ACTAtek HT-2200 Manuel utilisateur

Page 1 of 5

ACTAtek PTE LTD

ACTAtek HT-2200

The Lithium Ion Polymer Rechargeable Battery

DC 12 V 1100mAh

ACTAtek

LINUX WEB-BASED, BIOMETRIC &RFID SMART CARD SYSTEMS ACCESS CONTROL, TIME ATTENDANCE &PAYROLL SOLUTIONS

This manual contains important safety instructions that should be followed during

operation of the battery. Please read this manual thoroughly before using this battery.

Instruction Manual

Page 2 of 5

IMPORTANT SAFETY INSTRUCTIONS

READ ALL SAFETY AND OPERATION INSTRUCTIONS BEFORE OPERATING THE BATTERY.ADHERE

TO ALL WARNINGS,FOLLOW ALL OPERATING AND USER INSTRUCTIONS.

WARNING

zDisconnect from load before cleaning. Do not use liquid or aerosol cleaners.

zDo not expose the battery to liquid or moisture or humidity.

zDo not expose the battery to extremely high or low temperatures.

zDisposal of battery in a fire may cause explosion.

zDo not short-circuit the battery. Do not let the metal contacts on the battery

touch another metal object.

zDo not drop, throw the battery. It may explode if damaged.

zDisassembling or dismantling the battery will release electrolytes which are

toxic in nature and harmful for skin and eyes.

zThere are no user-serviceable parts inside. For service, please contact

ACTAtek Pte Limited.

CAUTION

zThe battery can be charged and discharged hundreds of times, but it will

eventually wear out.

zFor best results, charge the battery for 4 hours before the first use.

zThe battery should only be charged in temperatures between +5°C (+41°F) and

+45°C (+113°F)

zUsing chargers other than the given one might be dangerous for battery.

zUnplug the charger from the power socket and battery when not in use.

zDo not leave a fully charged battery connected to the charger, since

overcharging may shorten its lifetime. If left unused, a fully charged battery

will lose its charge over time.

zUse the battery for the intended purpose only.

zDo not use any damaged battery or charger.

zIf the battery is not been used, recharge it every 3 months to ensure its lifetime.

DISPOSAL

zDispose the battery according to local regulations.

zDo not dispose battery or charger as household waste.

zUse a battery disposal facility, if available.

DISCLAIMER

While every effort has been made to ensure that the information in this manual is accurate and

completed, ACTAtek Pte Limited expressly disclaims any liability for errors or omissions in

such information and materials.

ACTAtek Pte Limited accepts no responsibility, and disclaims all liability for damages resulting

from use of this information or for any errors or omissions.

Page 3 of 5

MAIN SPECIFICATION

FRONT PANEL

INPUT &OUTPUT

Config Socket Charger Socket

DC 12V Output

REGULATORY AGENCY APPROVAL

Item Minimum Typical Maximum

Output Voltage (V) 11.7 12 12.3

Output Current (A) n/a n/a 1.4

Charging Voltage (V) 10 12 14

Charging Current (A) 1.0 1.1 1.2

Charging Time (Hour) n/a n/a 4

Back-up Interval (Minute) 1 n/a Always Up

Charge/Discharge Cycles 500 times n/a n/a

Battery Capacity Dimension Weight Operating Temp

1100 mAh 110x65x22 mm 145g –10°C to +60 °C

ACTAtek

Test

Charge

LED 5

LED 4

LED 3

LED 2

LED 1

Page 4 of 5

OPERATION

Safety feature

The battery has a safety feature that it automatically shuts down to protect from short-circuit or

overloading. Under this circumstance, the battery needs to be re-activated.

Press the test button to check charge level indicator (LED1 – 5)

1. If all indicators lights are off means the battery has shut down and requires to be

activated.

2. If some of indicators lights stay on means the battery is normal.

Steps to re-activate the battery

Connect the charger to an electrical outlet. Connect the battery to its charger, the charge level

and charge indicator will illuminate. Hold the recharging for at least 5 seconds. Disconnect it

from the charger. Press the test button again. The charge level indicator illuminates and the

battery is activated successfully.

Charging

Connect the charger to an electrical outlet and the charger cable to the socket on the battery. The

charger indicator LED displays red during charging. When the battery is fully charged, then all

LED indication lights will turn green.

Discharging

Connect the battery to ACTAtek; Press the test button to start the discharging, the battery will

start supplying power to ACTAtek. The discharging will stop automatically when the defined

discharge period is over. Please refer to the user guide of Battery

Configuration Tool.

When charge level goes less than 10%, the charge level LED 1

will blink until the battery automatically shuts down from energy

exhaustion or disconnect from ACTAtek.

Page 5 of 5

Charge Level

Press the test button to check the battery charge level if it is not being charged. The appropriate

charge level indicator LED will illuminate for 5 seconds as shown below.

SERVICE

1, Contact ACTAtek Customer Service through:

•http://support.hectrix.com

•Service Hotline: +852 2153 1131

Note the model number of the battery, the serial number, and the date purchased, before you

call ACTAtek Customer Service. A technician will ask you to describe the problem and try to

solve it over the phone. If the problem persists, the technician will issue a RMA number. You

can return the defective battery to ACTAtek Pte Limited.

2, If the Battery is under warranty, repairs are free. If not, there is a repair charge.

3, Pack the battery properly and carefully to avoid damage in transit. Damage sustained in

transit is not covered under warranty. Mark the RMA number on the outside of the package.

LIMITED WARRANTY

ACTAtek Pte Limited warrants its products to be free from defects in materials and workmanship for a

period of six months from the date of purchase. Its obligation under this warranty is limited to repairing

or replacing, at its own sole option, any such defective products. To obtain service under warranty you

must obtain a RMA number from customer support. Products must be returned with transportation

charges prepaid and must be accompanied by a brief description of the problem encountered and proof of

date and place of purchase. This warranty does not apply to equipment that has been damaged by

accident, negligence, or misapplication or has been altered or modified in any way. This warranty applies

only to the original purchaser who must have properly registered the product within 10 days of purchase.

10% - 20% 20% - 30%

30% - 40%

40% - 60% 60% - 80%

Table des matières

Manuels Accessoires pour appareils photo populaires d'autres marques

Viltrox

Viltrox EF-NEX Instructions d'installation

Calumet

Calumet 7100 Series CK7114 Manuel utilisateur

Ropox

Ropox 4Single Series Manuel utilisateur

Cambo

Cambo Wide DS Digital Series Mode d'emploi

Samsung

Samsung SHG-120 Manuel utilisateur

Ryobi

Ryobi BPL-1820 Manuel d'utilisation

Aegis

Aegis ABL-36020P Manuel utilisateur

Pentax

Pentax Data Back Fc Manuel utilisateur

Fantasea

Fantasea EyeGrabber F Series Manuel utilisateur

Honeywell

Honeywell HDZ20HD Manuel utilisateur

EGO

EGO BA1400T Manuel utilisateur

Sima

Sima SRW-62 Manuel utilisateur

Shape

Shape A7SSMKIT Manuel utilisateur

Slide Kamera

Slide Kamera HST-2 Manuel utilisateur

Power works

Power works 2902613 Manuel utilisateur

SES

SES SE-2047-2 Manuel utilisateur

Olympus

Olympus PT-EP05L Manuel utilisateur

Starlite

Starlite OctoDome nxt Manuel utilisateur