ActiveProducts ZE03 Manuel utilisateur
ZE03_04/2007_REV.1
PLEASE KEEP THE ORIGINAL BOX, PACKAGING AND RECEIPT.
WARRANTY REGISTRATION BY INTERNET, WWW.ACTIVEPRODUCTS.COM.
www.activeproducts.com / 1-866-924-7626
QUESTIONS, PROBLEMS, MISSING PARTS?
Before returning to your retailer, visit our website or call our customer service at
PURCHASE DATE: _______________ SERIAL#: ___________________________________
CAUTION !
BEFORE OPERATING THIS UNIT, PLEASE READ THIS MANUAL THOROUGHLY
AND RETAIN IT FOR FUTURE REFERENCE.
IF YOU MUST STORE YOUR PRESSURE WASHER IN A PLACE WHERE TEMPERATURE IS
BELOW 41ºF (5ºC), YOU MUST APPLY WINTERIZING PROCEDURE TO PROTECT IT. FAILURE
TO WINTERIZE THE UNIT MAY PERMANENTLY DAMAGE PUMP AND VOID THE WARRANTY.
SEE PAGE 10 FOR WINTERIZING PROCEDURE.
EVERYDAY PRESSURE WASHER
ITEM: 39-8603-8
MODEL NO.: ZE03
TM
Max. pressure: 1650PSI
Water flow rate: 1.25GPM
Power source requirement: 120V, 60HZ
Electrical cord: 23’
High-pressure hose: 17’
Rated current: 11A
Water supply: COLD TAP WATER
Specifications
TECHNICAL SPECIFICATIONS
Technical specifications
Precautions
Safety Features and Electrical Power Information
Replacement Parts and Diagram
Assembly and Operating Instructions
Using the Accessories
Working with Detergent
Shut Down and Clean-up
Taking a Break
Winterizing and Long-term Storage
Maintaining Your Pressure Washer
Troubleshooting
Warranty
i
1
2
3
4
7
8
9
9
10
11
12
14
TABLE OF CONTENTS
i
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Save these instructions
In a double-insulation product, two systems
of insulation are provided instead of
grounding. No grounding means is provided
on a double-insulated product, nor should a
means for grounding be added to the
product. Servicing a double-insulated
product requires extreme care and
knowledge of the system, and should be
done only by qualified service personnel.
Replacement parts of a double-insulated
product must be identical to the parts they
replace. A double-insulated product is
marked with the words “DOUBLE INSULA-
TION” or “DOUBLE INSULATED”. The
symbol “ ” may also be marked on the
product.
Servicing of a double-insulation product:
When using this product, basic precautions
should always be followed:
•
Read all the instructions before using the
product.
•
Water spray must never be directed
towards any electric wiring, devices or
directly towards the pressure washer
machine itself or fatal electric shock may
occur.
•
To reduce the risk of injury, do not operate
the machine near children.
•
Learn how to stop the machine and release
pressure quickly. Be thoroughly familiar
with the controls.
•
Stay alert—watch what you are doing.
•
For use with cold water supply only. Do not
draw other liquids.
•
The pressure washer should not be used in
areas where gas vapours may be present.
An electric spark could cause an explosion
or fire.
•
To minimize the amount of water getting
into the pressure washer, the unit should
be placed as far as possible from the
cleaning site during operation.
•
Avoid accidental starts. Shut power “OFF”
before connecting or disconnecting cord to
electrical outlets.
•
Do not operate the product when fatigued
or under the influence of alcohol or drugs.
•
Do not stand on unstable surfaces. Stand
with both feet balanced at all times.
•
Prior to starting the pressure washer in cold
weather, be sure ice has not formed in any
part of the equipment.
•
Never carry your pressure washer by the
cord. Do not pull on the cord to disconnect
from the outlet.
•
To allow free air circulation, the pressure
washer should not be covered during
operation.
• Keep operating area clear of all people.
• Follow the maintenance instructions
specified in the manual.
WARNING - Risk of Injection or Injury - Do Not
Direct Discharge Stream at Persons
•
High pressure jet can be dangerous if misused.
The jet must not be directed at persons, animals,
electrical devices, or the unit itself.
WARNING - Risk of Explosion - Do not spray
flammable liquids
• Do not use acids and solvents in this product.
These products can cause physical injuries to the
operator and irreversible damage to the machine.
CAUTION - Gun Kicks Back - Hold with both
hands
• The trigger gun safety lock prevents the trigger
from accidentally being engaged. The safety
feature DOES NOT lock trigger in the ON
position.
WARNING - Risk of Electrocution
• Inspect cord before using - Do not use if cord is
damaged.
• Keep all connections dry and off the ground.
• Do not touch plug with wet hands.
• Do not use extension cord with the product.
Safety Warnings
•
Before servicing, cleaning or removal of any
parts, shut “OFF” power and relieve pressure.
•
Do not spray electrical apparatus and wiring.
If connection is made to a portable water
system, the system shall be protected against
backflow.
Warnings
•
Do not use with flammable liquids and toxic
chemicals.
•
Injection Hazard: Equipment can cause
serious injury if the spray penetrates the skin.
•
Do not point the gun at anyone or any part of
the body. In case of penetration seek medical
aid immediately.
•
This system is capable of producing 1650PSI.
To avoid rupture and injury, do not operate
this pump with components rated less than
1650PSI working pressure (including but not
limited to spray guns, hose and hose
connections).
IMPORTANT SAFETY INSTRUCTIONS - READ FIRST!
1
WARNING: Do not spray electrical apparatus
and wiring.
WARNING: When a combustible liquid is sprayed
there may be danger of fire or explosion
especially in a closed area. Read instruction
manual before operating.
WARNING: Arcing parts. Keep the
compressor/motor at least 6 meters away from
explosive vapours.
Extension cords are not recommended unless
they are plugged into a ground fault
circuit-interrupter found in circuit boxes or
protected receptacles.
Warning
The pressure washer is also equipped with a
main power “ON/OFF” switch located on the
unit. It should always be moved to the “OFF”
position when the pressure washer is not
being used to prevent possible injury or
damage.
Warning
The pressure washer is equipped with a stop
device that will sense when the trigger on the gun
is released. It will open the power circuit to the motor
and cause the pressure washer motor to stop. Motor
will resume again when trigger is pulled.
Extension Cords
If possible, do not use extension cords with this
product. However, if you must use one, observe all
the warnings and instructions listed below:
Use a sufficient gauge:
Maximum cable length: 50’ = 14 AWG
Use only extension cords that are intended for
outdoor use. These extension cords are identified
by a marking “Acceptable for use with outdoor
appliances; store indoors while not in use.”
Use only extension cords having an electrical rating
not less than the rating of the product.
Do not use damaged extension cords. Examine
extension cord before using and replace if
damaged. Do not abuse extension cord and do not
yank on any cord to disconnect.
Keep cord away from heat and sharp edges.
Always disconnect the extension cord from the
receptacle before disconnecting the product from
the extension cord.
To reduce the risk of electrocution, keep all connec-
tions dry and off the ground. Do not touch plug with
wet hands.
•
•
•
•
•
•
SAFETY FEATURES AND ELECTRICAL POWER INFORMATION
2
ZE01-090-0003
ZE03-000-0002
ZE03-000-0001
ZE01-090-0004
ZE03-090-0001
ZE01-000-0003
ZE03-090-0002
ZE03-090-0005
Adjustable Wand
Gun Holder
Cable & Hose Hook
Main Unit
Turbo Wand
Water Filter
High - Pressure Hose
Detergent Bottle & Wand
Gun Assembly
1
1
1
1
1
1
1
1
1
5
4
3
2
6
10
8
7
1
ZE01-050-0000
Quick Coupling & Inlet Adapter
111
Parts No.
Part NameItem no. Quantity
Parts List
REPLACEMENT PARTS AND DIAGRAM
3
1
2
3
11
10
8
7
6
5
4
I/ON
O / OFF
Make sure that the ON/OFF switch is in the
“OFF” position.
Separate the adaptor and quick-connect
coupling. Attach inlet adaptor to the machine’s
inlet and attach the quick-connect coupling
onto the garden hose.
Insert the wand into spray gun, and twist 1/4 turn until rectangular tab appears.
Step 1 Step 2
Step 3
Do not draw non-water liquids through the unit. For
use with cold water supply only.
Water hose must be at least a 1/2” in diameter.
Flow rate of water supply must not fall below 2 GPM
(gallons per minute).
Flow rate can be determined by running the water
for one minute into an empty 5-gallon container.
The water supply temperature must not exceed
104°F (40°C).
Water Supply (Cold Water Only)
•
•
•
•
•
Caution
To prolong the life of the unit, it is
recommended to rest the unit 5 minutes
after every 30 minutes of use.
Caution
•
•
•
Never use the pressure washer to draw in
water contaminated with solvents (e.g.
paint thinners, gasoline, oil, etc.).
Dirt in the feed water will damage the unit.
To avoid this risk, we recommend
checking the water filter (located inside
the water inlet; to clean it out see
Maintenance section on page 11).
Always prevent debris from being drawn
into the unit by using a clean water
source and an accessory water filter if
required.
Surface Preparation
Before starting any cleaning task, it is important to inspect the area for objects which could create a
hazard. Remove from the workarea which could be tripped over, such as toys or outdoor furniture.
Ensure that all doors and windows are closed tight.
Assembly Time: 2 minutes / Tools Required: None
ASSEMBLY AND OPERATING INSTRUCTIONS
4
Fig.6
Fig. 5
Attach the high-pressure hose to the water outlet. Twist tightly to avoid leakage.
Attach garden hose to water supply and turn
water on.
Plug the unit into an outlet.
Step 4
Step 5 Step 6
ASSEMBLY AND OPERATING INSTRUCTIONS – continued
5
Fig.7
Start the pressure washer by turning ON/OFF switch to ON.
Before turning the unit ON, depress the trigger to bleed any trapped air out of the pump and
hose.
Step 7
Step 8
ASSEMBLY AND OPERATING INSTRUCTIONS – continued
6
I/ON
O / OFF O / OFF
I/ON
Fig. 9
Adjusting The Spray
The adjustable spray nozzle can be adjusted
from fan to jet. The spray is adjusted from jet
to fan spray by turning the nozzle as shown
in Fig. 9.
Caution
To prolong the life of the unit, it is
recommended to rest the unit 5 minutes
after every 30 minutes of use.
Caution
Jet spray adjustment is very aggressive. Do
not adjust while spraying. We recommend
that for most cleaning applications a 20º
spray angle should be used to avoid
damage to the surface being sprayed.
USING THE ACCESSORIES
7
Warning
Never use bleach, chlorine products
and other corrosive chemicals.
Never use liquids containing solvents
(i.e., paint thinners, gasoline, oils).
Never use ammonia products.
Never use acid-based products.
These products can cause physical
injuries to the operator and irreversible
damage to the machine and/or
damage the surface being cleaned.
Caution
Make sure the gun safety lock is engaged
so the trigger cannot be squeezed while
the detergent nozzle is being attached.
Step 1
Fill the detergent container with detergent
only. Do not put any water into container.
Step 2
Step 3
Attach the detergent wand onto the gun as
shown. Make sure all components are locked.
Step 4
Release the gun safety lock and pull the trigger
to operate the unit and apply the detergent.
Do not allow the detergent to dry on the
surface that you are cleaning.
Working with detergent ensures a quick soaking
of the dirt, and allows the high-pressure water
to penetrate and remove the dirt more effectively.
Always spray detergent on a dry surface, do not
pre-soak area. Wetting the surface first dilutes
the detergent andreduces its cleaning ability
Using the detergent
WORKING WITH DETERGENTS
8
Fig.10
Fig.10
Table des matières
Autres manuels ActiveProducts Nettoyeur haute pression
ActiveProducts
ActiveProducts XE03 Manuel utilisateur
ActiveProducts
ActiveProducts YE03 Manuel utilisateur
ActiveProducts
ActiveProducts 1450 Manuel utilisateur
ActiveProducts
ActiveProducts ZE02 Manuel utilisateur
ActiveProducts
ActiveProducts PW0501400 Manuel utilisateur
ActiveProducts
ActiveProducts XE06 Manuel utilisateur
