ABB ScreenMaster RVG200 Manuel utilisateur

—

ABB MEASUREMENT & ANALYTICS | SERVICE INSTRUCTION

ScreenMaster RVG200

Paperless recorder

Terminal block failures

1 Introduction

There have been instances reported where some or

all inputs on an RVG200 analog input card have

shown as failed immediately after installation, with

no apparent cause for the failure. In rare cases, this

can be attributed to a faulty analog input card but

the most common cause has been identified as a

problem affecting the connection strips within the

terminal block assembly.

The reason for potential failure is that during

installation, unscrewing the terminal connection,

inserting the wire and tightening the screw can

cause the spring assembly inside the terminal block

to move, breaking its contact with the PCB.

2 Action

Action when fault reported Action at next service

Information only Recall instruments

3 Tools/Equipment required

• Medium, flat-bladed screwdriver

• Anti-static strap or anti-static workbench

4 Identifying failures

WARNING

Bodily injury

Isolate all power supplies to the recorder before

removing the terminal cover.

NOTICE

Damage to equipment

The recorder is vulnerable to electrostatic

damage. Wear an anti-static strap or dismantle

the unit on an anti-static workbench.

–

ScreenMaster RVG200

terminal block

SI/RandC/001-EN Rev. A 08.2019

—

We reserve the right to make technical

changes or modify the contents of this

document without prior notice. With

regard to purchase orders, the agreed

particulars shall prevail. ABB does not

accept any responsibility whatsoever for

potential errors or possible lack of

information in this document.

We reserve all rights in this document and

in the subject matter and illustrations

contained therein. Any reproduction,

disclosure to third parties or utilization of

its contents – in whole or in parts – is

forbidden without prior written consent

of ABB.

—

ABB Limited

Measurement & Analytics

Howard Road, St. Neots

Cambridgeshire, PE19 8EU, UK

Tel: +44 (0)870 600 6122

Fax: +44 (0)1480 213 339

Email: instrumen[email protected]

abb.com/measurement

ABB Inc.

Measurement & Analytics

125 E. County Line Road

Warminster, PA 18974

USA

Tel: +1 215 674 6000

Fax: +1 215 674 7183

…4 Identifying failures

Referring to Figure 1:

1 Isolate the recorder from the power supply.

2 Press down into recess Aand pull terminal cover B

away from the case.

3 Insert a flat-bladed screwdriver into each slot Cin turn

(2 slots) to release the locking arm and pull terminal block

Daway from the case.

4 Check the position of spring contacts Ewithin the terminal

block assembly.

The correct position for the contacts is as shown in Figure 1

– each contact must be positioned a minimum of halfway

across the slot in which the module board fits.

5 If a contact is positioned incorrectly or is damaged, replace

the terminal block assembly.

6 Fit the terminal block.

7 Refit terminal cover B.

Figure 1 Examining the terminal block contacts

Autres manuels pour ScreenMaster RVG200

Autres manuels ABB Instrument de mesure

ABB

ABB BAMU-12C Manuel utilisateur

ABB

ABB RGM40 meter Manuel utilisateur

ABB

ABB ProcessMaster FEM630 Manuel utilisateur

ABB

ABB CoriolisMaster FCM2000 Manuel utilisateur

ABB

ABB CoriolisMaster FCB100 Manuel utilisateur

ABB

ABB B23 Manuel utilisateur

ABB

ABB NETA-21 Manuel d'installation

ABB

ABB C1900 Series Manuel utilisateur

ABB

ABB ProcessMaster FEM630 Manuel utilisateur

ABB

ABB FPD350 Torbar Manuel utilisateur

ABB

ABB COMMANDER 1900 Series Mode d'emploi

ABB

ABB EV1 Manuel utilisateur

ABB

ABB ISL-C 600 Manuel utilisateur

ABB

ABB ReliaMod RTBCOVER Manuel utilisateur

ABB

ABB NGC8200 Manuel utilisateur

ABB

ABB MagMaster MF/F Guide de démarrage rapide

ABB

ABB A43 Manuel utilisateur

ABB

ABB CoriolisMaster FCM2000 Manuel d'installation et d'exploitation

ABB

ABB CB-2000 Manuel utilisateur

ABB

ABB Comem OLI Manuel utilisateur

ABB

ABB EasyLine EL3000 Manuel utilisateur

ABB

ABB CM-ENS Manuel utilisateur

ABB

ABB PGC1000 Manuel utilisateur

ABB

ABB SmartMedia SM2000 Instructions d'installation

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur