Adam Equipment MDW-250L Manuel utilisateur

Adam Equipment

MDW-250L

DIGITAL PHYSICIAN SCALE

(P.N. 4302, Rev. B4, January 2006)

1.0 INTRODUCTION

•The MDW 250L scale is a

Digital Physician Scale.

•It is an accurate

electronic device with

advanced design and

stable performance.

•It is designed to measure

both the weight and the

height of a person.

2.0 TECHNICAL SPECIFICATIONS

Maximum capacity 250 kg

Minimum capacity 2 kg

Scale division 100 g

Height range 80 cm-210 cm

Division of measurement 0.5 cm

Accuracy class

Display LCD

Size of platform 372 X 272 mm

Overall dimension 535 X 275 X 940 mm

Deadweight 13 kg

Environment for Use Temperature: 5ºC-40ºC;

Humidity: <85℅RH

Power AC 220V through an adapter

Battery Internal, re-chargeable

6V, 5 hours approx.

3.0 DISPLAY AND KEY DESCRIPTIONS

KEYS FUNCTIONS

[On/Off] To turn the scale on or off.

[Hold] To lock the reading even if the person to be weighed is moving.

[Tare/Zero]

To zero the scale if the display drifts from zero.

To tare the scale, if necessary.

[Func] To set up the service parameters

[kg/ lb] To switch the weighing unit between Kg and lb

DISPLAY DESCRIPTIONS

Zero The arrow above Zero will be displayed when the scale reaches zero.

Stab To indicate that the weighing result is stable

Tare To indicate the scale is tared

Hold This indicates the Hold function is enabled

lb To indicate the reading is in lb

kg To indicate the reading is in kg

The arrow indicator will point at kg, lb, Hold, Tare, Stab or/and Zero

marked below the LCD panel, as on when they are chosen.

When the adapter is connected to recharge the battery, it will show a

red indicator.

4.0 SETTING UP THE SCALE

•Take the Physician scale out of the box.

•Remove the three screws from the bottom of the pillar.

•Place and rotate the pillar and secure it to an upright position

using the three screws and connect the cable by fixing the

connector.

•Slide the pole cover to the bottom.

•Remove the screw at the top of the pillar and turn the

indicator panel to 180 degree. Tighten the screw until the

indicator panel is secured.

•Position the height measuring rod and secure it by fixing its

threaded end.

•Connect the adapter power supply to the main power supply

and put the switch at the rear of the scale to ON.

5.0 WEIGHING

•Place the Physician Scale on an even floor and press the

[On/Off] key.

•The instrument performs a self-test after which it is ready for

operation. The display will show “

0.0

” with an arrow symbol,

above kg or lb, indicating the last chosen unit.

•The arrow above Stab will be on when the reading is stable.

•Press the [On/Off] key to switch off the scale. If the scale is

not to be used for a long time, the main power switch should

be turned off to save the battery life.

•To start weighing, press [On/Off], the scale will show “0.0”.

•If the scale is still displaying a small weight when there is no

load on the platform, it needs to be zeroed. Press the

[Tare/Zero] key to zero the display. The arrow above Zero

will be on. If the zero display is not achieved then the scale

may need to be re-calibrated.

•If the weighing value is to be tared to obtain the net value,

press [Tare/Zero] again. The arrow above Tare will be on.

•The person to be weighed can step on to the platform now.

The weight will be displayed in Kg or lb depending on the

units chosen by the user.

•Units: Press the [kg/lb] key for changing the weighing unit to

kg or lb. An arrow will indicate towards the chosen unit.

•Backlight: The scale has an automatic back-light which is

switched on whenever time the scale is in use.

•Overload display: When “OL” appears on the display, it

shows that the load on the platform is over the maximum

capacity. It is necessary to reduce the load otherwise the

sensor or the platform may be damaged.

•Hold Function: To lock the weighing result, press the [Hold]

key. The arrow indicator will point towards Hold and it will

show a steady reading even if the person on the platform is

moving or goes away from the scale and will not allow the

next weighing. To release the function, press [Hold] again.

•Do not press the [On/Off] key if you do not want to weigh as

pressing the [On/Off] key will switch the scale to ON.

6.0

MEASURING HEIGHT

•While measuring the height, it is necessary to pull up the

measuring board at a right angle with the inside tube.

•When the tube is pulled out straight, it is sufficient to

measure the height from 80 to 126 cm. The number can be

obtained upon the conjoint place where the upper part of

middle tube screw meets with the inside tube scale.

•Further, if the middle tube is pulled out straight, it is possible

to measure the height from 126-190 cm. The reading can be

obtained at the conjoint place where the upper part of outside

tube screw meets with the middle tube scale.

7.0 MAINTENANCE

•Do not dismantle the weighing machine without following the

necessary instructions.

•Do not jump while standing on the load-bearing board. This

may damage the sensor inside.

•Do not move the weighing machine violently and abruptly. It is

recommended to move and put down the weighing machine

gently.

•It is suggested to wipe the stains with soft cloth soaked with

detergent and to wipe later with soft cloth too. Do not use

organic solutions and boiled water to wipe the stains. Do not

use water for cleaning.

•Keep the weighing machine in a dry and clean environment. Do

not expose it outdoor or use it in locations near fire, under

direct sunshine or with high temperature.

•When lifting the height meter, it is suggested to pull it straight

along the pipe without using excessive force.

•The [On/Off] key on the screen board only switches off the

screen power instead of the entire power to the weighing

machine. Therefore, it is necessary to switch off the main

power supply when the weighing machine is not in use for a

long time. Otherwise the battery may be damaged as a result of

over-discharge.

Manufacturer’s Declaration of Conformity

This product has been manufactured in accordance with the harmonised European

standards, following the provisions of the below stated directives:

Electro Magnetic Compatibility Directive 89/336/EEC

Low Voltage Directive 73/23/EEC

Adam Equipment Co. Ltd.

