ABB Slimline XRG00 Manuel utilisateur
—
I N S TA LL AT I O N I N S T R U C TI O N
Switch Disconnector Fuse
Slimline XRG00
—
Switch Disconnector Fuse
Slimline XRG00_rev.C/1SEQ100098P0001
—
Table of contents
01 Use of symbols
07
10 ITS
12 EFM
Motor operation
14 Fuse replacement
15 Accessory
04 Busbar overview
Manual operation
06
1
Hazardous voltage
Warns about a situation where a hazardous
voltage may cause physical injury to a per-
son or damage to equipment.
General warning
Warns about a situation where something
other than electrical equipment may cause
physical injury to a person or damage to
equipment.
—
Use of symbols
Caution
Provides important information or warns
about a situation that may have a detrimen-
tal effect on equipment.
Information
Provides important information about the
equipment.
SWI TCH DISCO NNEC TOR FUS E, X RG 0 0
Tools
Shows the needed tools for mounting or
fastening.
2
—
Receiving, handling and storage
Receiving and handling
Upon receipt, carefully inspect the switch
for damage that may have occurred during
transit. If damage is evident, or there is vis-
ible indication of rough handling, immedi-
ately file a damage claim with the transpor-
tation company, and notify your local ABB
sales office.
Do not remove the shipping package until
ready to install the switch.
Storage
If the unit will not be placed into service im-
mediately, store the switch on its original
package in a clean, dry location. To prevent
condensation, maintain a uniform tempera-
ture. Store the unit in a heated building, al-
lowing adequate air circulation and protec-
tion from dirt and moisture. Storing the
unit outdoors could cause harmful conden-
sation inside the switch enclosure.
HAZARD OF EQUIPMENT
OVERTURNING
When moving with a fork lift, do not re-
move the shipping package until the device
is in its final location.
Failure to follow this instruction will result
in personal injury or equipment damage.
Warning
SWI TCH DISCO NNEC TOR FUS E, X RG 0 0
3
—
Read these safety instructions
carefully before using this product!
HAZARD OF ELECTRIC SHOCK,
EXPLOSION, OR ARC FLASH
• Apply appropriate personal protective
equipment and follow safe electrical work
practices.
• This equipment must only be installed
and serviced by qualified electrical per-
sonnel.
• Before performing visual inspections,
tests, or maintenance on the equipment,
disconnect all sources of electric power.
Assume that all circuits are live unless
they are completely deenergized, tested,
grounded, and tagged. Pay particular at-
tention to the design of the power sys-
tem. Consider all sources of power, in-
cluding the possibility of backfeeding.
• Turn off switch before removing or mak-
ing load side connections.
• Always use a properly rated voltage sens-
ing device at all line and load to confirm
switch is off.
• Turn off power supplying switch before
doing any other work on or inside switch.
Failure to follow these instructions could
result in death or serious injury.
Danger
SWI TCH DISCO NNEC TOR FUS E, X RG 0 0
4
—
Busbar overview
SWI TCH DISCO NNEC TOR FUS E, X RG 0 0
A B C
D
F
E
A
B
C
D
E
F
50/5-2p
-
-
-
100
75
5
50/5-3p
50
50
-
-
75
5
50/5-4p
50
50
50
-
75
5
50/10-2p
-
-
-
100
75
10
50/10-3p
50
50
-
-
75
10
50/10-4p
50
50
50
-
75
10
—
Busbar overview
A
B
C
D
E
F
185/10-2p
-
-
-
370
77.5
10
185/10-3p
185
185
-
-
77.5
10
185/10-4p
185
185
97.5
-
77.5
10
AB
C
D
F
E
5
SWI TCH DISCO NNEC TOR FUS E, X RG 0 0
—
Manual operation
SWI TCH DISCO NNEC TOR FUS E, X RG 0 0
6
(4) 44(4)
3
Max. 4Nm
Max. 4Nm
45°
1
2
3
M6 thread forming screw (not included)
—
Motor operation
5
6 (6)
1
45°
2
4
7
SWI TCH DISCO NNEC TOR FUS E, X RG 0 0
3
3
Max. 4Nm
Max. 4Nm
45°
1
2
4
Pos. 3, 6 - M6 thread forming screw (not included)
Pos. 5 - M5X8 thread forming screw with a TX30 head (included)
Close
Open
2
1
—
Motor operation
SWI TCH DISCO NNEC TOR FUS E, X RG 0 0
8
Front cover must be locked
before operating
Signal: >0.5 sec or permanent
Manual operation: long hexagon bit size 3mm - approx. 40 revolutions
Table des matières
Autres manuels ABB Changer
ABB
ABB 3299E-A22100 Manuel utilisateur
ABB
ABB VD4 Series Guide rapide
ABB
ABB ITS2.1 Manuel utilisateur
ABB
ABB 3299-11500 Manuel utilisateur
ABB
ABB 6805U-508 Manuel utilisateur
ABB
ABB OTM C Series Manuel utilisateur
ABB
ABB OTM C 21D Manuel utilisateur
ABB
ABB DWTL1 Manuel utilisateur
ABB
ABB i-bus KNX 6108/02-500 Manuel de la liste des pièces
ABB
ABB 3299A-A02100 x Guide de configuration
ABB
ABB Zenith ZTS T Series Manuel utilisateur
ABB
ABB Ekip CI Manuel utilisateur
ABB
ABB DS1 Manuel utilisateur
ABB
ABB NE801 Manuel utilisateur
ABB
ABB ATS022 Manuel utilisateur
ABB
ABB ATS021 Manuel utilisateur
ABB
ABB vital 1 Manuel utilisateur
ABB
ABB Uniswitch Manuel utilisateur
ABB
ABB InLine II ZHBM-ITS Series Manuel utilisateur
ABB
ABB GE Entellysis Manuel utilisateur
