Access Lighting 20347 Manuel utilisateur

IMPORTANT

Before assembling your access lighting fixture, please make sure that

you carefully read through these instruction sheets. Consider having

your fixture installed by a qualified licensed electrician.

NOTE: The important safeguards and instructions that appear in this

manual are not meant to cover all possible conditions and situations

that may occur. It must be understood that common sense, caution and

care, are factors that can’t be built into any product. These factors must

be supplied by the person(s) caring for and operating the fixture.

STEP BY STEP INSTRUCTIONS

Before starting your installation disconnect the Power by turning off the

Circuit Breaker or by removing the fuse at the fuse box. Just turning the

light off at the light switch is not sufficient to prevent electrical shock.

MARK BACK PLATE LOCATION

Determine the desired location of your fixture. Hold

the back plate up to the surface and mark with a pencil

the location of the mounting plugs (small hole on

the up and down side of the back plate). Drill

a hole and insert the mounting plugs into the mounting

surface.

GENERAL INFORMATION

All electrical connections must be in accordance with all ordinances,

Local and National Electrical Codes. These fixtures are intended for

mounting to a standard 4” x 2 1/2”metal octagon outlet box. The box

must be directly supported by the building structure and U.L. Recognized.

WHAT YOU NEED

•

Screwdriver

•

Wire Cutters

•

Wiring Supplies as Specified

by Electrical Code

INSTALLATION INSTRUCTIONS

WHAT WE PROVIDE

•

Back Plate

•

Mounting Hardware

•

Gasket

•

1 x Crossbar

•

1 x Glass diffuser

•

1 x Front Cover

•

2 x 24W T5 HO Tubes

COLLECTION

CERTIFICATION: CETL WET NO. 20347

20347

APPLICATION MODEL NO.

Wall Fixture

CERTIFICATION: CETL WET NO. 20347

MOUNT CROSSBAR

If there is an existing fixture remove it.

Mount the crossbar with bracket to the J-box

with the supplied screws. Make sure that the additional

ADD THE GASKET

Fit the supplied Gasket onto behind the Back plate.

MAKE WIRE CONNECTIONS

Gently pull the supply wires through the hole in the

crossbar . Gently feed the fixture wire through one

of the slits in the back plate and then through the hole

floating canopy. Connect the black supply

wire to the black fixture wire. Secure with the supplied

wire nuts. Connect the white supply wires to the white

fixture wire. Secure with the supplied wire nuts. Either

wrap the green wire around one of the protruding screws

or connect it to the supply ground wire. Secure all wire

with electrical tape (not supplied).

Tuck all wires carefully into the J-Box.

CERTIFICATION: CETL WET NO. 20347

MOUNT THE BACK PLATE

Feed the nipple from the crossbar through the

designated hole in the back plate. Use the supplied

thumb nut to secure the nipple to the back plate. Hold

the back plate up to the mounting surface, insert the

supplied screws in the mounting plugs and secure the

back plate to the mounting surface.

INSERT TUBE

Insert the Tubes.

MAXIMUM WATTAGE 24W.

DO NOT EXCEED THE WATTAGE AS STATED

ON THE WARNING LABEL AND IN THE INSTRUCTION

SHEETS

SECURE THE GLASS DIFFUSER

Position the glass diffuser over the back plate.

Align the holes at the left and right of the plates.

Secure with the supplied allen screws and

L-type screw driver.

CERTIFICATION: CETL WET NO. 20347

SECURE THE FRONT COVER

Position the front cover over the glass diffuser.

Align the holes at the left and right of the plates.

Secure with the supplied screws.

Please ensure that the fitting is cool and

switched off before replacing the bulb.

DO NOT use bulbs that might exceed the

maximum wattage, stated on caution label.

CAUTION

RESTORE THE ELECTRICITY AND

CHECK THE OPERATION OF YOUR

NEW ACCESS FIXTURE

Autres manuels Access Lighting Luminaire

Access Lighting

Access Lighting 20368MG Instructions d'installation

Access Lighting

Access Lighting 50480 Instructions d'installation

Access Lighting

Access Lighting NIDO 63961LEDD Manuel utilisateur

Access Lighting

Access Lighting NITRO 2 62293 Manuel utilisateur

Access Lighting

Access Lighting SILO 20060LEDDMG Manuel utilisateur

Access Lighting

Access Lighting 62236 Instructions d'installation

Access Lighting

Access Lighting 20355 Instructions d'installation

Access Lighting

Access Lighting 31027 Instructions d'installation

Access Lighting

Access Lighting 30111 Manuel utilisateur

Access Lighting

Access Lighting ATOM 31000LEDSWACD Manuel utilisateur

Manuels Luminaire populaires d'autres marques

Emos

Emos CLASSIC ZY1431T Manuel utilisateur

Westinghouse

Westinghouse Outdoor Lighting Fixture Manuel utilisateur

Hedler

Hedler C 12 silent Manuel utilisateur

Blizzard Lighting

Blizzard Lighting Puck: CSI Manuel utilisateur

Energetic Lighting

Energetic Lighting ELYSL-5004 Series Manuel utilisateur

Lightmaxx

Lightmaxx Shaft 5R Manuel utilisateur

Triarch

Triarch 31083 Manuel utilisateur

Philips

Philips 32614 Series Manuel utilisateur

IKEA

IKEA TIVED Manuel utilisateur

Lightolier

Lightolier LP200 Manuel utilisateur

Chauvet Professional

Chauvet Professional ROGUE R1 BEAM WASH Manuel utilisateur

Martin

Martin MAC 250 Krypton Manuel utilisateur

Cooper Lighting

Cooper Lighting Halo L3232E Manuel utilisateur

Stageline

Stageline ODW-2410RGBW Manuel utilisateur

Light Sky

Light Sky Tornado Series Manuel utilisateur

Lightolier

Lightolier Paralyte 2424 PLA2G9LS26U Manuel utilisateur

Lightolier

Lightolier Lytespan 83ED17S Manuel utilisateur

Lightolier

Lightolier Calculite CS8226 Manuel utilisateur