ADInstruments ML206 Manuel utilisateur

iGas Analyzer Owner’s Guide

Gas Analyzer

Owner’s Guide

ii Gas Analyzer Owner’s Guide

is document was, as far as possible, accurate at the time of release. However,

changes may have been made to the soware and hardware it describes since then.

ADInstruments NZ Limited reserves the right to alter specications as required. Late-

breaking information may be supplied separately.

Trademarks of ADInstruments

PowerLab®, LabChart® and ADInstruments® are registered trademarks of ADInstruments

NZ Limited.

Other Trademarks

Apple, Mac and Macintosh are registered trademarks of Apple Computer, Inc.

Windows, Windows 7, Windows 8, Windows 10 and Windows Vista are either registered

trademarks or trademarks of Microso Corporation.

All other trademarks are the property of their respective owners.

Document Number: U-ML206-OG-035C

Date of Issue: 06/20

and ADInstruments are registered trademarks of ADInstruments NZ Limited. Windows

8, Windows 7, Windows 10, Windows Vista and .NET Framework are trademarks of

Microso Corporation. Apple, the Apple logo, MacOS, and Macintosh are trademarks of

Apple Computer Inc. registered in the U.S. and other countries. Acrobat and Adobe are

registered trademarks of Adobe Systems Incorporated. Igor is a trademark of Wavemetrics

Inc. MATLAB is a registered trademark of e MathWorks Inc. Grass is a trademark of

Astro-Med Inc. All other trademarks are the property of their respective owners.

Web: www.adinstruments.com

Manufactured in Australia by:

ADInstruments (Sydney) Pty. Ltd.,

13/22 Lexington Drive

Bella Vista 2153 New South Wales

Technical Support: support.au@adinstruments.com

iii

Contents

Safety Notes 5

1 Overview 13

How to Use is Guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Checking the Gas Analyzer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

e Gas Analyzer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

e Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

e Back Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

2 Using the Gas Analyzer 17

Connecting the Gas Analyzer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Connecting to the PowerLab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Connecting to Other Recorders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Using the Gas Analyzer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Power-up Test of the Gas Analyzer. . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Sample Inlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

3 Care and Maintenance 25

Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

A Technical Details 27

How it Works . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

O2Transducer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

CO2Transducer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Considerations When Using the Gas Analyzer . . . . . . . . . . . . . . . . 29

Contents

iv Gas Analyzer Owner’s Guide

B Troubleshooting 31

C Speciﬁcations 33

Warranty 37

Index 43

Safety Notes

Statement of Intended Use

All products manufactured by ADInstruments are intended for

use in teaching and research applications and environments only.

ADInstruments products are NOT intended to be used as medical

devices or in medical environments. at is, no product supplied by

ADInstruments is intended to be used to diagnose, treat or monitor a

subject. Furthermore no product is intended for the prevention, curing

or alleviation of disease, injury or handicap.

Where a product meets IEC 60601-1 it is under the principle that:

•it is a more rigorous standard than other standards that could

be chosen.

•it provides a high safety level for subjects and operators.

e choice to meet IEC 60601-1 is in no way to be interpreted to mean

that a product:

•is a medical device.

•may be interpreted as a medical device.

•is safe to be used as a medical device.

Safety Notes

6STH Pump Controller Owner’s Guide

Safety Symbols

Devices manufactured by ADInstruments that are designed for direct

connection to humans are tested to IEC 601-1:1998 (including amendments

1 and 2) and 60601-1-2, and carry one or more of the safety symbols below.

ese symbols appear next to those inputs and output connectors that can be

directly connected to human subjects.

BF symbol: Body-

protected equipment

Warning symbol: See

Documentation

e two symbols are:

•BF (body protected) symbol. is means that the input connectors

are suitable for connection to humans provided there is no direct

electrical connection to the heart.

•Warning symbol. e exclamation mark inside a triangle means

that the supplied documentation must be consulted for operating,

cautionary or safety information before using the device.

Further information is available on request.

Bio Amp Safety Instructions

e Bio Amp inputs displaying any of the safety symbols are electrically

isolated from the mains supply in order to prevent current ow that may

otherwise result in injury to the subject. Several points must be observed for

safe operation of the Bio Amp:

•All Bio Amp front-ends (except for the FE138 Octal Bio Amp) and all

PowerLab units with a built-in Bio Amp are supplied with a 3-lead or

5-lead Bio Amp subject cable and lead wire system. e FE138 Octal

Bio Amp is supplied with unshielded lead wires (1.8m). Bio Amps

are only safe for human connection if used with the supplied subject

cable and lead wires.

•All Bio Amp front-ends and PowerLab units with a built-in Bio Amp

are not debrillator-protected. Using the Bio Amp to record signals

Safety Notes

during debrillator discharges may damage the input stages of the

ampliers. is may result in a safety hazard.

•Never use damaged Bio Amp cables or leads. Damaged cables and

leads must always be replaced before any connection to humans is

made.

Isolated Stimulator Safety

Instructions

e Isolated Stimulator outputs from a front-end signal conditioner or

a PowerLab with a built-in isolated stimulator are electrically isolated.

However, they can produce pulses of up to 100 V at up to 20 mA. Injury can

still occur from careless use of these devices. Several points must be observed

for safe operation of the Isolated Stimulator:

•e Isolated Stimulator output must only be used with the supplied

bar stimulus electrode.

•e Isolated Stimulator output must not be used with individual

(physically separate) stimulating electrodes.

•Stimulation must not be applied across the chest or head.

•Do not hold one electrode in each hand.

•Always use a suitable electrode cream or gel and proper skin

preparation to ensure a low-impedance electrode contact. Using

electrodes without electrode cream can result in burns to the skin or

discomfort for the subject.

•Subjects with implantable or external cardiac pacemakers, a cardiac

condition, or a history of epileptic episodes must not be subject to

electrical stimulation.

•Always commence stimulation at the lowest current setting and

slowly increase the current.

•Stop stimulation if the subject experiences pain or discomfort.

•Do not use faulty cables, or those that have exhibited intermittent

faults.

•Do not attempt to measure or record the Isolated Stimulator

waveform while connected to a subject using a PowerLab input or

any other piece of equipment that does not carry the appropriate

safety symbol (see Safety Symbols above).

8STH Pump Controller Owner’s Guide

Always check the status indicator on the front panel. It will always ash green

each time the stimulator delivers a current pulse. A yellow ash indicates

an ‘out-of-compliance’ (OOC) condition that may be due to poor electrode

contact or electrode cream drying up. Always ensure that there is good

electrode contact at all times. Electrodes that are le on a subject for some

time need to be checked for dry contacts. An electrode impedance meter can

be used for this task.

•Always be alert for any adverse physiological eects in the subject. At

the rst sign of a problem, stimulation must be stopped, either from

the soware or by icking down the safety switch on the front panel

of any built-in Isolated Stimulator or the FE180 Stimulus Isolator.

•e FE180 Stimulus Isolator is supplied with a special transformer

plug pack. e plug pack complies with medical safety requirements.

erefore, under no circumstances should any other transformer be

used with the Stimulus Isolator. For a replacement transformer plug

pack please contact your nearest ADInstruments representative.

General Safety Instructions

To achieve the optimal degree of subject and operator safety, consideration

should be given to the following guidelines when setting up a PowerLab

system either as stand-alone equipment or when using PowerLab equipment

in conjunction with other equipment. Failure to do so may compromise the

inherent safety measures designed into PowerLab equipment.

e following guidelines are based on principles outlined in the international

safety standard IEC60601-1-1: General requirements for safety - Collateral

standard: Safety requirements for medical systems. Reference to this standard

is required when setting up a system for human connection.

PowerLab systems (and many other devices) require the connection of a

personal computer for operation. is personal computer should be certied

as complying with IEC60950 and should be located outside a 1.8 m radius

from the subject (so that the subject cannot touch it while connected to

the system). Within this 1.8 m radius, only equipment complying with

IEC60601-1 should be present. Connecting a system in this way obviates

the provision of additional safety measures and the measurement of leakage

currents.

Accompanying documents for each piece of equipment in the system should

be thoroughly examined prior to connection of the system.

Safety Notes

While it is not possible to cover all arrangements of equipment in a system,

some general guidelines for safe use of the equipment are presented below:

•Any electrical equipment which is located within the SUBJECT

AREA should be approved to IEC60601-1.

•Only connect those parts of equipment that are marked as an

APPLIED PART to the subject. APPLIED PARTS may be recognized

by the BF symbol which appear in the Safety Symbols section of

these Safety Notes.

•Never connect parts which are marked as an APPLIED PART to

those which are not marked as APPLIED PARTS.

