ADEMCO Galaxy Keyprox Caractéristiques techniques

Galaxy Keyprox

Installation and Programming Instructions

II1-0028 D 2 8/5/02

Contents

Overview..................................................................................................................3

Compatibility............................................................................................................3

Mounting..................................................................................................................3

Wiring ......................................................................................................................4

Configuration ...........................................................................................................4

Keypad Programming ..............................................................................................4

Card Programming...................................................................................................5

Card Self-Learn Procedure.......................................................................................5

Operation..................................................................................................................6

Dual Focus ...........................................................................................................6

Door Control Programming......................................................................................7

Specifications...........................................................................................................8

Declaration of Conformance....................................................................................8

II1-0028 D 3 8/5/02

Overview

The Galaxy Keyprox is a standard Galaxy MK7 keypad and a proximity

card reader, combined into one housing. This allows dual function

setting/unsetting ability from the one station without the need for a separate

card reader. It is primarily intended for use in situations where a PIN and/or

card are needed to set and unset the intruder alarm system. It is not

intended to be used for door control as it does not contain a door strike

relay. However, limited door functions can be programmed using Links

programming in the Galaxy control panels.

Compatibility

The Galaxy Keyprox is intended for use with the Galaxy 8, 18, 60, 128,

500, 504 and 512 panels. The panels must be fitted with software version

1.18 or later.

Most non encrypted HID* cards and standard ASK cards up to 34 Bit can

be read by the Keyprox. Proprietary card type may not be read properly by

the Keyprox

* Note that some versions of the keypad may not have the HID functionality

enabled.

MAX cards or tags can be read by the Keyprox. However if MAX readers

are also used on the system, then the cards will needs to be programmed

on to two separate users, as they are seen in a different way by the MAX

type readers and the Keyprox.

Mounting

The Keyprox should be mounted on a flat vertical surface in a convenient

location. Separate the back plate from the rest of the keypad by gently

pushing on the two locking clips on the base of the Keyprox with a

screwdriver. Place the back plate on the wall at the desired location and

mark the position of the screw holes. Remove the plate then drill the holes

as required. The back plate can then be screwed to the wall while running

the cable connection through the available opening. Once the back plate

has been secured to the wall, the rest of the Keyprox can be clipped in

place by locating the top lugs first, then pushing the lower clips home,

gently but firmly.

II1-0028 D 4 8/5/02

Wiring

The Keyprox must be wired to the RS485 data bus on the Galaxy panel,

maintaining the parallel daisy chain wiring configuration. Only 4

connections are required, +12V, 0V, A and B data. If the Keyprox is the last

module on the A B RS485 data bus, then a 680 ohm end of line resistor

must be fitted across the A and B terminals.

Configuration

The Keyprox is configured onto the Galaxy panel as two separate modules,

a keypad and a MAX reader. Before powering up the Keyprox, the address

must be set using the rotary switch on the back of the PCB. This address

will apply to both the Keypad and the MAX Reader sections. It is the

installer’s responsibility to ensure that the address set is compatible with

the system in use. Not all addresses are acceptable to all Galaxy panels.

Reference to the installation instructions of the Galaxy panel is

recommended.

Once the address has been set and the Keyprox has been powered up, it

must be configured onto the Galaxy system. This is done automatically on

leaving programming mode, or by repowering the system. When configured

correctly, the system will show that two modules have been added, a

keypad and a MAX reader, both with the same address.

Keypad Programming

The keypad side of the Keyprox requires no programming for most

installations. If required, the parameters for the keypad can be altered in

programming menu 58.

II1-0028 D 5 8/5/02

Card Programming

In order for the card reader to operate, the unique serial number

programmed into each card to be used must be programmed to a separate

user on the Galaxy panel. This is done by programming the numbers into

the MAX number section of the user, in menu 42, under the desired user.

This can be simplified by using the self-learn procedure described below.

The card held function needs to be programmed here, to allow the card to

set and unset the system. Refer to the relevant sections in the Galaxy

Panel user or installation manuals for full details. (Menu 42 - codes.)

Card Self-Learn Procedure

Not all proximity cards and tags have the serial numbers printed on them.

However, the card number must be programmed into the Galaxy panel to

allow the card to work. To simply this programming process, a card self-

learn procedure has been included in the Keyprox.

Note: The card self-learn procedure should only be used whilst the

Keyprox is in the user menu for entering the MAX card number and the

panel is waiting for the actual card number to be entered. Use of the self-

learn at other times will result in random menu selections.

Procedure

1. Use the Keyprox to enter menu option 42.1. Select the user to

which the card is to be assigned. Within the user menu, select

option 7=MAX Number.

2. Delete all the digits of the existing number using the B< button.

3. Place the keypad in the Self-Learn mode by holding the A button

and pressing 1 button simultaneously. The keypad will give a

double beep to indicate entry into the Self-Learn mode.

4. Within 3 seconds of the double beep, swipe the new card at the

Keyprox.

5. The card number will appear one the keypad display.

6. Press ENT to save the card number.

7. To enter more cards, repeat the procedure for other users.

Note: The Self-Learn mode will time out after 3 seconds if no card is

presented. During the Self-Learn mode operation, the keypad buttons will

not function.

II1-0028 D 6 8/5/02

Operation

The Keyprox will behave as two separate module. The keypad section will

function as a standard Galaxy Keypad, for setting/unsetting, programming

and general operation.

The Proximity card reader section operates similar to a Galaxy MAX

reader. Swiping a card in front of the read head in the lower right hand

corner of the keypad will be seen as a valid card read by the panel. This

can be utilised if required by using Links on the Galaxy Panel. To perform

the card held function assigned to card user, the card must be held in front

of the read head for at least 3 seconds. A long beep will be heard from the

keypad buzzer and the card held function will be performed.

