ABSCO SHEDS CYC15 Guide d'installation

Absco Industries Assembly Instruction Manual Model: CYC15 02/03/2021 1.0 1

N3/C1 FRAME KIT

FOR 1.5m WIDE TO

1.5m DEEP MODELS

DOWNLOAD

OUR APP FOR

ASSEMBLY

VIDEOS

LEAVE A REVIEW

Tell us about your experience and

receive a $20 Coles Gift Card.

Visit www.abscosheds.com.au/review

AU: 1800 029 701

NZ: 0800 466 444

[email protected]

www.abscosheds.com.au

This kit is applicable to the following sheds:

The addition of this frame kit will increase the

wind rating of the speciﬁed sheds to

Wind rating: N3/C1 as per AS4055-2012.

Suitable for speciﬁc cyclonic regions

15151GK

15151SK

15141RK

WARNING: This shed must be anchored to a

100mm thick concrete slab with the concrete

anchors supplied.

Failure to do so will result in the shed not

having the structural integrity required to

endure a severe storms or cyclonic event.

WARNING: Doors must remain closed with

all padbolts properly secured during severe

storms or cyclonic event.

Where information conﬂicts with the original

non-cyclonic instruction manual, this

document is to be referenced.

View of frame kit

applied to

15151GK

Absco Industries Assembly Instruction Manual Model: CYC15 02/03/2021 1.0 2

N3/C1 FRAME KIT

FOR 1.5m WIDE TO

1.5m DEEP MODELS

GENERAL INSTRUCTIONS

• Before commencing any assembly, read through these instructions in detail to gain a thorough

understanding of assembly methods and associated details.

• Unpack the carton and carefully identify and check off all the parts against the parts described

and illustrated on "COMPONENTS PACKING LIST" pages.

• Local authority approval must be obtained prior to construction of the shed. Once you have

selected your site you will need to lodge a site plan to your local council.

• The bracing material supplied is 80 x 40 mm galvanised steel channel, similar to that used in steel

house framing. Some channels are required to be cut to speciﬁc lengths using a hacksaw.

SITE PREPARATION

• The site for the shed must be level. An uneven surface may result in misalignment of parts.

• The shed shall be erected on top of a reinforced concrete slab and anchored down appropriately.

• If using a rebated slab ensure that all frame uprights are trimmed 25mm.

TOOLS REQUIRED

SAFETY NOTES

• Some parts may have sharp edges. It is advisable to wear gloves when handling these items and

safety glasses if drilling holes. Sensible shoes are highly recommended.

• Do not erect your shed in windy conditions.

• It is highly recommended to erect the shed with two or more people.

RECOMMENDED

3mm drill bit

6mm drill bit

10mm drill bits

metal & masonry

Absco Industries Assembly Instruction Manual Model: CYC15 02/03/2021 1.0 3

N3/C1 FRAME KIT

FOR 1.5m WIDE TO

1.5m DEEP MODELS

COMPONENT PACKING LIST

FRAME PACK

QTY COMPONENT

DESCRIPTION

PART

No. CHK QTY COMPONENT

DESCRIPTION

PART

No. CHK

2FRONT

WALL C0660 2 DOOR

STUD S1785

2BACK

WALL C1460 2 DOOR STUD

EXTENSION C0400

4SIDE

WALL C1220 3 DOOR BRACE

HORIZONTAL K0640

2ROOF

BRACE C1470 2 DOOR BRACE

VERTICAL C1555

C Straight cut to both ends.

J20mm Tab notch on one end only

K20mm Tab notch on both ends

L45mm Lip notch on one end only

M45mm Lip notch on both ends

N20mm Tab notch + 45mm Lip notch

P20mm Tab notch + 45mm Lip notch on both ends

ROne end: 20mm Tab notch + 45mm Lip notch

SSPECIAL NOTCHING, not noted above.

FRAME SECTION IDENTIFICATION GUIDE

The ﬁrst letter of the part number is used to identify the notching

type. EG. K2940, see below for reference list.

The following digits represent the overall length of the item.

EG. K2940

Part K2940 is a channel that is 2940mm long with a 20mm Tab notch

at each end.

20mm Tab

notch

45mm Lip

notch

20mm Tab

notch

45mm Lip

notch

C S

Absco Industries Assembly Instruction Manual Model: CYC15 02/03/2021 1.0 4

N3/C1 FRAME KIT

FOR 1.5m WIDE TO

1.5m DEEP MODELS

COMPONENT PACKING LIST

FITTINGS AND ACCESSORIES

QTY COMPONENT

DESCRIPTION

PART

No. CHK QTY COMPONENT

DESCRIPTION

PART

No. CHK

1INSTRUCTION

MANUAL IM 1

8G x 3/8” SELF

TAPPING SCREW

(220 PACK)

FAST001

1HINGE

6 HOLE FAST012A 8

3/16” x 1/2”

PAN HD

BOLT

FAST002

3mm POP

RIVET PACK

(50 PACK)

