ABB AutoLink Manuel utilisateur

TEHI95094 - Rev.

Aut

oLink

15kV, 27kV, 38kV

Instruction Book



TEHI95094 –Rev. 2 2/ 12

Do not perform any of the activities described on this document with the Sectionalizer

energized.

All the activities listed on this document it must be performed with the Sectionalizer

completely de-energized and out of service.

ALWAYS follow your company Safety procedures before performing any work on this

equipment.

This product is intended to be operated and maintained by qualified persons, thoroughly

trained and knowledgeable of hazards involved. This document is written only for such qualified

persons and is not intended to be a substitute for adequate training and experience in safety

procedures for this device.

Detailed descriptions of procedures, safety principles and service operations are not

included on this document.

These warnings do not cover all conceivable ways in which service, whether or not

recommended by ABB, might be performed or the possible hazardous consequences of each

conceivable way, nor could ABB investigate such ways. Anyone using service procedures or

tools, whether or not recommended by ABB, must satisfy himself thoroughly that neither personal

safety nor equipment safety will be jeopardizedby the service method or tools selected.

For your safety!

Make sure that the installation area (spaces, divisions and ambient) is suitable for

electrical apparatus

Check that all the installation, putting into service and maintenance operations are

carried out by personnelwith suitable knowledge of the apparatus.

Make sure that the standard and legal prescriptions are complied with during

installation, putting into service and maintenance, so that installations according to the

rules of good working practice and safety in the workplace are constructed.

Strictly followthe information given in this document.

Checkthat the rated performance of the apparatus is not exceeded during service.

Check that the personnel operating the apparatus have this document at hand, as well

as all necessary information for correct intervention.

Pay special attention to the danger notes indicated in this document by the following

symbol:

Responsible behavior safeguards your own and other’s safety!

For any requests, please contact ABB.

The information and illustrations are not binding. We reserve the right to make changes

during technical development of the product.

TEHI95094 –Rev. 2 3/ 12

Table of Contents

1. Introduction.................................................................................................................................................... 4

2. Packing and Transportation........................................................................................................................ 4

3. Checking on Reception............................................................................................................................... 4

4. Storage .......................................................................................................................................................... 5

5. Description .................................................................................................................................................... 5

6. Installation..................................................................................................................................................... 5

6.1 General.................................................................................................................................................. 5

6.2 Installation and service conditions..................................................................................................... 5

6.3 Initial Setting or Previous Setting Modification Instructions........................................................... 6

6.4 Dip-Switch Configuration..................................................................................................................... 7

6.5 AutoLink Repositioning........................................................................................................................ 8

7. Commissioning........................................................................................................................................... 11

7.1 General procedures........................................................................................................................... 11

8. Maintenance................................................................................................................................................ 11

TEHI95094 –Rev. 2 4/ 12

1. Introduction

This document contains the required information to install medium voltage AutoLink

Sectionalizer and put it into service.

For a correct use of the product, please read it carefully.

Like every apparatus we manufacture, AutoLink is designed for specific applications.

Use only original spare parts.

For further information, please read the technical catalogue.

All installation, putting into service, commissioning and

maintenance operations must be carried out by suitably qualified

personnel with in-depth knowledge of the apparatus.

2. Packing and Transportation

The AutoLink Sectionalizer is shipped in cardboard package, in armed position.

3. Checking on Reception

Before carrying out any operation, always make sure that the

operating mechanism springs are charged and that the apparatus is in

armed position. When performing a reception test, it is required to

wait 5 minutes with the device de-energized after a tripping operation,

to reset it.

On reception, check the state of the apparatus, integrity of the packing and nameplate

information is the same requested on the purchase order specifications.

Make sure that all materials described in the shipping note are included in the supply.

If any damage or irregularity is seen in the supplied product after unboxing, notify ABB

(directly or through the agent or distributor) assoon as possible within five days of receipt.

The apparatus is only supplied with the accessories specified at the time of ordering and

validated in the order acknowledgement sent by ABB.

The documents sent in the shipping packing are:

- Test Certification

- Packing List

Other documents which are sent prior to shipment of the apparatus are:

- Order acknowledgement

- Original shipping advice notes

- Any drawings or documents referring to special configurations/conditions

TEHI95094 –Rev. 2 5/ 12

4. Storage

When the apparatus is unboxed, it must be carefully unpacked and checked as described

in Chapter 3 of this manual.

If immediate installation is not possible, the product should be kept in its original packing.

If immediate installation is not possible, store the equipment on its original packaging in a

covered, well-ventilated, dry, dust-free, non-corrosive ambient, away from any flammable

materials and at a temperature between -5°Cand +45°C.

In any case, avoid any accidental impacts or positioning which stresses the apparatus.

5. Description

The AutoLink Electronic Sectionalizer is a protection device that operates at a permanent

fault in the distribution line. It must be used together with a upstream recloser. Please take

note that the AutoLink is not a fuse tripping device, therefore it cannot be used as a

protection device by itself.

The AutoLink Electronic Sectionalizer is designed ONLY to protect

electrical equipment and NOT for saving people from accidents or

electrocution when contacting energized circuits.

6. Installation

6.1 General

Correct installation is very important. The manufacturer’s instructions

must be carefully studied and followed. It is good practice to use

gloves for handling the pieces during installation.

6.2 Installation and service conditions

The following standards must be taken into particular consideration during installation and

service:

- IEC 60694

- IEC 61936: Electrical Installation

- ANSI C37 63: Automatic Sectionalizer

- All accident prevention regulations in relative countries

For special installation requirements or other operating conditions, please contact ABB.

TEHI95094 –Rev. 2 6/ 12

6.3 Initial Setting or Previous Setting Modification Instructions

Remove the top cap (Fig. 1 A) using a 34mm fork spanner holding the tube with the hand

(Fig. 1 B). Check condition of O-ring (Fig. 2 E), and replace it if necessary, applying grease

on it.

Set the dip-switches to calibrate the current (Fig. 2 C, 4 switches) and set counting

operations (Fig. 2 D, 2 switches) using a small screwdriver according to table 1 settings.

Note: handle with care without damaging the switches. Settings must be made in a clean

and dry environment.

TEHI95094 –Rev. 2 7/ 12

6.4 Dip-Switch Configuration

Once the calibration current and counts are set, cover the dip-switch with silicon grease

(Fig. 3), supplied with AutoLink.

Check the condition of the O-Ring (Fig. 2 E) and apply silicon grease (Fig. 4 F) both inside

the cap and over the dip-switches.

TEHI95094 –Rev. 2 8/ 12

Place the cap, holding the tube with the hand, and tighten it using a 34 mm fork spanner

(torque between 8 and 10 Nm) without damaging the O-Ring (Fig. 5).

6.5 AutoLink Repositioning

Push the interlocking bolt (Fig. 6) until blocked (it will rotate freely). Do not strike the bolt,

nor use any type of tool to reset.

Turn the tensioning device support (Fig. 7).

Place the tensioning device support facing the interlocking bolt.

TEHI95094 –Rev. 2 9/ 12

Turn the tripping pin 90°, until the lower contact is firmly blocked (Fig. 8)

Place the pole in the tube inferioreyelet (Fig. 9)and position in the cutout-base.

TEHI95094 –Rev. 2 10/ 12

Withdraw the pole and place it in the tube’s superior eyelet (Fig. 10). Push it until it remains

in closing position.

Autres manuels pour AutoLink

Table des matières

Autres manuels ABB Dispositif de protection

ABB

ABB RELION REB670 Manuel utilisateur

ABB

ABB PCM600 Manuel utilisateur

ABB

ABB RET615 Manuel utilisateur

ABB

ABB ret650 Instructions d'utilisation

ABB

ABB REL 352 Manuel utilisateur

ABB

ABB Relion REG670 Guide de démarrage rapide

ABB

ABB REF601 Manuel utilisateur

ABB

ABB Relion 670 series Manuel utilisateur

ABB

ABB REM615 ANSI Manuel utilisateur

ABB

ABB Relion 615 series Instructions d'utilisation

ABB

ABB REF601 Instructions d'utilisation

ABB

ABB Relion 615 series Instructions d'utilisation

ABB

ABB RELION REL670 Manuel utilisateur

ABB

ABB Relion REQ650 Manuel utilisateur

ABB

ABB Relion 615 series Manuel utilisateur

ABB

ABB relion REF615 Manuel utilisateur

ABB

ABB ret650 Manuel utilisateur

ABB

ABB Relion 670 series Mode d’emploi

ABB

ABB Relion REQ650 Instructions d'utilisation

ABB

ABB REL 501-C1 2.5 Manuel du produit

ABB

ABB RED670 Relion 670 series Guide de démarrage rapide

ABB

ABB Relion REB500 Instructions d'utilisation

ABB

ABB REM 610 Manuel du produit

ABB

ABB RELION REL650 Manuel utilisateur

Manuels Dispositif de protection populaires d'autres marques

Sola HD

Sola HD STV100K Series Manuel utilisateur

socomec

socomec COUNTIS AMd Manuel utilisateur

Kemo Electronic

Kemo Electronic M148-24 Manuel utilisateur

SK ClickClick Manuel utilisateur

Endress+Hauser

Endress+Hauser HAW569 Manuel utilisateur

Ultrasonic

Ultrasonic SonicPRO Manuel utilisateur

nxt

nxt BIA-nXt-DPC 1-22 Manuel utilisateur

TFortis

TFortis SG-Switch Manuel utilisateur

BERNINI DESIGN

BERNINI DESIGN Be172 Manuel utilisateur

Rayleigh Instruments

Rayleigh Instruments RI-ENERGYSET-3P-ESS-50-100 Manuel utilisateur

GE Multilin 3 Series Manuel utilisateur

E.K.T.

E.K.T. ke-DP01 Manuel utilisateur

Siemens

Siemens SIPROTEC 7SD80 Manuel utilisateur

cias

cias MICRO-RAY Manuel utilisateur

Sungrow

Sungrow PVS-16MH Manuel utilisateur

Reer

Reer 32010 Manuel utilisateur

Tyco

Tyco ESFR-17 Manuel utilisateur

Ross

Ross Opengear SRA-8901-R Manuel utilisateur