ADC NG3 Manuel utilisateur
ADCP-90-299
Issue 3
October 2007
1402789 Rev A
NG3™High-Density Fiber Distribution
Frame System Rack Installation Manual:
Concrete Floor
21870-A
ADCP-90-299 • Issue 3 • October 2007 • Preface
Page ii
COPYRIGHT
© 2007, ADC Telecommunications, Inc.
All Rights Reserved
REVISION HISTORY
LIST OF CHANGES
The technical changes incorporated into this issue are listed below.
TRADEMARK INFORMATION
ADC and ADC Telecommunications are registered trademarks of ADC Telecommunications, Inc.
NG3 is a trademark of ADC Telecommunications, Inc.
DISCLAIMER OF LIABILITY
Contents herein are current as of the date of publication. ADC reserves the right to change the contents without prior notice. In no
event shall ADC be liable for any damages resulting from loss of data, loss of use, or loss of profits and ADC further
disclaims any and all liability for indirect, incidental, special, consequential or other similar damages. This disclaimer of
liability applies to all products, publications and services during and after the warranty period.
This publication may be verified at any time by contacting ADC’s Technical Assistance Center at 1-800-366-3891, extension 73475
(in U.S.A. or Canada) or 952-917-3475 (outside U.S.A. and Canada), or by e-mail to bcg_ta[email protected].
ISSUE DATE REASON FOR CHANGE
1 02/2003 Original
2 06/2003 Added brackets for securing two racks.
3 10/2007 Updated drawings as needed with redesigned rack assembly
PAGE IDENTIFIER DESCRIPTION OF CHANGE
4 Dwg 1 Updated existing drawing with redesigned rack assembly.
9-15 Dwgs 7-12 Updated existing drawing with redesigned rack assembly.
16 Dwg 1 Updated existing drawing with redesigned rack assembly.
17-18 Dwgs 1-2 Updated existing drawing with redesigned rack assembly.
ADC Telecommunications, Inc.
P.O. Box 1101, Minneapolis, Minnesota 55440-1101
In U.S.A. and Canada: 1-800-366-3891
Outside U.S.A. and Canada: (952) 938-8080
Fax: (952) 917-1717
ADCP-90-299 • Issue 3 • October 2007 • Preface
Page iii
© 2007, ADC Telecommunications, Inc.
TABLE OF CONTENTS
Content Page
ABOUT THIS MANUAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v
RELATED PUBLICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v
ADMONISHMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .vi
GENERAL SAFETY PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .vi
LIST OF ACRONYMS AND ABBREVIATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .vi
1 TOOLS AND MATERIALS REQUIRED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
2 MOUNTING THE RACK ON A CONCRETE SURFACE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3 GROUNDING THE RACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
4 SECURING TWO RACKS TOGETHER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
5 CUSTOMER INFORMATION AND ASSISTANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
ADCP-90-299 • Issue 3 • October 2007 • Preface
Page iv
© 2007, ADC Telecommunications, Inc.
TABLE OF CONTENTS
Content Page
Blank
ADCP-90-299 • Issue 3 • October 2007 • Preface
Page v
© 2007, ADC Telecommunications, Inc.
ABOUT THIS MANUAL
This manual provides complete instructions for installing an NG3 rack on a concrete floor,
grounding the rack, and securing two racks.
RELATED PUBLICATIONS
Listed below are related manuals and their publication numbers. Copies of these publications can
be ordered by contacting the ADC Technical Assistance Center at 1-800-366-3891 (in U.S.A. or
Canada) or 952-917-3475 (outside U.S.A. and Canada).
NG3 High-Density Fiber Distribution Frame System
Installation Manual: Raised Floor 90-295
Provides pictorial instructions for installing an NG3 rack on a raised floor and grounding the
rack.
NG3 High-Density Fiber Distribution Frame System Patch Cord Routing Guide 90-296
Provides pictorial guidelines for routing patch cords on a lineup consisting of
one or more NG3 frames. This manual consists of laminated cards that hang on
the lineup.
NG3 High-Density 72 Position Hinged Termination Panel User Manual 90-297
Provides installation and operation instructions for the NG3 termination panel.
NG3 High-Density Fiber Distribution Frame System User Manual 90-298
Contains an NG3 system overview and information for planning and operating
the system.
Title/Description ADCP Number
ADCP-90-299 • Issue A • June 2001 • Preface
Page vi
© 2007, ADC Telecommunications, Inc.
ADMONISHMENTS
Important safety admonishments are used throughout this manual to warn of possible hazards to
persons or equipment. An admonishment identifies a possible hazard and then explains what
may happen if the hazard is not avoided. The admonishments — in the form of Dangers,
Warnings, and Cautions — must be followed at all times. These warnings are flagged by use of
the triangular alert icon (seen below), and are listed in descending order of severity of injury or
damage and likelihood of occurrence.
GENERAL SAFETY PRECAUTIONS
LIST OF ACRONYMS AND ABBREVIATIONS
The following acronyms are used in this manual:
FOT Fiber Optic Terminal
IFC Intra Facility Cable
NG3 New Generation High-Density Fiber Distribution Frame
OSP Outside Plant
Danger: Danger is used to indicate the presence of a hazard that will cause severe personal
injury, death, or substantial property damage if the hazard is not avoided.
Warning: Warning is used to indicate the presence of a hazard that can cause severe personal
injury, death, or substantial property damage if the hazard is not avoided.
Caution: Caution is used to indicate the presence of a hazard that will or can cause minor
personal injury or property damage if the hazard is not avoided.
Danger: Infrared radiation is invisible and can seriously damage the retina of the eye. Do not
look into the ends of any optical fiber. Do not look directly into the optical adapters of the
adapter packs. Exposure to invisible laser radiation may result. An optical power meter should
be used to verify active fibers. A protective cap or hood MUST be immediately placed over any
radiating adapter or optical fiber connector to avoid the potential of dangerous amounts of
radiation exposure. This practice also prevents dirt particles from entering the adapter or
connector.
ADCP-90-299 • Issue 3 • October 2007
Page 1
© 2007, ADC Telecommunications, Inc.
1 TOOLS AND MATERIALS REQUIRED
The tools and materials required for mounting the NG3 Frame System Rack on a concrete
surface are specified in Table 1, Table 2, and Table 3.
Table 1. Tools Required
TOOL PICTURE
Adjustable wrenches (2)
0.25 to 1 inch (8 to 25.4 mm)
Crow bar
Drill with metal and concrete drill bits
0.25 to 1 inch (8 to 25.4 mm)
Ruler or tape measure
Torque wrench
19.9 ft.-lbs. (27 Nm)
Allen wrench (5/16-inch)
Note: Used for leveling rack
Hammer
Set of combination open-end/box-end
wrenches
0.25 to 1 inch (8 to 25.4 mm)
12494-B
12495-B
12496-B
cm
131
12825-a
17721-A
18406-A
12500-B
12506-B
ADCP-90-299 • Issue 3 • October 2007
Page 2
© 2007, ADC Telecommunications, Inc.
Set of sockets
0.25 to 1 inch (8 to 25.4 mm)
Crimping tool
0.25 to 0.3 inches (6.35 to 7.62 mm)
Note: Used for grounding rack
Vacuum
Flat tip (–) and Phillips (+) screwdrivers
(#1, #2, and #3)
Table 2. Ground Wire Kit Components (Accessory)
ITEM DESCRIPTION/PICTURE
Ground cable (13 ft.) #6 AWG (4.1 mm) solid copper wire
Nylon cable clamps (8)
12-24 x 0.5 inch screws
2-hole copper compression lug (1) with
0.75-inch hole spacing.
Note: Accommodates #6 AWG wire
Table 1. Tools Required, continued
TOOL PICTURE
12504-B
12824-A
12505-B
12503-B
18413-A
18414-A
12498-B
ADCP-90-299 • Issue 3 • October 2007
Page 3
© 2007, ADC Telecommunications, Inc.
Table 3. Fasteners Shipped with Rack
PART PICTURE
Anchor bolt assembly (4)
Hold-down washer (4)
STUD
TORQUE LIMITING HEX NUT
METAL SLEEVE
NYLON SPACER
EXPANDABLE CONE
FLAT WASHER
TOP FLANGE
(SHEARS OFF)
PLASTIC COVER
NOTE: ONE PIECE
TORQUE NUT
18008-B
21899-A
ADCP-90-299 • Issue 3 • October 2007
Page 4
© 2007, ADC Telecommunications, Inc.
2 MOUNTING THE RACK ON A CONCRETE SURFACE
To mount the rack on a concrete surface, follow the instructions in drawings 1 through 12.
18591-B
REAR AISLE
(3-FEET
RECOMMENDED
MINIMUM)
FRONT AISLE
(4-FEET
RECOMMENDED
MINIMUM)
1
Determine rack location.
18592-B
PENCIL
MARK CENTER OF SLOTS
2Place template/isolation pad on concrete
floor location and mark concrete.
Autres manuels pour NG3
1
Table des matières
Autres manuels ADC Support et étagère
Manuels Support et étagère populaires d'autres marques
Salamander
Salamander Acadia AC/W/L400/WH Manuel utilisateur
Fohhn
Fohhn VAT-09 Guide de l'utilisateur
ricoo
ricoo FS0522 Manuel utilisateur
AMSOIL
AMSOIL BMK-22 Guide rapide
Kargo Master
Kargo Master 48220 Manuel utilisateur
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur
