ACME CW-108 Manuel utilisateur

Innovation, Quality, Performance

CW‐108



 UserManual

 Pleasereadthemanualcarefullybeforeusing

CONTENTS

1. Safety Instructions........................................................................................ 2

2. Technical Specifications................................................................................ 4

3. How to Set the Fixture ................................................................................. 5

3.1 Control Panel.......................................................................................... 5

3.2 Main Function ........................................................................................ 6

4. How to Control the Unit ............................................................................ 11

4.1 Master/Slave Built In Preprogrammed Function..................................... 11

4.2. Easy Controller (by CA-8) .................................................................... 12

4.3 DMX Controller .................................................................................... 12

5. DMX 512 Configurations............................................................................ 14

6. DMX 512 Connections............................................................................... 15

7. Troubleshooting ......................................................................................... 16

8. Fixture Cleaning ......................................................................................... 17

Declaration of Conformity

We declare that our products (lighting equipments) comply with the following

specification and bears CE mark in accordance with the provision of the

Electromagnetic Compatibility (EMC) Directive 89/336/EEC.

EN55103-1: 2009 ; EN55103-2: 2009; EN62471: 2008;

EN61000-3-2: 2006 + A1:2009 + A2:2009; EN61000-3-3: 2008.

Harmonized Standard

EN60598-2-17:1989 + A2:1991; EN60598-1:2008+ A11: 2009

EN 62471:2008; EN 62493: 2010

Safety of household and similar electrical appliances

Part 1: General requirements

17B

E. One of the channels is not working well

1. The stepper motor might be damaged or the cable connected to the PCB is broken.

2. The motor’s drive IC on the PCB might be out of condition

8. Fixture Cleaning

The cleaning of internal and external optical lenses and/or mirrors must be carried out

periodically to optimize light output. Cleaning frequency depends on the environment in

which the fixture operates: damp, smoky or particularly dirty surrounding can cause greater

accumulation of dirt on the unit’s optics.

yClean with soft cloth using normal glass cleaning fluid.

yAlways dry the parts carefully.

yClean the external optics at least every 20 days. Clean the internal optics at least every

30/60 days.

1. Safety Instructions

WARNING

yPlease keep this User Guide for future consultation. If you sell the unit to another user, be

sure that they also receive this instruction booklet.

yPlease unpack and check carefully there is no transportation damage before using the unit.

yBefore operating, ensure that the voltage and frequency of power supply match the power

requirements of the unit.

yIt’s important to ground the yellow/green conductor to earth in order to avoid electric

shock.

yThe unit is for indoor use only. Use only in a dry location.

yThe unit must be installed in a location with adequate ventilation, at least 50cm from

adjacent surfaces. Be sure that no ventilation slots are blocked.

yPlease disconnect main power before replacement or servicing.

yPlease make sure there are no flammable materials close to the unit while operating as it is

fire hazard.

yPlease use safety cable when fixes this unit. DO NOT handle the unit by taking its head only,

but always by taking its base.

yMaximum ambient temperature is Ta: 40℃. DO NOT operate it where the temperature is

higher than this.

yUnit surface temperature may reach up to 85℃. DO NOT touch the housing bare-hand

during its operation. Turn off the power and allow about 15 minutes for the unit to cool

down before replacing or serving.

Please read the instruction carefully, it includes important

information about the installation, usage and maintenance.

yIn the event of serious operating problem, stop using the unit immediately. Never try to

repair the unit by yourself. Repairs carried out by unskilled people can lead to damage or

malfunction. Please contact the nearest authorized technical assistance center. Always use

the same type spare parts.

yDO NOT touch any wire during operation as high voltage might be causing electric shock.

Warning:

yTo prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or

moisture.

yDO NOT open the unit within five minutes after switching off.

yThe housing, the lenses, or the ultraviolet filter must be replaced if they are visibly

damaged.

Caution:

There are no user serviceable parts inside the unit. DO NOT open the housing or attempt

any repairs yourself. In the unlikely event your unit may require service, please contact your

nearest dealer.

Installation:

The unit should be mounted via its screw holes on the bracket. Always ensure that the unit

is firmly fixed to avoid vibration and slipping while operating. And make sure that the

structure to which you are attaching the unit is secure and is able to support a weight of 10

times of the unit’s weight. Also always use a safety cable that can hold 12 times of the

weight of the unit when installing the fixture.

The equipment must be fixed by professionals. And it must be fixed at a place where is out

of the touch of people and has no one pass by or under it.