Bond Avenue

Denbigh East Estate

Milton Keynes, MK1 1SW

United Kingdom

FCC COMPLIANCE

This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in a

commercial environment. The equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with the instruction manual,

may cause harmful interference to radio communications. Operation of this equipment in a

residential area is likely to cause harmful interference in which case the user will be

required to correct the interference at his own expense.

Shielded interconnect cables must be employed with this equipment to insure compliance

with the pertinent RF emission limits governing this device.

Changes or modifications not expressly approved by Adam Equipment could void the

user's authority to operate the equipment.

ADAM EQUIPMENT is an ISO 9001:2000 certified global organisation with more

than 30 years experience in the production and sale of electronic weighing

equipments. Products are sold through a world wide distributor network -supported

from our company locations in the UK, USA, SOUTH AFRICA and CHINA. The

company and their distributors offer a full range of Technical Services such as on site

and workshop repair, preventative maintenance and calibration facilities.

ADAM’s products are predominantly designed for the Laboratory, Educational,

Medical and Industrial Segments. The product range can be classified as follows:

−Analytical and Precision Laboratory Balances

−Top Loading Scales for Educational establishments

−Counting Scales for Industrial and Warehouse applications

−Digital Weighing/Check-weighing Scales

−High performance Platform Scales with extensive software

features including parts counting, percent weighing etc.

−Crane scales for heavy-duty industrial weighing

−Digital Electronic Scales for Medical use

−Retail Scales for price computing

Adam Equipment Co. Ltd.

Bond Avenue

Milton Keynes

MK1 1SW

Phone:+44 (0)1908 274545

Fax: +44 (0)1908 641339

e-mail:

sales@adamequipment.co.uk

Adam Equipment Inc.

26, Commerce Drive

Danbury, CT

06810

USA

Phone: +1 203 790 4774

Fax: +1 203 792 3406

e-mail:

sales@adamequipment.com

Adam Equipment S.A. (Pty) Ltd.

P.O. Box 1422

Kempton Park 1620

Johannesburg

Republic of South Africa

Phone +27 (0)11 974 9745

Fax: +27 (0)11 392 2587

e-mail:

sales@adamequipment.co.za

may be reprinted or translated in any form or by any means without the prior permission

of Adam Equipment.

Adam Equipment reserves the right to make changes to the technology, features,

specifications and design of the equipment without notice.

All information contained within this publication was to the best of our knowledge timely,

complete and accurate when issued. However, we are not responsible for

misimpressions which may result form the reading of this material.

The latest version of this publication can be found on our Website.

Visit us at

www.adamequipment.com

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Adam Equipment Échelle

Adam Equipment

Adam Equipment UG119 Manuel utilisateur

Adam Equipment

Adam Equipment CCT Series Manuel utilisateur

Adam Equipment

Adam Equipment CPWplus 6 Manuel utilisateur

Adam Equipment

Adam Equipment MUW Manuel utilisateur

Adam Equipment

Adam Equipment AZextra Series Manuel utilisateur

Adam Equipment

Adam Equipment LBK-3/6a Manuel utilisateur

Adam Equipment

Adam Equipment AQ Series Manuel utilisateur

Adam Equipment

Adam Equipment ECLIPSE Manuel utilisateur

Adam Equipment

Adam Equipment CBD Series Manuel utilisateur

Adam Equipment

Adam Equipment Warrior Series Manuel utilisateur

Adam Equipment

Adam Equipment DUNE SERIES Manuel utilisateur

Adam Equipment

Adam Equipment CCSA series Manuel utilisateur

Adam Equipment

Adam Equipment AEA Series Manuel utilisateur

Adam Equipment

Adam Equipment CBC SERIES Manuel utilisateur

Adam Equipment

Adam Equipment MUW 300L Manuel utilisateur

Adam Equipment

Adam Equipment pgw series Manuel utilisateur

Adam Equipment

Adam Equipment MDW-160M Manuel utilisateur

Adam Equipment

Adam Equipment NETS ME Price Manuel utilisateur

Adam Equipment

Adam Equipment 103 Manuel utilisateur

Adam Equipment

Adam Equipment HCB-J Jewellery Series Manuel utilisateur

Adam Equipment

Adam Equipment WBW Series Manuel utilisateur

Adam Equipment

Adam Equipment WBZ 3 Manuel utilisateur

Adam Equipment

Adam Equipment CBD 100a Manuel utilisateur

Adam Equipment

Adam Equipment CBC SERIES Manuel utilisateur

Manuels Échelle populaires d'autres marques

AWS

AWS ZEO-50 Manuel utilisateur

Gima

Gima Glass Body Fat Analyzer Manuel de la liste des pièces

Seca

Seca 374 Manuel utilisateur

TEC

TEC TEC SL59 SERIES Manuel utilisateur

Axis

Axis B/E Series Manuel utilisateur

Alecto

Alecto ACW-40 Manuel utilisateur

Rice Lake

Rice Lake MSI-4260 IS Manuel utilisateur

IKA

IKA RCT basic safety control Manuel utilisateur

ADE

ADE M20011 Manuel utilisateur

Duronic

Duronic KS3000 Manuel utilisateur

Digi

Digi SM-720 Manuel utilisateur

Cardinal

Cardinal CS Series Manuel utilisateur

Korona

Korona Kastella Manuel utilisateur

A&D

A&D FC-50Ki Manuel utilisateur

BDA

BDA CAMARGUE Manuel utilisateur

Tanita

Tanita HD-357 Manuel utilisateur

Leifheit

Leifheit 03173 Manuel utilisateur

Lumme

Lumme LU-1340 Manuel utilisateur