Ackcio BEAM-DG Manuel utilisateur

Setting up Digital Node (BEAM-DG)

This page provides information on setting up a Digital Node to work with the offline Ackcio

Beam gateway.

Installation

The Nodes can be directly affixed to a flat surface using M6 screws. However, for more

sophisticated mounting scenarios, we recommend using the node bracket. The node bracket

can be used to easily mount the node on flat surfaces, on pipes using U-bolts or cable-ties, or

in other complicated settings.

If you are using the bracket, first fix the node device to the bracket using M6 screws and nuts

as shown below.

Use four screws and nuts to attach the node to the bracket

Connect the SMA antenna to the bulkhead. Once the mounting is complete, the node should

look as follows.

Node Setup

1.Connect the node antenna to the antenna bulkhead. 2. Connect the sensorwires to the node

while ensuring that the wires are plugged in correctly.

RS232 Port

PWR : Positive power input (e.g.+12V)

GND : Negative power input of sensor

TX : Transmit out (TX) output of sensor

RX : Receive input (RX) of sensor

SHLD : Shield wire of sensor

RS485 Port

PWR : Positive power input (e.g.+12V)

GND : Negative power input of sensor

SHLD: Shield wire of sensor

(a) Full Duplex Mode

A : A line of sensor chain

B : B line of sensor chain

(b) Half Duplex Mode

A+/Y : A+ line of sensor chain

B+/Y : B- line of sensor chain

SDI Port

PWR : Positive power input (e.g.+12V)

GND : Negative power input of sensor

SIG1 : SDI line of sensor chain

SIG2 : Switch type sensor output

SHLD: Shield wire of sensor

3. Switch off the Node and insert the battery while ensuring the polarity is followed correctly.

Configuring via the Ackcio Beam App

1.Download Ackcio Beam app at Google Playstore and connect to Gateway WiFi.

2. Plug in the USB end of the cable via an OTG adapter to your Android phone.

3. Important! Please make sure the Node is switch off before connecting to your Android

phone. 4. Plugin micro USB end to the Node.

5. Switch on the Node.

6. Open the Ackcio Beam app on the phone. On toggle button, "Cloud" option is for Ackcio

Online Live version. "Gateway" option is for Offline version. Please choose "Gateway" to

proceed with offline version. (Please note that you need to add the Node and create the

project first before you commission the node. Please refer to Gateway Setup for details.)

"Gateway" option to connect to Offline Gateway

(i) You will see the project which you have already created once you open your Ackcio app.

Click the button to download the project and go in to the project, you will see the project

details.

(ii) Press "Reset" button on the Node itself. Then click on “Setup Device” on the lower left

menu on Ackcio app, the app will show connected node information. If the connection is

unsuccessful, press "Reset" button on Node and connect again.

(iii) <Optional Step> If Wireless Mesh (Relay) function is to be deployed, click on "Wireless

Mesh" toggle button to enable. Once done, click on “Setup Sensor”, you can now configure

the sensor settings.

Table des matières

Autres manuels Ackcio Matériel réseau

Ackcio

Ackcio BEAM-AN-S1 Manuel utilisateur

Manuels Matériel réseau populaires d'autres marques

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manuel utilisateur

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manuel utilisateur

Yudor

Yudor YDS-16 Manuel utilisateur

D-Link

D-Link ShareCenter DNS-320L Manuel utilisateur

Samsung

Samsung ES1642dc Instructions d'utilisation

Honeywell Home

Honeywell Home LTEM-PV Instructions de montage

evertz

evertz 7700 Series Manuel utilisateur

D-Link

D-Link ShareCenter DNS-343 Manuel utilisateur

Asante

Asante AsanteBridge 1012 Manuel utilisateur

FireBrick

FireBrick FB2700 Manuel utilisateur

Audiovox Electronics

Audiovox Electronics ARWH2T Manuel utilisateur

ADC

ADC DSX-1 Manuel

NetComm

NetComm NF2 Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 5620 Manuel utilisateur

Dell EMC

Dell EMC XC6420 Series Manuel utilisateur

Lanner

Lanner NCA-1020A Manuel utilisateur

Allied Telesis

Allied Telesis AT-TN121-A Manuel utilisateur

Arista

Arista CCA-ETM-Q12 Manuel utilisateur