FAST009 83/16”

NYLOC NUT FAST003

8MULTIPURPOSE

BRACKET (MPB) BKT17 1

10G x 5/8” WAFER

TEK SCREW

(300 PACK)

FAST014

DOOR

PLATE

2 CO + 2 ZINC

CO12A 4PADBOLT FAST006

4CORNER

BRACKET BKT10 2PADBOLT

HASP FAST007

M10 DYNABOLT

M10 NUT & BOLT

BRACKET (12 PACK)

ANCHOR

KIT 1PHILLIPS HEAD

DRIVER BIT FAST038

13MM DRILL

BIT DRILL 35 FAST033

HEX HD

TEK SCREW W/ NEO

WASHER 10-16x16mm

Absco Industries Assembly Instruction Manual Model: CYC15 02/03/2021 1.0 5

N3/C1 FRAME KIT

FOR 1.5m WIDE TO

1.5m DEEP MODELS

INSTALL EXTRA FASTENERS

Absco sheds sheets have punched holes typically spaced at 592mm from centre to centre.

To achieve a cyclonic wind rating additional screws will need to be installed to reduce these distances.

The fastener intended at these positions is FAST001, a 10mm self tapping screw.

Pre-drill and reinforce with extra screws at 148mm centres in the following locations

B- Roof panel to wall

C- Roof panel to ridge beam - inside [Not applicable to skillion models]

G- Wall sheet to wall channel - inside

Pre-drill and reinforce with extra screws at 296mm centres in the following locations

A- All sheet-to-sheet connections

D- Wall corners

E - Roof lip to sheet

F- Sheet to channel

15151GK shown for illustrative purposes.

Absco Industries Assembly Instruction Manual Model: CYC15 02/03/2021 1.0 6

N3/C1 FRAME KIT

FOR 1.5m WIDE TO

1.5m DEEP MODELS

INSTALL EXTRA FASTENERS - INTERIOR VIEW

means pre-drill 3mm hole

and ﬁx with FAST001

“G” - Wall sheet to top wall channel.

Pre-drill from inside the shed through the inside face of the top channel and into the wall sheet

at 148mm centres, (every pan) and then ﬁx with a screw. Do this on the front and back walls only.

Additional FAST001 for rear wallAdditional FAST001 for front wall.

“C” - Roof panel to ridge beam.

Pre-drill from inside the shed upward through the ridge beam and into the roof panel at 148mm

centres, (every pan) then ﬁx with a screw. Some screws will already be in these positions, skip these.

For illustrative purposes fasteners are shown on just one side of the

ridge beam.

Repeat again to other side.

Absco Industries Assembly Instruction Manual Model: CYC15 02/03/2021 1.0 7

N3/C1 FRAME KIT

FOR 1.5m WIDE TO

1.5m DEEP MODELS

BOXING FRAME SECTIONS

1. All frame sections have one side length of

38mm and another at 40mm.

3. Slide opposing sides together so that

each frame section ﬁts neatly inside the

other.

5. Fix with tek screws.

Use tek screws to ﬁx the two sections and complete a boxed frame member as shown. Make sure that

you alternate tek screw position on opposing sides of the boxed sections. Align tek screws 296mm

apart. This is approximately 2 sheet corrugations in distance. If spaced correctly the screw heads will

line up with corrugations of the sheets and will make for a ﬂush ﬁnish against the wall or roof.

2. Slide the 38mm side into the 40mm side

as shown.

4. Apply ﬁrm pressure to each side of the

boxed section to ﬁrmly lock it into position.

NOTE:

- Only the horizontal wall frame sections are to be boxed.

- Do not screw any boxed sections until they have been correctly sized as the speciﬁc step instructs.

- Roof section, door frames and upright door studs are singular pieces.

- Use self drilling tek screws for all assembly and installation of these sections.

Absco Industries Assembly Instruction Manual Model: CYC15 02/03/2021 1.0 8

N3/C1 FRAME KIT

FOR 1.5m WIDE TO

1.5m DEEP MODELS

USING SELF DRILLING TEK SCREWS

Self drilling tek screws are an effective means of securing components without the need to pre-drill

holes. By following these instructions you will be able to easily secure your frame kit components.

Self drilling tek screws require an electric or battery

drill for installation, Do not attempt to fasten tek

screws by hand.

If available make sure that the drill has the slow

speed and high torque settings selected.

Fit the supplied driver bit into the chuck of the drill.

Place the tek screw onto the tip of the driver and

place the tek screw into position using the weight

of the drill to prevent it from moving.

Once in position apply a moderate amount of

pressure to the drill

Start slowly, begin to drill the tek screw into the

metal.

Once the tek screw has stabilised while drilling

increase the speed until the tek screw threads ‘bite’

into the metal.

Absco Industries Assembly Instruction Manual Model: CYC15 02/03/2021 1.0 9

N3/C1 FRAME KIT

FOR 1.5m WIDE TO

1.5m DEEP MODELS

FRAMING OVERVIEW

Frame layout for:

15151GK

15151SK

15141RK*

*Not to scale

GENERAL NOTE:

- If shed is on a rebated slab S1785 will need to be cut-to-suit rebate height.

15141RK:

- Roof brace orientation will be perpendicular to what is shown.

- Roof braces will be trimmed to 2900mm.

15151SK:

- One central roof brace is required.

C0660

K0640

BKT17

C1555

C1470

S1785

C1220

C0400

BKT17

S1785

C1220

Horizontal wall

framing is boxed.

C0400C1460

BKT10

Absco Industries Assembly Instruction Manual Model: CYC15 02/03/2021 1.0 10

N3/C1 FRAME KIT

FOR 1.5m WIDE TO

1.5m DEEP MODELS

DOOR BRACING

2. Place door frame components on a ﬂat

and level surface and use one tek screw at

each join.

NOTE: If the door has been completely

assembled as per original instruction manual

you will need to remove the diagonal door

braces.

3. Make sure the frame is square and ﬁx with

a second tek screw at each join.

4. Turn frame over and repeat last step.

1. Seal any brace holes using the supplied

pop rivets, FAST007. Perform from the

outside of the door.

K0640

C1555

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels ABSCO SHEDS Entreposage extérieur

ABSCO SHEDS

ABSCO SHEDS Premier 23231GK Manuel utilisateur

ABSCO SHEDS

ABSCO SHEDS 30152SK-PTX Manuel utilisateur

ABSCO SHEDS

ABSCO SHEDS 30152GK Guide d'installation

ABSCO SHEDS

ABSCO SHEDS 23081SK-PTX Manuel utilisateur

ABSCO SHEDS

ABSCO SHEDS 30082SK-PTX Guide d'installation

ABSCO SHEDS

ABSCO SHEDS PREMIER 15151GK Manuel utilisateur

ABSCO SHEDS

ABSCO SHEDS PREMIER SHED Manuel utilisateur

ABSCO SHEDS

ABSCO SHEDS Space Saver 23081SK Manuel utilisateur

ABSCO SHEDS

ABSCO SHEDS 60303WK Manuel utilisateur

ABSCO SHEDS

ABSCO SHEDS 2308WBCK Manuel utilisateur

ABSCO SHEDS

ABSCO SHEDS CHICKEN COOP Manuel utilisateur

ABSCO SHEDS

ABSCO SHEDS PPCK-PTX Manuel utilisateur

ABSCO SHEDS

ABSCO SHEDS 3060HK Manuel utilisateur

ABSCO SHEDS

ABSCO SHEDS 23301GK Guide d'installation

ABSCO SHEDS

ABSCO SHEDS 30302GK Guide d'installation

ABSCO SHEDS

ABSCO SHEDS 15081SECOK Manuel utilisateur

ABSCO SHEDS

ABSCO SHEDS 1508WBCK Manuel utilisateur

ABSCO SHEDS

ABSCO SHEDS 30151SK Manuel utilisateur

ABSCO SHEDS

ABSCO SHEDS SIGNATURE ADCPSN3 Manuel utilisateur

ABSCO SHEDS

ABSCO SHEDS Regent 30142RK Manuel utilisateur

ABSCO SHEDS

ABSCO SHEDS PREMIER 30302GECOK Manuel utilisateur

ABSCO SHEDS

ABSCO SHEDS MN3060UTK Manuel utilisateur

ABSCO SHEDS

ABSCO SHEDS AWN33 Manuel utilisateur

ABSCO SHEDS

ABSCO SHEDS 3014F2 Manuel utilisateur

Manuels Entreposage extérieur populaires d'autres marques

USP

USP DURAMAX 10 Ft x 8 Ft StoreMax Plus Manuel utilisateur

TYGO

TYGO Nyland Manuel utilisateur

Duratuf

Duratuf GL105 Manuel utilisateur

Viking

Viking SD5300SS Manuel technique

USP

USP DURAMAX Apex Pro 10.5 Ft x 8 Ft 40116 Manuel utilisateur

ModuLaro

ModuLaro Lojo WC202200 Manuel utilisateur

Lifetime

Lifetime 6418 Manuel utilisateur

rollaway container

rollaway container ARPCA24 Manuel utilisateur

Duratuf

Duratuf Havelock Manuel utilisateur

X-METAL

X-METAL 4065 Manuel utilisateur

Outdoor Life Products

Outdoor Life Products FP2030 F Manuel utilisateur

Royalcraft

Royalcraft Faro 295L Storage Box Manuel utilisateur

Riverlea

Riverlea Duratuf KIWI KS3 Manuel utilisateur

OLT

OLT GS84D-FJ-Plywood Manuel utilisateur

Rubbermaid

Rubbermaid 5L45 Manuel utilisateur

garofalo

garofalo TUSCANY EVO Manuel utilisateur

Duratuf

Duratuf Kiwi MK1 Manuel utilisateur

Eden

Eden CA2988 Manuel utilisateur