ABLE Kamstrup 382M Instructions d'installation et d'utilisation

Installation & Maintenance Instructions

Kamstrup 382M

Reading Oﬃce

Cutbush Park, Danehill, Lower Earley,

Reading, Berkshire. RG6 4UT. UK.

Tel: +44 (0)118 9311188

Email: [email protected]

Aberdeen Oﬃce

Unit 6 Airside Business Park, Kirkhill Industrial Estate,

Dyce, Aberdeen. AB21 0GT. UK.

Tel: +44 (0)1224 725999

Email: [email protected]

Internet: www.able.co.uk

e-procurement: www.247able.com

Registered in England No: 01851002

VAT No: GB 417 2481 61

255121131_B1_GB_10.2013

Installation manual

Connect the meter in accordance with the installation diagram on the meter’s type label.

Depending on the configuration a fixed value will be displayed, or the display will change

between selected indications every 10 seconds.

It is possible to change the display reading manually by activating the push button on the

meter. The available readings will depend on the meter’s configuration.

Security and installation guidelines

The meter is only to be used for measuring electrical energy and shall operate within the

specified values only.

The meter must be disconnected when working on it. It can be highly dangerous to touch the

meter parts when the meter is switched on.

Therefore, the relevant security fuse must be removed and kept in a place where it cannot be

inserted by unauthorized persons.

Current local standards, guidelines, regulations and instruction must be observed. Only

authorized personnel is permitted to install electricity meters.

Meters for direct connection must be protected against short circuit by a security fuse in

accordance with the maximum current stated on the meter.

LCD-display

Optical interface

LED (meter constant)

LED breaker status

(only meters with

internal breaker)

Push button

(not used)

Utility seals

Type label

Secondary module

Push button

The meter constant LED blinks proportionally to the consumed active energy.

Only authorized personnel must break the utility sealing.

55121131_B1_GB_10.2013

Installation manual

The phase indications have various functions. They indicate the two situations described below.

From the connection of the meter:

Indications L1, L2, L3 Indicate

On Voltage is above minimum limit (160V)

Off Voltage is below minimum limit (160V)

Indications Indicate

On The load is above the minimum (2.3W)

Off The load is below minimum limit (2.3W)

If the load exceeds the minimum limit and the meter is configured with this reading,

consumption will be indicated via the quadrant reading. The direction of the three phase

currents is indicated via the arrows above, respectively L1, L2 and L3.

7-digit identification field

Quadrant indicator

Module indication Text field

Unit field

Breaker symbol

Tamper symbol

Tariff indication

Radio network symbol

Error symbol

Phase sequence indication

9-digit value field

Phase current indication

Prepayment-symbol

Supply voltage indication

For future use

Terminals

Multi core 7 core Massive / terminals

35 mm2≥6 mm2≥6 mm2≥2.5 mm2

Screw: Pz 2 or straight slot

Torch: 2.5 – 3 Nm

Load control, installation

For meters with load control relay(s). Due to the delay in the meter, it is important to restart the

meter (off/on) when the time is set correctly in the meter. This places the relays in the correct

position and stops the delay timer.

455121131_B1_GB_10.2013

Installation manual

With built-in radio

If the meter is supplied with integral radio for establishment of remote reading, the meter

automatically connects to a radio network. The integral radio is equipped with an internal

antenna. The radio signal strength can be read by means of a hand-held terminal. If the

radio signal is not sufficient, an external antenna must be connected. Please see current

documentation on available antennas.

Mounting a communication module in the meter may influence on radio communication, please

contact Kamstrup.

With disconnection function

With this type of meter, it must be checked that the red diode is not switched on. This indicates

that the consumer’s supply is switched off.

Installation dimensions

171.7

269.2

80.3

Connection diagrams

The valid connection diagram appears from the type label.

12345678910 11 12

S0 +

P+

12345678910 11 12

S0 +

P+

Autres manuels ABLE Instrument de mesure

ABLE

ABLE VEGA VEGAFLEX 66 Instructions d'installation et d'utilisation

ABLE

ABLE BEKA associates BA648CF-F Instructions d'installation et d'utilisation

ABLE

ABLE Computrac Vapor Pro Rx Instructions d'installation et d'utilisation

ABLE

ABLE RHEONIK RHM NT Series Instructions d'installation et d'utilisation

ABLE

ABLE BEKA associates BA648CF-P Instructions d'installation et d'utilisation

ABLE

ABLE BEKA BA504E Instructions d'installation et d'utilisation

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur