Par Set Up

Power Supply: The ADJ Dotz Par contains an automatic voltage switch, which will automatically

sense the voltage when it is plugged into the power source. With this switch, there is no need to

worry about the correct power voltage, and this unit can be plugged in anywhere.

DMX-512: DMX is short for Digital Multiplex. This is a universal protocol that is used as a form

of communication between intelligent fixtures and controllers. A DMX controller sends DMX data

instructions from the controller to the fixture. DMX data is sent as serial data that travels from fixture

to fixture via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX fixtures (most control-

lers only have a DATA “OUT” terminal).

DMX Linking: DMX is a language allowing all makes and models of different manufacturers to be

linked together and operate from a single controller, as long as all fixtures and the controller are DMX

compliant. To ensure proper DMX data transmission, try to use the shortest cable path possible

when linking several DMX fixtures. The order in which fixtures are connected in a DMX line does not

influence the DMX addressing. For example, a fixture assigned a DMX address of 1 may be placed

anywhere in a DMX line: at the beginning, at the end, or anywhere in the middle. When a fixture is

assigned a DMX address of 1, the DMX controller knows to send DATA assigned to address 1 to that

unit, no matter where it is located in the DMX chain.

Data Cable (DMX Cable) Requirements (For DMX and Primary/Secondary Operation): The Dotz

Par can be controlled via DMX-512 protocol. The device features 4 DMX Channel Modes; please see

the Channel Mode sections of this manual for the different modes. The DMX address can be con-

figured using the control panel on the rear of the unit. Your unit and your DMX controller require an

approved DMX-512 110 Ohm Data cable for data input and data output (Figure 1). We recommend

Accu-Cable DMX cables. If you are making your own cables, be sure to use standard 110-120 Ohm

shielded cable (This cable may be purchased at almost all professional sound and lighting stores).

Your cables should be made with a male XLR connector on one end of the cable and a female XLR

connector at the other. Also remember that DMX cable must be daisy chained and cannot be split.

ADJ Products, LLC - www.adj.com - Dotz Par User Manual Page 6

ADJ Products, LLC - www.adj.com - Dotz Par User Manual Page 7

Notice: Be sure to follow figures two and three when making your own cables. Do not use the ground

lug on the XLR connector. Do not connect the cable’s shield conductor to the ground lug or allow the

shield conductor to come into contact with the XLR cable’s outer casing. Grounding the shield could

cause a short circuit and result in erratic behavior.

Special Note: Line Termination. When longer runs of cable are used, you may need to use a ter-

minator on the last unit to avoid erratic behavior. A terminator is a 110-120 ohm 1/4 watt resistor

which is connected between pins 2 and 3 of a male XLR connector (DATA + and DATA -). This unit is

inserted in the female XLR connector of the last unit in your daisy chain to terminate the line. Using a

cable terminator (ADJ part number Z-DMX/T) will decrease the chances of erratic behavior.

5-Pin XLR DMX Connectors. Some manufacturers use 5-pin DMX-512 data cables for DATA trans-

mission in place of 3-pin. 5-pin DMX fixtures may be implemented in a 3-pin DMX line. When insert-

ing standard 5-pin data cables into a 3-pin line, a cable adaptor must be used. These adaptors are

readily available at most electronics stores. The chart below details a proper cable conversion.

Dotz Par Set Up

Dotz Par System Menu

ADJ Products, LLC - www.adj.com - Dotz Par User Manual Page 8

The LCD backlight will shut off after 30 seconds. To illuminate the background again, press

the MODE button for 5 seconds.

DMX Mode - Set the DMX Address and DMX Channel Mode.

1. Press the MODE button until “AXXX” is displayed. “XXX” represents the currently used address.

2. Use the UP or DOWN buttons to change the DMX address.

3. After setting your DMX address, press ENTER. You can now select your desired DMX channel

mode. Use the UP or DOWN buttons to find your desired DMX channel mode, then press ENTER

to confirm your selection.

4. Next, select your dimmer curve setting. There are 5 available options. Select you desired dimmer

curve setting, and press ENTER.

5. Lastly, you can set your NO DMX setting. This setting is a precaution setting. This setting is used

in the event that the DMX signal is lost or interrupted. Press ENTER when you are finished to

return to the DMX address setting.

Dimmer Curve - This setting will let you select your desired dimmer curve.

1. Press the MODE button until “AXXX” is displayed. “XXX” represents the current displayed

address.

2. Press the SET UP button until “dcXX” is displayed, then press ENTER.

3. 1 of 5 dimming curve settings will be displayed: Standard, Stage, TV, Architectural, or Theatre.

Use the UP and DOWN buttons to select your desired dimming curve and press ENTER to con-

firm. See the Dimmer Curve Chart section of this manual for detailed information.

NO DMX - This setting defines the behavior of the fixture in the event that the DMX signal is

lost, interrupted, or power is lost. It also defines the default mode that the fixture will go into

immediately after powering up.

1. Press the MENU button until “NO DMX” is displayed, and either “Sound”, “Black”, or “Hold” will

be displayed beneath.

2. Press ENTER and the bottom line of text will begin to flash. Use the UP or DOWN buttons to

choose an operating mode.

• Sound - The unit will automatically go into sound active mode.

• Black (Blackout) - The unit will automatically go into stand by mode.

• Hold - The fixture will stay in the last DMX setting. If power is applied and this mode is set,

the unit will automatically go into the last DMX set up.

3. Press ENTER to confirm your desired set up.

Secondary Mode - This will let you set your unit as a secondary unit in a primary/secondary

configuration.

1. Press the MODE button until “Secd” is displayed. Your unit will now follow the Primary unit.

ADJ Products, LLC - www.adj.com - Dotz Par User Manual Page 9

RGB Dimmer Mode - Select your desired color to remain static or adjust the RGB colors to

create your desired color.

1. Plug the fixture in and press the MODE button until “Manual Dimmer” is displayed, and press

ENTER.

2. When “r.XXX” is displayed you are in Red dimming mode. Press the UP and DOWN buttons to

adjust intensity.

3. When “G.XXX” is displayed you are in Green dimming mode. Press the UP and DOWN buttons to

adjust intensity.

4. When “b.XXX” is displayed you are in Blue dimming mode. Press the UP and DOWN buttons to

adjust intensity.

Color Macro - Select your desired color macro to remain static.

1. Press the MODE button until “C-XX” is displayed. “XX” represents the currently used macro num-

ber.

2. Use the UP and DOWN button to scroll through the 32 color macros until you find your desired

color.

Built-In Programs - Select your desired Built-In program.

1. Press the MODE button until “P-XX” is displayed. “XX” represents the currently used program

number. Use the UP and DOWN buttons to scroll through 7 different programs.

2. Press ENTER to move through the various adjustments of each program, and use the UP and

DOWN buttons to make adjustments.

Sound Mode - In this mode the unit will run in sound active mode.

1. Press the MODE button until “Sound Mode” is displayed.

2. Use the UP and DOWN buttons to adjust the sound sensitivity. “0” is the least sensitive, and “30”

is the most sensitive.

RF Active - This menu will let you activate the RF remote control.

1. Press the MODE button until “RFXX” is displayed, then press ENTER. “XX” represents the current

setting, either “on” or “off”.

2. Use the UP or DOWN buttons to activate (On) or deactivate (Off) the remote.

Dotz Par System Menu

ADJ Products, LLC - www.adj.com - Dotz Par User Manual Page 10

Dotz Par Universal DMX Control

Universal DMX Control: This function allows you to use a universal DMX-512 controller to control

the chases and patterns, dimmer and strobe. A DMX controller allows you to create unique pro-

grams tailored to your individual needs. The Dotz Par has 4 DMX channel modes: a 3 Channel Mode,

4 Channel Mode, 5 Channel Mode, & 9 Channel Mode. See the Channel Mode sections of this man-

ual for details.

1. This function will allow you to control each individual fixture’s traits with a standard DMX 512

controller.

2. To run your fixture in DMX mode, follow directions in the System Menu section of this manual to

set your DMX address and DMX Channel mode.