•Do not touch the subject to which the PowerLab (or its peripherals)

is connected at the same time as making contact with parts of the

PowerLab (or its peripherals) that are not intended for contact to the

subject.

•Cleaning and sterilization of equipment should be performed in

accordance with manufacturer’s instructions. e isolation barrier

may be compromised if manufacturer’s cleaning instructions are not

followed.

•e ambient environment (such as the temperature and relative

humidity) of the system should be kept within the manufacturer’s

specied range or the isolation barrier may be compromised.

•e entry of liquids into equipment may also compromise the

isolation barrier. If spillage occurs, the manufacturer of the aected

equipment should be contacted before using the equipment.

•Many electrical systems (particularly those in metal enclosures)

depend upon the presence of a protective earth for electrical safety.

is is generally provided from the power outlet through a power

cord, but may also be supplied as a dedicated safety earth conductor.

Power cords should never be modied so as to remove the earth

connection. e integrity of the protective earth connection between

each piece of equipment and the protective earth should be veried

regularly by qualied personnel.

•Avoid using multiple portable socket-outlets (such as power boards)

where possible as they provide an inherently less safe environment

with respect to electrical hazards. Individual connection of each

piece of equipment to xed mains socket-outlets is the preferred

means of connection.

If multiple portable socket outlets are used, they are subject to the following

constraints:

•ey shall not be placed on the oor.

10 STH Pump Controller Owner’s Guide

•Additional multiple portable socket outlets or extension cords shall

not be connected to the system.

•ey shall only be used for supplying power to equipment which is

intended to form part of the system.

Cleaning and Sterilization

ADInstruments products may be wiped down with a lint free cloth moistened

with industrial methylated spirit. Refer to the Data Card supplied with

transducers and accessories for specic cleaning and sterilizing instructions.

Preventative Inspection and

Maintenance

PowerLab systems and ADInstruments front-ends are all maintenance-

free and do not require periodic calibration or adjustment to ensure safe

operation. Internal diagnostic soware performs system checks during

power up and will report errors if a signicant problem is found. ere is no

need to open the instrument for inspection or maintenance, and doing so

within the warranty period will void the warranty.

Your PowerLab system can be periodically checked for basic safety by using

an appropriate safety testing device. Tests such as earth leakage, earth

bond, insulation resistance, subject leakage and auxiliary currents and

power cable integrity can all be performed on the PowerLab system without

having to remove the covers. Follow the instructions for the testing device if

performing such tests.

If the PowerLab system is found not to comply with such testing you should

contact your PowerLab representative to arrange for the equipment to be

checked and serviced. Do not attempt to service the device yourself.

Table des matières

Autres manuels ADInstruments Instrument de mesure

ADInstruments

ADInstruments AD3A02 Manuel utilisateur

ADInstruments

ADInstruments Lt Sensors Series Manuel utilisateur

ADInstruments

ADInstruments PowerLab Teaching series Manuel utilisateur

ADInstruments

ADInstruments AD2821A Manuel utilisateur

ADInstruments

ADInstruments AD1000 Manuel utilisateur

ADInstruments

ADInstruments AD2Q02F Manuel utilisateur

ADInstruments

ADInstruments AD8000 Series Manuel utilisateur

ADInstruments

ADInstruments AD210 Manuel utilisateur

ADInstruments

ADInstruments AD2A04 Manuel utilisateur

ADInstruments

ADInstruments DSA2016 Manuel utilisateur

ADInstruments

ADInstruments AD6810 Manuel utilisateur

ADInstruments

ADInstruments AD2817C Manuel utilisateur

ADInstruments

ADInstruments AD5000 Manuel utilisateur

ADInstruments

ADInstruments DIT3343 Manuel utilisateur

ADInstruments

ADInstruments Transducer Series Manuel utilisateur

ADInstruments

ADInstruments DTVLINK-5 Manuel utilisateur

ADInstruments

ADInstruments DTVLINK-T2 Manuel utilisateur

ADInstruments

ADInstruments AD2Q01F Manuel utilisateur

ADInstruments

ADInstruments AD3343 Manuel utilisateur

ADInstruments

ADInstruments AD6830 Manuel utilisateur

ADInstruments

ADInstruments DSA2016TG Manuel utilisateur

ADInstruments

ADInstruments AD6236P Manuel utilisateur

ADInstruments

ADInstruments S7200 Manuel utilisateur

ADInstruments

ADInstruments pH Amp Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur