Acer Altos EasyStore Manuel utilisateur

Altos easyStore Quick Installation Guide

1.1 Packing content:

One Altos easyStore with pre-installed Hard Disk Drives

One Power cord

One Software Installation CD

One DiskSafe Express Recovery CD

One RJ-45 Networking cable

1.2 Default Setting Name Default Setting

User name admin

Password storage

IP Address 192.168.0.101

Subnet Mask 255.255.255.0

DHCP Client Yes

1.3 Hardware Installation

In order to connect Altos easyStore, perform the following steps:

1. Carefully remove the Altos easyStore unit the package.

2. Connect an Ethernet cable from your computer directly to the back of the Altos easyStore in Figure

1-2.

3. Connect your host computer and Altos easyStore by RJ45 Networking cable in Figure 1-2.

4. Power on the Altos easyStore in Figure 1-1.

Figure 1-1: Front Panel

Figure 1-2: Rear Panel

Altos easyStore Quick Installation Guide

1.3 System Set-up

1. Insert the Installation CD into your CD-ROM drive. If the auto run application shown in Figure 1-3

opens when the CD is inserted, choose the options you want

Figure 1-3: Auto Run Application

2. To access the device, your computer will need to be configured to be on the same subnet as the

unit. The unit’s default IP address is 192.168.0.101 with a subnet mask of 255.255.255.0.

3. Open your web browser and type “http://192.168.0.101” in the address bar and press “ENTER”.

4. When you access Altos easyStore first time, system will display below interface for system

configuration. However, if your Altos easyStore comes with pre-installed and configured HDDs,

you can skip these steps.

Figure 1-4: System Initialization

Note: If you plug-in HDD in system but do not display at this page. Reinstall HDD then click SCAN to

search.

Altos easyStore Quick Installation Guide

5. Click “IE Browser” button and select latest firmware named “xxx.PKG” from the Software CD.

Then click “Open” and click “Upload” for uploading system firmware.

Figure 1-5: System firmware Figure 1-6: System firmware upload

6. System will start initialization. When system initialization is complete, please turn off browser

manually and wait for one minute.

Figure 1-7: System firmware upload Figure 1-8: System firmware upload complete

7. Open your web browser and type “http://192.168.0.101” in the address bar and press “ENTER”.

You will be taken to the “Welcome Page”, click “NEXT”

Figure 1-9: System Welcome Page

Altos easyStore Quick Installation Guide

8. The “License Agreement Page” appears, check “I accept the license agreement.” Then click “Next”.

Figure 1-10: End User Software License Agreement Page

9. The Host Name page appears. Click “Next” to accept the default name (NetworkStorage), or

enter a desired name for Altos easyStore. The Host name can be up to 15 characters long and

can include letters, numbers and hyphens.

Figure 1-11: System Host Name Page

Altos easyStore Quick Installation Guide

10. At the next step, configure your local “Date/Time”. When you are done with the setting, click

“Next”

Figure 1-12: Setup Date/Time Page

11. Setup “Network Setting”. Choose “Get an IP address automatically” (If you have DHCP server) or

use the default IP 192.168.0.101. When you are done with the setting, click “Next”

Figure 1-13: Network Settings Page

Altos easyStore Quick Installation Guide

12. Setup “Disk Configuration”. If you inserted more than one hard drive, you can select RAID 0 or

RAID 1. If you install over 3 HDDs, RAID 5 is enabled. When you are done with the setting, click

“Next”

Figure 1-14: Setup Disk Configuration

13. The storage will be divided into 2 portions: shared folders (default is 200MB) and backups, select

the desired volume for each one. When you are done, click “Finish”

Figure 1-15: Disk Space Distribution

Altos easyStore Quick Installation Guide

14. System will take a couple of minutes for RAID initialization depending on the HDD capacity and

type of RAID you chose.

Figure 1-16: System configuration started

15. After system configuration is complete, close browser manually and wait for several minutes.

16. Open your web browser and type “http://192.168.0.101” in the address bar and press “ENTER”.

Default setting of username and password is “admin” and “storage”

Figure 1-17: Logging into Altos easyStore Storage System

17. System initialization complete.

Altos easyStore Quick Installation Guide

Autres manuels pour Altos EasyStore

Table des matières

Autres manuels Acer Serveur de stockage réseau

Acer

Acer Aspire EASYSTORE H341 Manuel utilisateur

Acer

Acer Aspire EASYSTORE H341 Manuel utilisateur

Acer

Acer Aspire easyStore H340 Guide de configuration

Acer

Acer Altos EasyStore Manuel utilisateur

Acer

Acer Aspire easyStore H340 Guide de démarrage rapide

Acer

Acer Aspire easyStore H340 Manuel utilisateur

Acer

Acer Aspire easyStore H340 Manuel utilisateur

Acer

Acer AN1600 F1 Manuel utilisateur

Acer

Acer Aspire EasyStore Series Manuel utilisateur

Manuels Serveur de stockage réseau populaires d'autres marques

HP NetStorage 6000 Manuel utilisateur

Seagate

Seagate U10 ST320423A Manuel utilisateur

Synology

Synology RackStation RS816 Manuel

D-Link

D-Link ShareCenter Pro DNS-1200-05 Manuel utilisateur

Avid Technology

Avid Technology VideoRAID ST Guide de sécurité

Western Digital

Western Digital My Cloud Home Duo Manuel utilisateur

PrimeArray

PrimeArray 4xxx Manuel utilisateur

Buffalo

Buffalo TeraStation WSS WSH5010N6 Manuel utilisateur

Planex

Planex MZK-NAS01SG Manuel utilisateur

Intel

Intel SS4000-E - Entry Storage System NAS Server Manuel utilisateur

Synology

Synology RS2212+ Manuel utilisateur

Allnet

Allnet ALL69000 Manuel utilisateur

Adaptec

Adaptec 5325301580 Manuel utilisateur

Motorola

Motorola EXORdisk II Manuel utilisateur

Sony

Sony XDAAI1PK Manuel utilisateur

Cisco

Cisco Linksys NAS200 Instructions d'utilisation d'origine

Sans Digital

Sans Digital MR4UT6G Manuel utilisateur

AIC

AIC FB128-LX Manuel utilisateur