For 230V 50Hz power supply, maximum fixtures that can be connected on one power cable is 8;

For 120V 60Hz power supply, maximum fixtures that can be connected on one power cable is 4;

16B

3 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)

5 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+),

Pin 4/Pin 5: Not used.

7. Troubleshooting

Following are a few common problems that may occur during operation. Here are some

suggestions for easy troubleshooting:

A. The unit does not work, no light and the fan does not work

1. Check the connection of power and main fuse.

2. Measure the mains voltage on the main connector.

3. Check the power on LED.

B. Not responding to DMX controller

1. DMX LED should be on. If not, check DMX connectors, cables to see if link properly.

2. If the DMX LED is on and no response to the channel, check the address settings and

DMX polarity.

3. If you have intermittent DMX signal problems, check the pins on connectors or on PCB of

the unit or the previous one.

4. Try to use another DMX controller.

5. Check if the DMX cables run near or run alongside to high voltage cables that may cause

damage or interference to DMX interface circuit.

C. Some units don’t respond to the easy controller

1. You may have a break in the DMX cabling. Check the LED for the response of the master/

slave mode signal.

2. Wrong DMX address in the unit. Set the proper address.

D. No response to the sound

1. Make sure the unit does not receive DMX signal.

2. Check microphone to see if it is good by tapping the microphone

15B

6. DMX 512 Connections

1. If you using a controller with 5 pins DMX output, you need to use a 5 to 3 pin

adapter-cable.

2. At last unit, the DMX cable has to be terminated with a terminator. Solder a 120 ohm

1/4W resistor between pin 2(DMX-) and pin 3(DMX+) into a 3-pin XLR-plug and plug it in

the DMX-output of the last unit.

3. Connect the unit together in a `daisy chain` by XLR plug from the output of the unit to the

input of the next unit. The cable can not branched or split to a `Y` cable. DMX 512 is a

very high-speed signal. Inadequate or damaged cables, soldered joints or corroded

connectors can easily distort the signal and shut down the system.

4. The DMX output and input connectors are pass-through to maintain the DMX circuit,

when one of the units’ power is disconnected.

5. Each lighting unit needs to have an address set to receive the data sent by the controller.

The address number is between 0-511 (usually 0 & 1 are equal to 1).

6. The end of the DMX 512 system should be terminated to reduce signal errors.

7. 3 pin XLR connectors are more popular than 5 pin XLR.

2. Technical Specifications

◇Equipped with 36pcs of 3W R,G,B,W LEDs, creating powerful multi beam effect.

◇Three Operation Modes: DMX, Master/Slave, Sound Active.

◇DMX CH modes: 4/5/7CH selectable.

◇Beam Angle: 13.5°

◇Spectacular built-in programs under master/salve operation, triggered by music.

◇0-100% full range dimmer and variable strobe speed.

◇Optional easy controller CA-8 for instant lighting shows at your fingers.

◇Ideal for rental, clubs, bars, discos, parties, mobile DJs and more.

◇Input Voltage: AC 100V~240V, 50/60Hz

◇Power Consumption: 99W

◇Light Source: 36pcs×3WRGBWLEDs

(Red: 8pcs; Green: 10pcs; Blue: 10pcs; White: 8pcs)

◇Fuse: T6.3A

◇Dimension: 260 × 195 × 293mm

◇Weight: 4Kgs

3. How to Set the Fixture

3.1 Control Panel

1. Function Display: Show the various menus and the selected functions

Function Button:

2. MENU To select the programming functions

3. DOWN To go backward in the selected functions

4. UP To go forward in the selected functions

5. ENTER To confirm the selected functions

LED:

6. DMX On DMX input present

7. MASTER On Master Mode

8. SLAVE On Slave Mode

9. SOUND Flashing Sound activation

10. Microphone: Receive the Sound to control the fixture.

11. Power Input: Connect to supply mains power for the unit.

12. DMX Input: For DMX512 link, use 3-pin XLR plug cable to input the DMX single.

13. Power Output: Connect to supply mains power for the unit.

14B

5. DMX 512 Configurations

4/5/7 channels mode:

13B

Please refer to the following diagram to address your DMX512 channel for the first 4 units：

14.DMX Output: For DMX512 link, use 3-pin XLR plug cable to link the next unit.

15. Only for remote control: Connect with CA-8 to control the unit for Stand by, Function and

Mode function.

3.2 Main Function

To select any functions, press the MENU button until the required one is shown on the

display. Select the function by the ENTER button and the display will blink. Use the DOWN

and UP button to change the mode. Once the required mode has been selected, press the

ENTER button to setup or it will automatically return to the main functions without any

change after idling one minute. Back to the functions without any change press the MENU

button.

The main functions are shown below:

12B

control the others to give an automatic, sound activated, synchronized light show. This

function is good when you want an instant show. Any fixture can act as a Master or as a Slave.

2-light show

In slave mode, slave 1 means the unit works as master, slave 2 means 2-light show. In order

to create a great light show, you can set the second unit to slave 2 to get contrast movement

to each other, even if you have two units only.

4.2. Easy Controller (by CA-8)

The easy remote control is used only in master/slave mode. By connecting to

the 1/4” microphone jack of the first unit, you will find that the remote

controller on the first unit will control all the other units for Stand by, Function

and Mode selection

Blackout

To blackout all the fixture

Function

Strobe

1. Synchronous strobe

2. Two –light strobe

3. Sound strobe

Select Chase

Select color

Select Fade Speed

Fast

Middle

Slow

Mode Sound

(LED OFF)

Chase

(LED ON)

Color

(LED slow blinking)

Speed

(LED fast blinking)

4.3 DMX Controller

Use universal DMX controller to control the units, you have to set the DMX address from 1 to

512 channel so that the units can receive DMX signal.

Press the MENU button up to when the is showing on the display. Press the ENTER

button and the display will blink. Use the DOWN and UP button to change the DMX512

address. Once the address has been selected, press and keep the ENTER button pressed up to

when the display stops blinking or storing automatically one minute later. To go back to the

functions without any change press the MENU button again.

11B

Auto Test

Select the , press the ENTER button and the unit will run the built-in programmer for

self-test. To go back to the functions press the MENU button.

Fixture Temperature

Select the , press the ENTER button and the display will show the temperature of the

unit. To go back to the functions press the MENU button again.

Fixture use time

Select the , press the ENTER button and the display will show the number of working

hours of the unit. To go back to the functions press the MENU button.

Software version

Select the , press the ENTER button and the display will show the version of software of

the unit. To go back to the functions press the MENU button again.

4. How to Control the Unit

You can operate the unit in three ways:

1. By master/slave built-in preprogram function

2. By easy controller

3. By DMX controller

No need to turn the unit off when you change the DMX address, as new DMX address setting

will be affected at once. s.

4.1 Master/Slave Built In Preprogrammed Function

The fixture will allow you to link 2 fixtures together and operate without a controller. In

Master/Slave mode, the first fixture whose DMX input jack has with nothing connect will be

master automatically, set other units to slave 1 or slave 2 via menu, then the first unit will

DMX 512 Address

Select the , press the ENTER button and the display will blink. Use the DOWN and UP

button to change the DMX 512 address. Once the address has been selected, press the

ENTER button to setup or automatically exit menu mode without any change after one minute.

Back to the previous functions without any change press the MENU button.

Channel Mode

Select the , press the ENTER button and the display will blink. Use the DOWN and UP

button to select the (4 channels: Red, Green, Blue and White), (5 channels:

Red, Green, Blue, White and Dimmer) or (7 channels: Red, Green, Blue, White, Color,

Dimmer and Strobe) mode. Once the mode has been selected, press the ENTER button to

setup or automatically exit menu mode without any change after one minute. To go back to

the functions without any change press the MENU button.

Slave Mode

Select the , press the ENTER button and the display will blink. Use the DOWN and UP

button to select the (Master), (Slave 1) or (Slave 2) mode. Once the

mode has been selected, press the ENTER button to setup or automatically return to the main

functions without any change after one minute. To go back to the functions without any

change press the MENU button again.

Show Mode

Select the , press the ENTER button and the display will blink. Use the DOWN and UP

button to select the (Random show) or (color) or (fade).

When you selected the , press the ENTER button, and then use the DOWN and UP

button to select the (Color 1) … (Color 9), press the ENTER button and use

the DOWN and UP button to adjust the brightness intensity from (Dimmer 0) to

(Dimmer 255); select the (Color 10), press the ENTER button, and select the

(Red), (Green),… (Dimmer), pressing the ENTER button and adjust the

brightness intensity from to .

When you selected the (Fade mode), press the ENTER button, and then use the

DOWN and UP button to adjust the fade speed from (Speed 1, the slowest) to

(Speed 3: the fastest).

Once you have finished the settings, press the ENTER button to setup or automatically exit

menu mode without any change after one minute. To go back to the last function without any

change press the MENU button.

Sound Mode

Select the , press the ENTER button and the display will blink. Use the DOWN and UP

button to select the (Sound mode on) or (Sound mode off). Once select, press

the ENTER button to setup or automatically exit menu mode without any change after one

minute. To go back to the functions without any change press the MENU button

Sound Sense

Select the , press the ENTER button, use the DOWN and UP button to adjust sensitivity

level between (the lowest) and (most sensitive). Press the ENTER button to

setup or automatically exit menu mode without any change after one minute. To go back to

the functions without any change press the MENU button.

Blackout mode

Select the , press the ENTER button and use the DOWN and UP button to select the

(blackout) or (normal). Press the ENTER button to setup or automatically exit

menu mode without any change after one minute. To go back to the functions without any

change press the MENU button.

10B

LED display

Select the , press the ENTER button and the display will blink. Use the DOWN and UP

button to select (LED display always on) or ( LED display off 20 seconds after

exit menu) mode. Once select, press the ENTER button to setup or exit menu mode without

any change after one minute. Back to the functions without any change press the MENU

button again.

Display Inverse

Select the , press the ENTER button and the display will blink. Use the ENTER button to

change the display mode between (Display normal) and (Display Inversion,

good for installing in the ceilings). Press the ENTER button to setup. Back to the functions

without any change press the MENU button.

White Balance

Select the , press the ENTER button and the display will blink. Use DOWN and UP

button to select the (Red), (Green) or (Blue), press the ENTER button to

confirm, then use DOWN and UP button to adjust the value from to , press the

ENTER button to store, automatically return to the main functions without any change after

one minute.

Manual Test

Select the , press the ENTER button, and use the DOWN and UP button to select

(Red), (Green) or … or (strobe), press the ENTER button to confirm and use

the DOWN and UP button to adjust the value. Once select press the ENTER button to setup

or automatically exit menu mode without any change after one minute. To go back to the last

function without any change press the MENU button.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels ACME Matériel de DJ

ACME

ACME Genesis move 25R Manuel utilisateur

ACME

ACME O2 Oxygen Manuel utilisateur

ACME

ACME ASTRO LED-256D Manuel utilisateur

ACME

ACME Theatre LED Colour Flood Manuel utilisateur

ACME

ACME CHEETAH LED-GF50 Manuel utilisateur

ACME

ACME MP-400Z IP Manuel utilisateur

ACME

ACME CYC-200 FC Manuel utilisateur

ACME

ACME Festival LED-787 Manuel utilisateur

ACME

ACME LED-920D Manuel utilisateur

ACME

ACME XP-1200F Manuel utilisateur

ACME

ACME E-40D TC DXX Manuel utilisateur

ACME

ACME CP-56U Manuel utilisateur

ACME

ACME BP-40 QW S DXX Manuel utilisateur

ACME

ACME Dotline360 TB-1230 QW Manuel utilisateur

ACME

ACME E-200 MB MC Manuel utilisateur

ACME

ACME LED-MB50 Manuel utilisateur

ACME

ACME LED-BL8 Manuel utilisateur

ACME

ACME MH-640S-ELC Manuel utilisateur

ACME

ACME ARAS Manuel utilisateur

ACME

ACME LED-PAR 100 WW/CW Manuel utilisateur

ACME

ACME LS-608 RGB Manuel utilisateur

ACME

ACME LED-MS150 Manuel utilisateur

ACME

ACME Stage Panel 1080 Manuel utilisateur

ACME

ACME Color Fusion CF-805 Manuel utilisateur

Manuels Matériel de DJ populaires d'autres marques

ALPHA LITE

ALPHA LITE ALPHA 1500 Manuel du propriétaire

Chauvet

Chauvet OVATION E-930VW Manuel utilisateur

Zumtobel

Zumtobel APHRODITE Home Manuel utilisateur

Snow Masters

Snow Masters Zig Oscillator Manuel utilisateur

EuroLite

EuroLite 50530554 Manuel utilisateur

Beamz

Beamz BUV243 Manuel utilisateur

thomann

thomann Stairville DJ Lase 40-G MK-III Manuel utilisateur

Eagletone

Eagletone 6 Eyes Flower Manuel utilisateur

EuroLite

EuroLite FLD-1508 Manuel utilisateur

Technical Pro

Technical Pro LG8xSEA Manuel utilisateur

JB Systems

JB Systems Lounge Laser DMX Manuel utilisateur

Lightmaxx

Lightmaxx Vega Halo 90 Manuel utilisateur

Elation

Elation FUZE WASH Z350 Manuel utilisateur

Maverick

Maverick MK3 WASH Manuel utilisateur

Infinity

Infinity TF-260C7 Fresnel Manuel utilisateur

Chauvet

Chauvet EVE E-50Z Manuel utilisateur

Eliminator Lighting

Eliminator Lighting E 138 Manuel utilisateur

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Manuel utilisateur