Dual Focus

Dual Focus means that the PIN and the Card belonging to the same user

must be used together to access the system. This is typically used as a

secure method of setting and unsetting the system. To achieve this, assign

a # to PIN of the user and to the MAX number. Assign an appropriate MAX

function, for example, 12=Timed set. To the system now, a user would

have to enter their PIN, then hold the card in front of the reader for 3

seconds to begine setting the system. To unset, simply enter the PIN then

briefly swipe the card in front of the reader.

Door Control Programming

Door control functionality can be achieved by setting up zones, outputs and

links on the Galaxy panel as shown in the example below.

Keyprox

(Addr 0)

Door Contact Zone 1011

Door Release on output 1011

Egress button inside,

on zone 1012

Zone 1011 is programmed as a Security zone.

Zone 1012 is programmed as a Link zone.

Output 1011 is programmed as Link-A type, mode=pulse 5 Sec.

Output 1012 is programmed as Link-B (door open time out), pulse 15 Sec.

Keyprox is on address 00 (MAX 10)

Program the following links:

1. Source MAX 10 Destination Link-A

2. Source MAX 10 Destination Link-B

3. Source #1012 Destination Zone 1011

4. Source Zone 1012 Destination Link-A

5. Source Zone 1012 Destination Link-B

This will program the door to unlock for 5 seconds and allow it to stay open

for 15 seconds from whenever a valid card is swiped at the Keyprox. Zone

1012 is programmed as an Egress button which will open the door in the

same way as a valid card swipe.

If the door is forced, a standard zone alarm will occur.

II1-0028 D 7 8/5/02

Specifications

Dimensions 148 x 90 x 31mm

Weight 225g

Operating Temp -10oC to 40oC*

Proximity Reader 125KHz, Inductive

Read range 25mm minimum

Current Draw Typical, 90mA

Maximum, 140mA

*Note: The display may not operate correctly at temperatures below 0oC.

However the Keyprox will still continue to operate on the system.

Declaration of Conformance

Declaration of Conformity

Hereby, Ademco Microtech declares that this Galaxy Keyprox

card reader is in compliance with the essential requirements and

other relevant provisions of Directive 1999/5/EC.

This device is intended for use in the following countries:

Austria Belgium Denmark Finland

France Germany Iceland Ireland

Italy Luxembourg Netherlands Norway

Portugal Spain Sweden Switzerland

United Kingdom

II1-0028 D 8 8/5/02

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels ADEMCO Clavier

ADEMCO

ADEMCO 6128RF Manuel utilisateur

ADEMCO

ADEMCO 6137 Manuel utilisateur

ADEMCO

ADEMCO 7720P Manuel utilisateur

ADEMCO

ADEMCO 6128RF Manuel utilisateur

ADEMCO

ADEMCO 6148 Manuel utilisateur

ADEMCO

ADEMCO Galant 6128 RFH Manuel de la liste des pièces

ADEMCO

ADEMCO 6270 - Ademco TouchCenter Keypad Manuel utilisateur

ADEMCO

ADEMCO 6150PL3 Manuel utilisateur

ADEMCO

ADEMCO TeleSmart Manuel utilisateur

ADEMCO

ADEMCO Vista 128 Manuel utilisateur

ADEMCO

ADEMCO Galant 6128 RFH Manuel utilisateur

ADEMCO

ADEMCO 6139 Manuel utilisateur

ADEMCO

ADEMCO 6148ICON Instructions de montage

ADEMCO

ADEMCO 6128WL Manuel utilisateur

ADEMCO

ADEMCO 6270 - Ademco TouchCenter Keypad Instructions de montage

ADEMCO

ADEMCO Galant 6128 RFH Manuel utilisateur

ADEMCO

ADEMCO 6128RF Manuel utilisateur

ADEMCO

ADEMCO 4111XM Manuel utilisateur

ADEMCO

ADEMCO Alpha Console 5330 Manuel utilisateur

ADEMCO

ADEMCO 6150RF Manuel utilisateur

ADEMCO

ADEMCO Galant 6128 RFH Manuel utilisateur

ADEMCO

ADEMCO 4137AD Manuel utilisateur

ADEMCO

ADEMCO 5828 Manuel utilisateur

ADEMCO

ADEMCO 6160CR Manuel utilisateur

Manuels Clavier populaires d'autres marques

BFT

BFT SELETTO Manuel utilisateur

Micro Id

Micro Id MP7G3BL Manuel d'instructions

WindowMaster

WindowMaster WLI 130 Manuel utilisateur

ACT

ACT ACT PRO 1030 Manuel utilisateur

Cardin

Cardin SSB Series Manuel utilisateur

Harman Kardon

Harman Kardon KP 1 Manuel utilisateur

Chamberlain

Chamberlain KPR2000 Guide de l'utilisateur

CYP

CYP CR-KP1 Manuel utilisateur

Aeware

Aeware k-35 Series Guide de référence

Aritech

Aritech CS-175 Series Manuel utilisateur

GE NetworX NX-1600E Series Manuel utilisateur

Lenze AC Tech

Lenze AC Tech MC SERIES Manuel utilisateur

Burg Wächter

Burg Wächter secuENTRY 7711 Manuel utilisateur

Aeware

Aeware in.k450 Manuel utilisateur

Lenze

Lenze EPM-H410 Manuel utilisateur

Toshiba

Toshiba RKP007Z Manuel utilisateur

Gemini

Gemini GEM-DXK1 KEYPAD Manuel utilisateur

Russound

Russound MDK-C5 Manuel d'utilisation