Adaptive Technologies Group WM-0-15-60 Manuel utilisateur

Installation Guide WM-0-15-60

Speaker Wall Mount

The WM-0-15-60 wall mount is an excellent choice for various wall mounting positions as

well as 0° and 15° speaker tilt angles. The speaker are secured to standard loud speaker

mounting hole patterns, 5”x2.75” and 4” x 2.25” located on the rear of the speaker

cabinets. This mount secures to speakers by way of standard 4 hole mounting pattern

including 5” X 2 3/4 and 4 X 2 1/4 located on the rear panel of speaker cabinet.

Contents:

Be sure that all of the following items are included in this kit before proceeding:

1 pc wall mounting plate

1 pc speaker adapter assembly

1 pc hardware kit assembly

1 pc instruction sheet

Notes:

Screws and washer to attach wall mount assembly to wall are not included.

Screws and washer to attach speaker adapter to speaker are not included

Installation Procedure:

Step 1: The speaker tilt angle can be selected from either 0° or15°.

For 0° the wall mount tube is facing up, for 15° the wall mount tube is

facing down (Figure 1 and Figure 2)

Step 2: Secure the wall plate assembly to the wall

with the appropriate mounting hardware, hardware

not included (Figure 2).

Figure1

Figure2

Adaptive Technologies Group

1635 E. Burnett Street | Signal Hill, CA 90755 USA

Ph: 562.424.1100 | Fax: 562.424.3520

www.adapttechgroup.com

ALWAYS INSTALL SAFETY CABLES

WARNING: Mounting and/or suspension of audio and video equipment requires

experienced professionals. Improperly installed loudspeakers can result in property

damage, personal injury and/or liability to the installing contractor.

Step 3: Secure speaker to the speaker adapter plate

assembly with the opening of the channel facing up.

Align the speaker’s four mounting points with the

mount’s matching hole pattern. Use the speaker

manufacturer’s recommended fasteners; tighten

fasteners permanently through the mount and into the

speaker cabinet (Figure 3).

Step 4: Speaker arm assembly mounting options

range from 5.05” to 7.05” for 0° and 5.83” to 7.83” for

15° depending upon the hole used (Figure 4A and

4B).

Step 5: Attach the speaker adapter w/ speaker to

the wall mount assembly hole using 1/4-20 hex

head screw, nylon nut and at washer. Tighten

permanently. (Figure 5)

Step 6: Connect signal wire to the speaker terminals.

Step 7: Always Install Safety Cables

Install safety cable Attach a safety cable (sold

separately) to the mounting surface (must be able to

support at least ve times the weight of the speaker),

then attach the other end of the safety cable to the

speaker. If no attachment is provided on speaker,

consult speaker manufacturer for advice on best

attachment point and method.

Installation Guide

Note to installers:

Due to the wide variety of wall structures, materials and mounting methods, the installing contractor must exercise proper judgment in selecting

the mounting area and hardware.

As a guide, the installation, when complete should be capable of supporting 5 to 10 times the actual applied load. Always use a backup safety

system such as a safety cable.

To assure a trouble-free installation, read through and follow these instructions carefully before beginning. If you have doubts about the integrity of

the structure you are mounting to or you are not sure about the proper hardware to use, consult a structural and/or hardware specialist.

Caution: Due to the wide variety of structures, environments, materials and rigging methods, the installing contractor must exercise good

judgment in selecting the proper mounting area and hardware.

Figure3 Figure4A (0° Tilt)

Figure4B (15° Tilt)

Figure5

Adaptive Technologies Group

1635 E. Burnett Street | Signal Hill, CA 90755 USA

Ph: 562.424.1100 | Fax: 562.424.3520

www.adapttechgroup.com

ALWAYS INSTALL SAFETY CABLES

WARNING: Mounting and/or suspension of audio and video equipment requires

experienced professionals. Improperly installed loudspeakers can result in property

damage, personal injury and/or liability to the installing contractor.

PM-BAND-SERIES

PoleStar Pole Banding Kit 30” - 90”

Autres manuels Adaptive Technologies Group Support et étagère

Adaptive Technologies Group

Adaptive Technologies Group MultiMount MM-120 Manuel utilisateur

Adaptive Technologies Group

Adaptive Technologies Group MM-3RDX-18 Manuel utilisateur

Adaptive Technologies Group

Adaptive Technologies Group MultiMount MM-023 Manuel utilisateur

Adaptive Technologies Group

Adaptive Technologies Group MM-016-BT Manuel utilisateur

Adaptive Technologies Group

Adaptive Technologies Group MM-3RDX-120 Manuel utilisateur

Adaptive Technologies Group

Adaptive Technologies Group SAS-100-CA Manuel utilisateur

Adaptive Technologies Group

Adaptive Technologies Group SAS-2WA-Series Manuel utilisateur

Adaptive Technologies Group

Adaptive Technologies Group UB-QX500 Instructions d'utilisation et d'entretien

Adaptive Technologies Group

Adaptive Technologies Group MultiMount MM-024 Manuel utilisateur

Manuels Support et étagère populaires d'autres marques

Salamander

Salamander Acadia AC/W/L400/WH Manuel utilisateur

Fohhn

Fohhn VAT-09 Guide de l'utilisateur

ricoo

ricoo FS0522 Manuel utilisateur

AMSOIL

AMSOIL BMK-22 Guide rapide

Kargo Master

Kargo Master 48220 Manuel utilisateur

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur

ricoo

ricoo S1222 Manuel utilisateur

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manuel utilisateur

VidaBox

VidaBox VB MNT FFS2 Manuel utilisateur

Welch Allyn

Welch Allyn 48960 Manuel utilisateur

Arkon

Arkon CM035-ST-2 Manuel utilisateur

PROEL

PROEL PLWIN60C Manuel utilisateur

Agilent Technologies

Agilent Technologies E2609B Manuel utilisateur

Mustang

Mustang MV-ARM4 Manuel utilisateur

Mounting Solutions

Mounting Solutions WRM-320 Manuel utilisateur

Pyle

Pyle PMKSPAD1 Manuel utilisateur

ShelterIt

ShelterIt 21208 Manuel utilisateur

SPL

SPL RackPack?4 1040 Manuel utilisateur