ACR STOVES MV2CL Manuel utilisateur

TECHNICAL MANUAL

Malvern

Multifuel Stove

Model MV2CL

To be retained by the user for future reference

Serial Number ……………………………. Document MV2CL 0101

Version 1 Date 29/06/15

Thank you for purchasing an ACR Heat Products stove.

Important

To ensure that you gain the most from your purchase, please take a few

minutes to read through this manual before lighting the appliance for the

first time.

SINCE APRIL 2002 ONLY REGISTERED COMPETENT INSTALLERS CAN INSTALL

SOLID FUEL APPLIANCES. INSTALLATIONS CARRIED OUT BY NON-REGISTERED

INSTALLERS MUST BE INSPECTED BY LOCAL AUTHORITY BUILDING CONTROL.

FOR MORE INFORMATION PLEASE CONTACT HETAS AT www.hetas.co.uk OR

TELEPHONE 0845 6345626

The installation of this appliance must comply with current Building

Regulations and local regulations, including those referring to

national and European standards need to be complied with when

installing the appliance.

Do not operate this appliance if it becomes damaged.

Improper use, maintenance or fitting parts other than those

approved by the manufacturer could lead to the appliance

becoming damaged or unsafe which in turn could lead to personal

injury or damage to the property and will void the warranty.

The appliance must not be modified in anyway unless authorized by

ACR Heat Products Ltd.

The appliance should be inspected regularly to ensure the airways

are clean and free from obstruction and the chimney swept at least

once a year.

The external surfaces of this appliance will be very hot to the touch

when in operation and due care will need to be taken when

operating the appliance to ensure safety. A fire guard should be

fitted if it is likely that the elderly, infirm or children may come into

contact with the appliance.

This appliance must not be used as an incinerator.

This appliance has been designed for intermittent operation.

Before installation, please ensure that the correct model has been supplied.

Please also make a note of the serial number of your appliance in the

space provided on the front cover of this manual as this will be requested if

you require technical assistance in the future.

MALVERN SPECIFICATIONS

Nominal heat output ………… 5 kW –WOOD 4.8 kW –SMOKELESS FUEL

Chimney draft required ……… 12Pa

Height …………………………… 535 mm

Width ……………………………. 445 mm

Depth ………………………….... 285 mm

Weight …………………………… 80 kg

Air Requirement ……………….. N/A ***

Flue Mass Gas Flow …………… 4.3g/s –WOOD 7.1g/s –SMOKELESS FUEL

Mean Flue Gas Temperature... 273°C –WOOD 273°C - SMOKELESS FUEL

Efficiency ………………………... 78.3% - WOOD 70.8% - SMOKELESS FUEL

Log Length ………………………. Up To 350 mm

*** Please note that Building Regulations Document J advises that

additional permanent air supply is required for appliances with an output of

above 5Kw.

With modern properties additional air may be required as Document J

suggests that adequate air would be a benefit.

If design air permeability ≥5.0m³/ (h.m²) then 550mm²/kW of appliance

rated output above 5kW

If design air permeability ≤5.0m³/ (h.m²) then 550mm²/kW of appliance

rated output

If in doubt, please consult your registered installer for advice.

NOTE: DO NOT INSTALL IN A ROOM CONTAINING AN EXTRACTOR FAN

MV2CL Dimensions

The Clean Air Act 1993 and Smoke Control Areas

Under the Clean Air Act local authorities may declare the whole or part of

the district of the authority to be a smoke control area. It is an offence to

emit smoke from a chimney of a building, from a furnace or from any fixed

boiler if located in a designated smoke control area. It is also an offence to

acquire an "unauthorized fuel" for use within a smoke control area unless it is

used in an "exempt" appliance ("exempted" from the controls which

generally apply in the smoke control area).

The Secretary of State for Environment, Food and Rural Affairs has powers

under the Act to authorize smokeless fuels or exempt appliances for use in

smoke control areas in England. In Scotland and Wales this power rests with

Ministers in the devolved administrations for those countries. Separate

legislation, the Clean Air (Northern Ireland) Order 1981, applies in Northern

Ireland. Therefore it is a requirement that fuels burnt or obtained for use in

smoke control areas have been "authorized" in Regulations and that

appliances used to burn solid fuel in those areas (other than "authorized"

fuels) have been exempted by an Order made and signed by the

Secretary of State or Minister in the devolved administrations.

The Malvern Classic (MV2CL) has been recommended as suitable for use in

smoke control areas when burning wood.

When the primary air control is in the closed position, it remains

permanently open by 5mm and is prevented from closing fully by a screw.

Further information on the requirements of the Clean Air Act can be found

here: http://smokecontrol.defra.gov.uk/

Your local authority is responsible for implementing the Clean Air Act 1993

including designation and supervision of smoke control areas and you can

contact them for details of Clean Air Act requirements

Installation Instructions

CO Alarms

It is required by building regulations that whenever a new or replacement

wood/solid fuel or biomass appliance is installed in a dwelling a carbon

monoxide alarm to BS EN 50292:2002 must be fitted in the same room as the

appliance.

The alarm should be install according to the alarms manufacturers

instructions and should not be considered a substitute for the appliance

being installed incorrectly or regular maintenance of the appliance or flue

system.

Location of the unit

Clearances to non-combustible materials

There must be a minimum clearance of 150mm at each side of the

appliance. A clearance of 150mm is required at the back of stove (if the

rear wall has a thickness of 200mm or more this measurement can be

reduced to 50mm) a minimum clearance of 300mm is required above the

appliance.

Clearances to combustible materials

There must be a minimum clearance of 450mm at each side and 750mm at

the rear of the appliance from any combustible materials. If using single

wall flue pipe, there must be a clearance of at least 3 times the diameter of

the flue pipe (e.g. 125mm diameter pipe = 375mm minimum clearance)

from any combustible materials e.g. wooden beam.

Curtains and soft furnishings should be a minimum of 1m away from the

appliance.

Adequate space should be provided for servicing the appliance.

We do not recommend that plasma televisions and expensive artwork are

hung over the fireplace.

Please remember that this appliance has been designed to provide heat

and if installed into a recess enough space should be left around the

appliance to enable the heat produced to rise and escape from the recess

back into the room.

Hearth Requirements

The appliance must stand on a level fireproof hearth with a minimum

thickness of 12mm. The hearth temperature created by this stove is below

100˚C. The hearth must protrude at least 300mm in front of the appliance

and 150mm either side of the appliance.

The appliance shall be installed on a floor with an adequate load bearing

capacity. If an existing construction doesn’t meet with prerequisite, suitable

measures (e.g. load distributing plate) shall be taken to achieve it.

Flue Requirements

The chimney must comply with current Building Regulations. Provision must

be made to provide access for cleaning the appliance, the flue gas

connector and the chimney flue.

The flue must be:

In sound condition and provide sufficient draft

Suitable for use with solid fuel burning appliances

Be able to clean the entire length of the flue system without removal of

the appliance

Free from deposits

Well insulated

At least 4.5m in height

The flue must not be:

Shared with other appliances

Weight bearing on the appliance

A smaller diameter than the appliance flue collar size (125mm)

Assembly of the unit

This appliance is equipped with a manufactures smoke exempt stop

Pre –fitted, under no circumstances should it be tampered with or removed

unless expressly authorized by a competent person

The appliance is supplied pre-assembled with the flue spigot in the top exit

position.

If you intend to install the appliance using a rear flue connection, the

blanking plate should be swapped over as follows:

Remove the internal baffle plate.

Remove the rear blanking plate.

Remove the flue spigot from the top exit by removing the securing bolts

and rope seal.

Refit the rope seal and flue spigot to the rear exit and secure with the

bolts.

Refit the blanking plate to the top exit using the rope seal and retaining

bolts.

Maintenance

The chimney should be swept at least once a year together with the flue

pipe connection. Care should be taken to ensure that there is not a build

up of soot on the baffle and in the airways of the appliance.

If the appliance has not been operated for long periods, the flue should be

inspected and swept before use to ensure there are no blockages within

the flue.

The grate should be cleaned regularly and the ashpan emptied daily.

NEVER ALLOW THE ASH IN THE ASHPAN TO OVERFILL ALLOWING ASH TO BE IN

CONTACT WITH THE UNDERSIDE OF THE GRATE. This will overheat the grate

and cause premature wear and distortion.

The internal vermiculite panels of the appliance should be checked

regularly for soundness. If any wear and tear is found, we recommend

these parts are replaced immediately.

Check the rope door seals are intact and are not worn. These should be

replaced on an annual basis to ensure the correct operation of this

appliance.

The glass can be cleaned using a soft damp cloth or ACR Glassbright

ceramic glass cleaner (available from your local ACR Stove stockist)

Use only replacement parts recommended by the manufacturer.

We recommend that the appliance is serviced annually by a competent

engineer to ensure its continued safe operation.

User Instructions

Please note that during the first firing, we recommend a small fire is lit and

that you slowly increase the temperature to enable the various parts to

expand normally.

You may also experience fumes and a haze being given off by the stove

during the first firing and possibly for the next couple of firings as the paint

cures. This is normal but please ensure that the room is well ventilated

during this period.

The appliance should not be operated in mild weather with smokeless fuel.

Under certain weather circumstances e.g. fog the chimney will not draw

sufficiently and could cause asphyxiation. Either await better weather or

burn wood only.

In the rare event of a malfunction due to overheating or a chimney fire, the

air slides should be shut down completely and the fuel allowed to burn out.

In the event of a chimney fire, once the air slides have been closed

completely, dial 999 for assistance. If the appliance has overheated, the

appliance will need to be inspected for any damage before it can be

operated again.

Recommended Fuels

Wood –hardwood such as ash, oak and beech which have been cut for at

least 2 years and stored under shelter. The logs should have a maximum

moisture content of 20%. Maximum log length 350mm, maximum width

125mm.

Smokeless Fuels –such as Anthracite, Phurnacite, Ancit

Prohibited Fuels

Green wood –i.e wood which is less than 2 years old with a moisture

content of above 20%

Recovered wood –i.e pallets, railway sleepers etc. These will have been

chemically treated and will pollute the atmosphere and possibly overheat

the appliance.

Housecoal or Bituminous coal –these fuels will soot up the airways of the

stove and possibly overheat the appliance.

Petroleum Based Coke –this will overheat the appliance and possibly

damage the unit.

Liquid fuels.

Table des matières

Autres manuels ACR STOVES Poêle

ACR STOVES

ACR STOVES Birchdale FB4MF Manuel utilisateur

ACR STOVES

ACR STOVES Malvern Electric Manuel utilisateur

ACR STOVES

ACR STOVES Earlswood III Manuel utilisateur

ACR STOVES

ACR STOVES NOVUS Manuel utilisateur

ACR STOVES

ACR STOVES Langdale Manuel utilisateur

ACR STOVES

ACR STOVES NEO Electric Guide de l'utilisateur

ACR STOVES

ACR STOVES Ashdale FB2MF Manuel utilisateur

ACR STOVES

ACR STOVES Solis SOLMF Manuel utilisateur

ACR STOVES

ACR STOVES Oakdale FB1MF Manuel utilisateur

ACR STOVES

ACR STOVES Tenbury T400ECO Manuel utilisateur

ACR STOVES

ACR STOVES Buxton II Manuel utilisateur

Manuels Poêle populaires d'autres marques

Arada

Arada Cassette Stove Manuel utilisateur

Parmco

Parmco FS 600 Manuel utilisateur

MCZ

MCZ SUITE AIR 10 M2 Manuel utilisateur

HearthStone

HearthStone Stowe DV 8321 Guide de dépannage

Cattara

Cattara FAMILY Manuel utilisateur

Stanley

Stanley Argon F500 OVAL Manuel utilisateur

Avalon

Avalon B-VENT Manuel utilisateur

Nordpeis

Nordpeis Vega Manuel utilisateur

Exquisit

Exquisit EKC601-5 Manuel d'utilisation

Stanley

Stanley Oisin Oil MK II Manuel du propriétaire

Thermocet

Thermocet Brookfield S/CC Manuel utilisateur

HASE

HASE delhi Manuel utilisateur

Vermont Castings

Vermont Castings Intrepid 2 Manuel utilisateur

Italiana Camini

Italiana Camini CLASSICA Guide de démarrage rapide

Avalon

Avalon Vashon Avanti DVS FS Manuel utilisateur

Spartherm

Spartherm ambiente a1 Manuel utilisateur

Dimplex

Dimplex MCFSTV12AU Manuel utilisateur

Warmlite

Warmlite WL46040 Manuel utilisateur