Abocom SW800RE Manuel utilisateur

8-Port Fast Ethernet

10/100Mbps N-Way Switch

User’s Guide

FCC REGULATORY STATEMENTS

Part15, Class B

This device complies with Part 15 of FCC rules. Operation is

subject to the following two conditions:

1. This device may not cause harmful interface, and

2. This device must accept any interface received,

including interface that may cause undesired operation.

This equipment has been tested and found to comply

with the limits for a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful

interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy,

and if not installed and used in accordance with the

instructions, may cause harmful interference to radio

communications. However, there is no guarantee that

interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio

or television reception, which can be determined by

turning off and on, the user is encouraged to try to

correct the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the distance between the equipment and

receiver.

• Connect the equipment into an outlet on a circuit

different from that to which the receiver is connected.

Changes or modifications not expressly approved

by party responsible for compliance could void the

user authority to operate the equipment.

INTRODUCTION

The Fast Ethernet 10/100Mbps N-Way Switch

provides you a flexible, reliable, and affordable

solution of the Ethernet network. It comes with

eight independent 10BASE-T/100BASE-TX

ports. Each port delivers up to 200Mbps

throughput, and is able to operate in either half

or full-duplex modes.

The Fast Ethernet 10/100Mbps N-Way Switch

also processes a N-Way auto-negotiation

function, which automatically adjusts the device

for optimum operation; “Store-and-Forward”

architecture filters to eliminate error packets and

improve efficiency, and MDI/MDIX auto

crossover technology provides for detecting a

plugged straight through or crossover Ethernet

cable automatically. Plus, Built-in 2M bits

DRAM is smaller than the SRAM in dimension

and features very low power consumption, as

low as 1.8W.

Key Features & Specification

 Compliant with IEEE 802.3 10Base-T and IEEE

802.3u 100Base-TX standards

 Supports store-and-forward and cut-through

operation

 10/100Mbps port auto-detect on Full or Half

Duplex mode

 IEEE 802.3x or Back Pressure (HDX) Flow

- 1 -

Control

 Each Ethernet port supports MDI/MDIX

auto crossover capacity

 8 (Eight) 10/100Mbps Auto-Detection ports

 Provides non-blocking and non-head-of-line

blocking forwarding capacity

 Embedded 8K entries of look-up table and 128

entries of CAM

 2M bits DRAM is built in as package storage

buffer. Page based buffer management to

efficiently utilize the internal packet buffer.

 Broadcast storm control

 Power Feeding (Please do not use any other

adapters besides the one provided):

+5VDC/1.5A

 Dimension (WxDxH):

138.5mm x 76mm x 21.5mm

 Automatic power saving

 8 x RJ45 STP/UTP network ports on rear panel

 Emission Certification: FCC/CE Class B

 Operating Environment:

Temperature: 0 ~ 40oC; Humidity: 5 ~ 90 % RH

Package contents:

 One 8-Port 10/100Mbps Fast Ethernet N-Way

Switch

 One power adapter

 This User’s Guide

 Magnetic rubber feet

- 2 -

PARTS NAMES AND FUNCTIONS

Front Panel LED Indications

LED Status Description

POWER ON Power On

ON A valid connection

LINK/ACT Blinks Receives packets

ON Connects to a 100Mbps

Fast Ethernet connection

SPD

OFF Connects to a 10Mbps

Ethernet connection

Ethernet Ports (1-8)

Ethernet Ports with MDI/MDIX auto crossover

capacity.

Power Port

Connect to the External power adapter.

- 3 -

HARDWARE INSTALLATION

Hub installation

The hub is considered as a “plug and play”

network device and requires no special setup

except for plugging the appropriate power

adapter and cables.

1. Put the hub on the appropriate location.

When you install the hub, there are two

things needed to be considered:

Location: Your hub should be located in a

place that is central to your home/office

space and allows all computers and

networked devices connected to your hub.

Power: Remember to locate your hub near

electrical outlet.

2. Power on the hub by connecting the power

adapter.

3. Verify if the power (POWER) LED is on.

If the POWER LED does not light up,

check the power cord and power outlet to

verify its connection. If it still remains

unlit, please contact your dealer for support.

Ethernet Port Connection

Connect user machines, servers, another switch,

hub, or any other devices to the Ethernet ports on

this hub with either straight through or crossover

Ethernet cables.

- 4 -

Table des matières

Autres manuels Abocom Routeur réseau

Abocom

Abocom HomePlug 1.0 Turbo Ethernet Adapter PLE0085 Manuel utilisateur

Abocom

Abocom WR5205 Manuel utilisateur

Abocom

Abocom SW800AE Manuel utilisateur

Abocom

Abocom WR104 Manuel utilisateur

Abocom

Abocom UPA 200Mbps 802.11b/g AP/Router PLAR32 Manuel utilisateur

Abocom

Abocom WR5208 Manuel utilisateur

Abocom

Abocom VDSL to Ethernet Bridge VE1000 Manuel utilisateur

Abocom

Abocom WR5205G Manuel utilisateur

Abocom

Abocom PLC342 Manuel utilisateur

Abocom

Abocom WRN500 Manuel utilisateur

Abocom

Abocom PL1000 Manuel utilisateur

Abocom

Abocom ARM904 Manuel utilisateur

Abocom

Abocom WR5207 Manuel utilisateur

Abocom

Abocom WR5502 Manuel utilisateur

Abocom

Abocom MH200 Manuel utilisateur

Abocom

Abocom P3102-4g Manuel utilisateur

Abocom

Abocom CAS1040 Manuel utilisateur

Abocom

Abocom ARM804 Manuel utilisateur

Abocom

Abocom AR3500 Manuel utilisateur

Abocom

Abocom SW2400M Manuel utilisateur

Abocom

Abocom AR1000 Manuel utilisateur

Abocom

Abocom HomePlug AV Ethernet Bridge PLE0200 Instructions d'utilisation

Abocom

Abocom SW800 Manuel utilisateur

Abocom

Abocom SW500A Manuel utilisateur

Manuels Routeur réseau populaires d'autres marques

Allnet

Allnet ALL0333AU Manuel utilisateur

HomeSeer

HomeSeer HT-SEL Manuel utilisateur

Sercomm

Sercomm Genesis OC3505D Manuel utilisateur

Billion

Billion BIPAC 5102 Series Manuel utilisateur

TP-Link

TP-Link TD-8817 Manuel utilisateur

Motorola

Motorola MR1900 Manuel utilisateur

Digi

Digi IX14 Manuel utilisateur

Cisco

Cisco NCS 540 Manuel

XAVi

XAVi X8821e Manuel utilisateur

BEC

BEC 6200WZL Manuel utilisateur

MikroTik

MikroTik hAP ac3 Series Manuel utilisateur

Korenix

Korenix JetNet 5428G Series Manuel utilisateur

NETGEAR

NETGEAR FS526T - Switch Manuel utilisateur

Korenix

Korenix JetNet 5710G Series Manuel utilisateur

Automated Logic

Automated Logic ZN551 Manuel du propriétaire

Cisco

Cisco ASR 1000 Series Manuel de l'opérateur

EnGenius

EnGenius ESR-9710 Manuel utilisateur

Cisco

Cisco 805 Series Instructions d'utilisation et de sécurité