3. Plug in the fixture via the XLR connections to any standard DMX controller.

4. For longer cable runs (more than a 100 feet) use a terminator on the last fixture.

Dotz Par Primary-Secondary Configuration

Primary-Secondary Operation: This function will allow you to link up to 16 units together and oper-

ate without a controller. The units will be sound activated. In Primary-Secondary operation, one unit

will act as the controlling unit and the others will react to the controlling units programs. Any unit can

act as a Primary or as a Secondary.

Using approved DMX data cables, daisy chain your units together via the XLR connector on the rear

of the units. Remember the Male XLR connector is the input and the Female XLR connector is the

output. The first unit in the chain (primary) will use the female XLR connector only, and the last unit in

the chain will use the male XLR connector only. For longer cable runs we suggest a terminator at the

last fixture.

On the Primary unit, set your desired operating mode.

On the secondary units, press the MODE button until “Secd” is displayed.

The secondary units will now follow the primary unit.

Autres manuels pour Dotz Par

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels ADJ Matériel de DJ

ADJ

ADJ Jolt Bar FX Manuel utilisateur

ADJ

ADJ WiFly NE1 Manuel utilisateur

ADJ

ADJ HYDRO BEAM X1 Manuel utilisateur

ADJ

ADJ Focus Spot 5Z Manuel utilisateur

ADJ

ADJ ENCORE FR150Z Manuel utilisateur

ADJ

ADJ ENCORE FR50Z Manuel utilisateur

ADJ

ADJ DOTZ MATRIX Manuel utilisateur

ADJ

ADJ FS3000LED Manuel utilisateur

ADJ

ADJ THEATRIX PRO 48 LED Manuel utilisateur

ADJ

ADJ INNO ROLL HP Manuel utilisateur

ADJ

ADJ SABER SPOT WW Manuel utilisateur

ADJ

ADJ ENCORE BURST 100 IP Manuel utilisateur

ADJ

ADJ HYDRO WASH X7 Manuel utilisateur

ADJ

ADJ 6-PACK SKB CASE Manuel utilisateur

ADJ

ADJ SABER BAR 6 Manuel utilisateur

ADJ

ADJ HEX700 Manuel utilisateur

ADJ

ADJ 1223200047 Mode d’emploi

ADJ

ADJ ADJ FLAT PAR TRI18X Manuel utilisateur

ADJ

ADJ COB CannOn Wash DW Manuel utilisateur

ADJ

ADJ Eliminator Lighting FROST FX BAR W Manuel utilisateur

ADJ

ADJ MEGA HEX PAR Manuel utilisateur

ADJ

ADJ ENTOUR HAZE PRO Manuel utilisateur

ADJ

ADJ INNO POCKET ROLL Manuel utilisateur

ADJ

ADJ Vizi BSW 300 Manuel utilisateur

Manuels Matériel de DJ populaires d'autres marques

ALPHA LITE

ALPHA LITE ALPHA 1500 Manuel du propriétaire

Chauvet

Chauvet OVATION E-930VW Manuel utilisateur

Zumtobel

Zumtobel APHRODITE Home Manuel utilisateur

Snow Masters

Snow Masters Zig Oscillator Manuel utilisateur

EuroLite

EuroLite 50530554 Manuel utilisateur

Beamz

Beamz BUV243 Manuel utilisateur

thomann

thomann Stairville DJ Lase 40-G MK-III Manuel utilisateur

Eagletone

Eagletone 6 Eyes Flower Manuel utilisateur

EuroLite

EuroLite FLD-1508 Manuel utilisateur

Technical Pro

Technical Pro LG8xSEA Manuel utilisateur

JB Systems

JB Systems Lounge Laser DMX Manuel utilisateur

Lightmaxx

Lightmaxx Vega Halo 90 Manuel utilisateur

Elation

Elation FUZE WASH Z350 Manuel utilisateur

Maverick

Maverick MK3 WASH Manuel utilisateur

Infinity

Infinity TF-260C7 Fresnel Manuel utilisateur

Chauvet

Chauvet EVE E-50Z Manuel utilisateur

Eliminator Lighting

Eliminator Lighting E 138 Manuel utilisateur

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Manuel utilisateur