Acnodes FPC 5084 Manuel utilisateur

FPC 5084

All-in-One

8.4” SVGA TFT Fanless Touch Panel

Computer with Intel

Atom

N270

Processor Onboard

User’s Manual

Disclaimers

This manual has been carefully checked and believed to contain

accurate information. Acnodes Corporation assumes no responsibility

for any infringements of patents or any third party’s rights, and any

liability arising from such use.

ACNODES does not warrant or assume any legal liability or

responsibility for the accuracy, completeness or usefulness of any

information in this document. ACNODES does not make any

commitment to update the information in this manual.

ACNODES reserves the right to change or revise this document

and/or product at any time without notice.

No part of this document may be reproduced, stored in a retrieval

system, or transmitted, in any form or by any means, electronic,

mechanical, photocopying, recording, or otherwise, without the prior

written permission of ACNODES Co., Ltd.

CorporationAll Rights

Reserved

July 2009, Version A1

Printed in Taiwan

iii

Safety Approvals

 CE Marking

 FCC Class A



FCC Compliance

This equipment has been tested in compliance with the limits for a

Class A digital device, pursuant to Part 15 of the FCC Rules. These

limits are meant to provide reasonable protection against harmful

interference in a residential installation. If not installed and used in

accordance with proper instructions, this equipment might generate or

radiate radio frequency energy and cause harmful interference to

radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment

does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the

following methods:

1. Reorient or relocate the receiving antenna.

2. Increase the separation between the equipment and receiver.

3. Connect the equipment to another outlet of a circuit that

doesn’t connect with the receiver.

4. Consult the dealer or an experienced radio/TV technician for

help.

Shielded interface cables must be used in order to comply with the

emission limits.

Safety Precautions

Before getting started, please read the following important safety

precautions.

1. The

FPC 5084

does not come equipped with an operating

system. An operating system must be loaded first before

installing any software into the computer.

2. Be sure to ground yourself to prevent static charge when

installing the internal components. Use a grounding wrist

strap and place all electronic components in any static-

shielded devices. Most electronic components are sensitive

to static electrical charge.

3. Disconnect the power cord from the

FPC 5084

before any

installation. Be sure both the system and external devices

are turned OFF. A sudden surge of power could ruin

sensitive components that the

FPC 5084

must be properly

grounded.

4. The brightness of the flat panel display will be getting weaker

as a result of frequent usage. However, the operating period

varies depending on the application environment.

5. Turn OFF the system power before cleaning. Clean the

system using a cloth only. Do not spray any liquid cleaner

directly onto the screen. The

FPC 5084

may come with or

w/o a touch screen. Although the touch screen is chemical

resistant, it is recommended that you spray the liquid cleaner

on a cloth first before wiping the screen. In case your system

comes without the touch screen, you must follow the same

procedure and not spray any cleaner on the flat panel

directly.

6. Avoid using sharp objects to operate the touch screen.

Scratches on the touch screen may cause malfunction or

internal failure to the touch screen.

7. The flat panel display is not susceptible to shock or vibration.

When assembling the

FPC 5084

, make sure it is

securely installed.

8. Do not open the system’s back cover. If opening the cover

for maintenance is a must, only a trained technician is

allowed to do so. Integrated circuits on computer boards are

sensitive to static electricity. To avoid damaging chips from

electrostatic discharge, observe the following precautions:

Before handling a board or integrated circuit, touch an

unpainted portion of the system unit chassis for a few

seconds. This will help to discharge any static

electricity on your body.

When handling boards and components, wear a wrist-

grounding strap, available from most electronic

component stores.

Trademarks Acknowledgments

ACNODES is a trademark of ACNODES Co., Ltd.

IBM, PC/AT, PS/2, VGA are trademarks of International

Business Machines Corporation.

Intel

and Atom

™

are registered trademarks of Intel Corporation.

MS-DOS, Microsoft C and Quick BASIC are trademarks of Microsoft

Corporation.

VIA is a trademark of VIA Technologies, Inc.

SST is a trademark of Silicon Storage Technology, Inc.

UMC is a trademark of United Microelectronics Corporation.

Other brand names and trademarks are the properties and registered

brands of their respective owners.

Table of Contents

Disclaimers

..........................................................................ii

Safety

Approvals................................................................. iii

Safety

Precautions..............................................................iv

CHAPTER 1 INTRODUCTION .......................................

1.1 General Description ............................................

1.2

Specifications...................................................... 2

1.2.1 Main CPU Board ......................................................... 2

1.2.2 I/O System .................................................................. 3

1.2.3 System Specification .................................................. 3

1.3 Dimensions .........................................................

1.4 I/O

Outlets........................................................... 7

1.5 Packing List ........................................................

CHAPTER 2 HARDWARE INSTALLATION .................. 9

2.1 CF card Installation.............................................

2.2 Serial Ports Interface ........................................

2.3 Ethernet ............................................................

2.4 Mountings – Panel/Wall/Desktop/VESA ...........

2.4.1 Panel Mounting ......................................................... 14

2.4.2 Wall-Mounting ........................................................... 15

2.4.3 Desktop-Mounting..................................................... 16

2.4.4 VESA-ARM Mounting ............................................... 18

2.5 DRAM Installation .............................................

2.6 Wireless LAN Card Installation .........................

CHAPTER 3 AMI BIOS SETUP UTILITY ..................... 25

3.1 Starting

............................................................. 25

3.2 Navigation

Keys

................................................

3.3 Main

........................................................

3.4 Advanced

................................................

3.5 PCI PnP

..................................................

3.6 Boot Menu ........................................................

3.7 Security

...................................................

3.8 Chipset Menu....................................................

3.9 Exit

..........................................................

vii

CHAPTER 4 DRIVERS INSTALLATION...................... 58

4.1

System

.............................................................. 58

4.2 Touch Screen ...................................................

4.2.1 Specification.............................................................. 59

4.2.2 Driver Installation- Windows XP ............................... 59

4.3 Embedded O.S. ................................................

4.3.1 Windows XP Embedded ........................................... 62

4.3.2 Windows CE.NET 6.0 ............................................... 63

viii

MEMO

Introduction

FPC 5084 User Manual

CHAPTER 1

INTRODUCTION

This chapter contains general information and detailed specifications

of the

FPC 5084

. Chapter 1 includes the following sections:



General Description



Specification



Dimensions



I/O Outlets



Package List

1.1 General Description

The FPC 5084 is a fan-less and compact-size touch panel computer,

equipped with a 8.4” TFT LCD display and low power consumption

Intel

○

Atom

N270 1.6GHz processor with FSB

533MHz. The FPC 5084 supports Windows

XP, Windows

CE.NET and Windows

XP embedded. The panel computer is able to

install a CompactFlash

™

card and provide a Mini card socket for

wireless module. Its excellent ID and friendly user interface make it a

professional yet easy-to-use panel computer. The FPC 5084 is an

ideal for space-limited applications in factory automation, machine

maker operating systems, building automation, and more.

FPC 5084: 8.4” TFT SVGA Fanless Touch Panel

Computer



Reliable and Stable Design

The FPC 5084 adopts a fanless cooling system and a

FPC 5084

Introduction

CompactFlash

™

card, which makes it suitable for vibration

environments.



Embedded O.S. Supported

The FPC 5084 not only supports Windows

XP, but also

supports embedded OS, such as Windows

CE.NET, and

Windows

XP embedded. For storage device, the FPC 5084

830 supports CompactFlash

™

card.



Industrial-grade Product Design

The FPC 5084 has an incredible design to be used in different

industrial environments.

The front bezel meets the IP65/NEMA4 standard.

For connecting other devices, the FPC 5084 also features

several interfaces: USB, Ethernet, and RS-232/422/485.

1.2 Specifications

1.2.1 Main CPU Board



CPU



Intel

○

Atom

N270 1.6GHz processor with FSB 533MHz

onboard



System Chipset



945GSE + ICH7M



BIOS



America Megatrends BIOS



System Memory



One 200-pin DDR2 SO-DIMM socket



Maximum memory up to 2GB

Table des matières

Autres manuels Acnodes Écran tactile

Acnodes

Acnodes PC 5171 Manuel utilisateur

Acnodes

Acnodes FPC 7161 Manuel utilisateur

Acnodes

Acnodes PC 2150 Manuel utilisateur

Acnodes

Acnodes FPC 8121 Manuel utilisateur

Acnodes

Acnodes PC 8150 Manuel utilisateur

Acnodes

Acnodes PC 8175 Manuel utilisateur

Acnodes

Acnodes PC8719 Manuel utilisateur

Acnodes

Acnodes PC 5152 Manuel utilisateur

Acnodes

Acnodes PC 5171 Manuel utilisateur

Acnodes

Acnodes PC 8170 Manuel utilisateur

Acnodes

Acnodes PC 2150 Manuel utilisateur

Acnodes

Acnodes PC 8120 Manuel utilisateur

Acnodes

Acnodes PC 1150 Manuel utilisateur

Acnodes

Acnodes PC 5170 Manuel utilisateur

Acnodes

Acnodes FPC 6150 Manuel utilisateur

Acnodes

Acnodes FPC 8150 Manuel utilisateur

Acnodes

Acnodes 17" TFT Expandable Intel Core 2 Duo Industrial Panel PC with 2 PCI PC... Manuel utilisateur

Acnodes

Acnodes PC 8175 Manuel utilisateur

Acnodes

Acnodes PC 1150 Manuel utilisateur

Acnodes

Acnodes PC 8153 Manuel utilisateur

Acnodes

Acnodes FOX 9981 Manuel utilisateur

Acnodes

Acnodes PC 5171 Manuel utilisateur

Acnodes

Acnodes PCH3782 Manuel utilisateur

Acnodes

Acnodes PC 6150 Manuel utilisateur

Manuels Écran tactile populaires d'autres marques

FlowLine

FlowLine Data loop Manuel utilisateur

ALPEX

ALPEX AEx-8 P Series Manuel utilisateur

Ltech

Ltech E5S Manuel utilisateur

Harman

Harman AMX MODERO S MSD-701-L2 Manuel utilisateur

AIS

AIS IP10IA99 series Manuel utilisateur

IBASE Technology

IBASE Technology ASTUT-152-RE1S Manuel utilisateur

YASKAWA

YASKAWA TP 610C Manuel utilisateur

B&R

B&R Power Panel C Series Manuel utilisateur

Beijer Electronics

Beijer Electronics X2 control Manuel utilisateur

AXIOMTEK

AXIOMTEK GOT321W-521 Manuel utilisateur

TRIDONIC.ATCO

TRIDONIC.ATCO x-touchBOX Manuel utilisateur

Qomo

Qomo QIT1386 Manuel utilisateur

DFI

DFI KS104-CD Manuel utilisateur

AMX

AMX AXP-PPC Mode d’emploi

Sartorius

Sartorius X3 PR 5410 Manuel utilisateur

AMX

AMX Modero X Series Manuel utilisateur

Advantech

Advantech TPC-30 Series Manuel utilisateur

B&R Industries

B&R Industries MAPPC900-ENG Manuel utilisateur