Abtus ABT4659 Manuel utilisateur

| | | | e

ABT4659

Target Pole

Instruction Manual

| | | | e

1.0 Index

1.0 Index 1

2.0 Specification 1

3.0 Target Pole 1

4.0 Maintenance 3

4.1 Before Each Use 3

4.2 Every 3 Months 3

2.0 Specification

3.0 Target Pole

The target pole is an optional accessory for RouteScan. It allows the measurement of points that

cannot be ‘seen’ directly by the laser, such as the gauge corner of the rail on an adjacent track.

It is comprised of:

▪Target Pole;

▪Rail Pole;

▪Pointed Foot

▪Rounded Foot.

Weight

4kg

Size (stacked)

1585mm x 95mm x 45mm

| | | | e

To measure a point using the target pole, load the Single Point screen and tick the ‘Target Pole’ tick

box as shown in Figure 2. The software will automatically adjust the measurement by the vertical

height of the target.

Figure 1

Figure 2 AGI2 - Single Point Measurement

| | | | e

When measuring to the Target Pole:

•Ensure that the target surface is ‘square’ to the laser;

•Check that it is held vertically by using the bubble embedded in the top of the pole –a 1mm

offset of the bubble from the centre of the vial translates approximately to a 0.5mm error in the X-

Y measurement.

The Pointed Foot and Rounded Foot click into the bottom of the Target Pole and are interchangeable.

When using the Target Pole on its own, it is advisable to use the Rounded Foot to minimise wear to

the Pointed Foot (refer to Section 4.2).

When using the Target Pole with the Rail Pole, the Pointed Foot must be fitted. When measuring the

location of an adjacent track, the Rail Pole allows the Pointed Foot to be located accurately on the

gauge corner of the rail.

1. Place the Rail Pole on the track to be measured;

2. Ensure that the Rail Pole is located ‘squarely’ across the track and that it is firmly located

against the rail being measured;

3. Locate the Pointed Foot in the socket in the Rail Pole.

4.0 Maintenance

4.1 Before Each Use

Make sure there are no obstructions in the Rail Pole socket such as dirt.

4.2 Every 3 Months

Visually inspect the ABT4659 for signs of damage. If necessary, contact your local distributor for help.

Check the Pointed Foot and Rounded Foot for wear by measuring the length as shown in figure. The

foot should be replaced if it has worn by more than 1mm.

Figure 3

Table des matières

Autres manuels Abtus Instrument de mesure

Abtus

Abtus ABT 4610 Laser Offset Gauge Manuel utilisateur

Abtus

Abtus ABT4640 Manuel utilisateur

Abtus

Abtus ABT4650 RouteScan Manuel utilisateur

Abtus

Abtus ABT-7000 Manuel utilisateur

Abtus

Abtus ABT4650 RouteScan Manuel utilisateur

Abtus

Abtus IFP-600 Manuel utilisateur

Abtus

Abtus ABT 8000 Manuel utilisateur

Abtus

Abtus ABT-7100 Manuel utilisateur

Abtus

Abtus ABT5210 Ri59 Manuel utilisateur

Abtus

Abtus ABT5200 Manuel utilisateur

Abtus

Abtus ABT4050 Manuel utilisateur

Abtus

Abtus ABT 4550 Series Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur