Addonics Technologies RMRSAI Manuel utilisateur
Addonics
T E C H N O L O G I E S
Ruby Mobile Rack
RMRSAI & RMRSASC
User’s Guide
Version 1.0
FCC Warning Statement
This equipment has been tested and found to comply with the limits for a class B digital
device pursuant to Part 15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy. If not installed and
used in accordance with the instructions, it may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If the equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment on and off, the user
is encouraged to try and correct the interference by one or more of the following
suggestions.
Reorient or relocate the receiving antenna
Increase the distance between the equipment and the receiver
Connect the equipment to a different power outlet other than the one where receiver is
connected
Consult a certified television or radio technician
Enclosure Overview
Step 1 Separate the top from the bottom cover of the drive enclosure by
loosening the screw as shown on the photo.
Step 2 Align the SATA connector in the 2.5” hard drive with the SATA connector
on the PCB.
Step 3 Wrap the shock absorbers around the hard drive and PCB.
shock
absorbers
PCB
top cover
2.5” SATA
hard drive
bottom cover
switch
Step 4 Turn over the PCB and secure the hard drive to the PCB with the
mounting screws that come with the kit.
Step 5 Mount the board to the bottom cover.
Step 6 Put the top cover on by holding it in near vertical position and sliding the
two metal clips inside the two small slots on the rear of the bottom cover.
Step 7 Lower the front of the top cover and making sure the two covers lined up
properly. Tighten the small retaining screw on the front of the bottom cover to
close the enclosure.
Ruby Enclosure
Switch:
INT: This mode is used when the enclosure is placed inside a drive
cradle. For mobile rack kits, this is the mode used.
EXT: This mode is used if the enclosure is used as an external hard
drive.
Ruby Drive Cradle
Note: You can only use one power connector at a time. Either use the 4-pin
Molex or 15-pin SATA connector but do not simultaneously use them.
Mounting holes for
3 ½” drive bay
15-pin SATA
power connector
4-pin Molex
power connector
Power LED and
Drive Access LED
Switch
7-pin SATA
data connector
Model: RMRSAI
This Ruby model will not hot-swap. Slide the Ruby enclosure inside the cradle
and then place switch on INT position before the system can be turned ON.
Step 1: Connect the SATA to IDE converter to the SATA interface of the
cradle.
Step 2: Connect the Y-cable that came with converter to the 4-pin floppy
connector on the converter. The other end would connect to your
system’s power supply. This power connection provides power to both
converter and the ruby mobile rack.
Step 3: Attach the IDE ribbon cable connected to your IDE primary
channel to the 40-pin connector on the adapter.
Model: RMRSASC
This Ruby model will not hot-swap. Slide the Ruby enclosure inside the cradle
and then place switch on INT position before the system can be turned ON.
Step 1: Connect the SATA to SCSI converter to the SATA interface of
the cradle.
Step 2: Connect the Y-cable that came with converter to the 4-pin floppy
connector on the converter. The other end would connect to your
system’s power supply. This power connection provides power to both
converter and the ruby mobile rack.
Step 3: Attach the SCSI ribbon cable connected to your SCSI host
adapter to the 68-pin connector on the adapter.
Y-cable
Connects to
power supply
SATA to IDE
converter
40-pin IDE
connector
68-pin SCSI
connector
SATA to SCSI
converter
4-pin Floppy
power connector
40-pin IDE
connector
Technical Support
If you need assistance to get your unit functioning properly, please call Addonics
Technical Support. Our technical staff will be happy to assist you, but they will
need your help to do so. Calling the technical support staff without all the proper
information can be both time consuming and frustrating. Here are some tips to
help you out:
MODEL NUMBER –Please have this number on hand.
SYSTEM INFORMATION –Type of computer, peripherals, etc.
OPERATING SYSTEM –What version of Windows
WHAT’S THE TROUBLE? – Give enough information
about your problem so that we can recreate and diagnose it.
FREE Software Drivers for all Addonics Technologies
Products are available 24 hours per day at the
World Wide Web Site: www.addonics.com.
Contact Information
Phone: 408-433-3899
Fax: 408-433-3898
Email: http://www.addonics.com/sales/query/
Internet: http://www.addonics.com
TECHNICAL SUPPORT
Phone: 408-433-3855
Hours: 8:30 am - 6:00 pm PST
Email: http://www.addonics.com/support/query/
Power connection
using 5V power adapter
or USB power cable
Connects to
power supply
Ce manuel convient aux modèles suivants
1
Autres manuels Addonics Technologies Support et étagère
Manuels Support et étagère populaires d'autres marques
Salamander
Salamander Acadia AC/W/L400/WH Manuel utilisateur
Fohhn
Fohhn VAT-09 Guide de l'utilisateur
ricoo
ricoo FS0522 Manuel utilisateur
AMSOIL
AMSOIL BMK-22 Guide rapide
Kargo Master
Kargo Master 48220 Manuel utilisateur
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur
