ABB ACS880-01 Series Manuel utilisateur

English . . . . . . . . .3

English – USA . . .9

Dansk . . . . . . . . .17

Deutsch . . . . . . .23

Español . . . . . . .29

Suomi. . . . . . . . .37

Français. . . . . . .43

Italiano. . . . . . . .49

Nederlands . . . .55

Polski . . . . . . . . .61

Português . . . . .67

Русский . . . . . . .73

Svenska . . . . . . .81

Türkçe . . . . . . . .87

中文. . . . . . . . . . .93

—

ABB INDUSTRIAL DRIVES

ACS880-01 drives

Frames R6 to R9

Quick installation guide

3AUA0000099689 Rev G MUL

EFFECTIVE: 2019-05-08

USA

—

List of related manuals

You can find manuals and other product documents in PDF format on the

Internet. See section Document library on the Internet on the inside of the

back cover. For manuals not available in the Document library, contact your

local ABB representative.

The code below opens an online listing of the manuals applicable to the

product:

Drive hardware manuals and guides Code (English)

ACS880-01 hardware manual 3AUA0000078093

ACS880-01 quick installation guide for frames

R1 to R3

3AUA0000085966

ACS880-01 quick installation guide for frames

R4 and R5

3AUA0000099663

ACS880-01 quick installation guide for frames

R6 to R9

3AUA0000099689

ACS880-01 +P940 drives for cabinet

installation supplement

3AUA0000145446

ACS880-01 assembly drawings for cable entry

boxes of IP21 frames R5 to R9

3AUA0000119627

ACS-AP-x assistant control panels user’s

manual

3AUA0000085685

Vibration dampers for ACS880-01 drives

(frames R4 and R5, option +C131) installation

guide

3AXD50000010497

Vibration dampers for ACS880-01 drives

(frames R6 to R9, option +C131) installation

guide

3AXD50000013389

ACS880-01 +C132 marine type-approved drives

supplement

3AXD50000010521

ACS880-01 +N7502 drives for SynRM motors

(0.8 to 200 kW) supplement

3AXD50000029482

Drive firmware manuals and guides

ACS880 primary control program firmware

manual

3AUA0000085967

Quick start-up guide for ACS880 drives with

primary control program

3AUA0000098062

Option manuals and guides

Manuals and quick guides for I/O extension

modules, fieldbus adapter, etc.

ACS880-01 manuals

EN – Quick installation guide 3

EN – Quick installation guide

This guide instructs briefly how to install the drive. For more detailed instructions,

engineering guide lines, technical data and complete safety instructions, see the

hardware manual (www.abb.com/drives: Select Document Library and search for

document number 3AUA0000078093 [English]).

Obey the safety instructions

The floor material below the drive must be non-flammable.

Check if capacitors need to be reformed

Reform the capacitors if the drive has not been powered (either in storage or unused)

for a year or more.

You can determine the manufacturing date from the serial number, which you find on

the type designation label attached to the drive. The serial number is of format

MYYWWRXXXX. YY and WW tell the manufacturing year and week as follows:

YY: 17, 18, 19, … for 2017, 2018, 2019, …

WW: 01, 02, 03, … for week 1, week 2, week 3, …

For information on reforming the capacitors, see Converter modules with

electrolytic DC capacitors in the DC link capacitor reforming instructions

WARNING! Obey these instructions. If you ignore them, injury or death, or

damage to the equipment can occur:

• Only qualified electrical professionals are allowed to install and maintain the

drive.

• Never work on the drive, motor cable or motor when main power is applied. If

the drive is already connected to the input power, wait for 5 minutes after

disconnecting the input power.

• Never work on the control cables when power is applied to the drive or to the

external control circuits.

• Always ground the drive, the motor and adjoining equipment to the protective

earth (PE) bus of the power supply.

• Make sure that debris from borings and grindings does not enter the drive when

installing.

• Do not connect the drive to a voltage higher than what is marked on the type

designation label.

4 EN – Quick installation guide

(3BFE64059629 [English]), available on the Internet at

www.abb.com/drives/documents.

Select the power cables

Size the power cables according to local regulations to carry the nominal current

given on the type designation label of your drive.

Typical power cable sizes are listed in table Bon page 102. For the conditions of the

sizing, see the hardware manual.

Ensure the cooling

See table Bon page 102 for the losses and the cooling air flow through the drive. The

allowed operating temperature range of the drive without derating is -15 to +40 °C.

Protect the drive and input power cables

See table Bon page 102.

Install the drive on the wall

See figure A on page 101.

Check the compatibility with IT (ungrounded), corner-

grounded delta, midpoint-grounded delta and TT systems

The standard drive with ground-to-phase varistors connected can be installed to a

symmetrically grounded TN-S system. For other systems, see the hardware manual

and ACS880 frames R1 to R11 EMC filter and ground-to-phase varistor

disconnecting instructions (3AUA0000125152 [English]).

EN – Quick installation guide 5

A = TN-S system, B1 = Corner-grounded system, B2 = Midpoint-grounded system, C = IT system

WARNING! Do not install the drive with EMC filter options +E200 and +E202

connected to a system that the filter is not suitable for. This can cause danger,

or damage the drive.

WARNING! Do not install the drive with the ground-to-phase varistor

connected to a system that the varistor is not suitable for. If you do, the varistor

circuit can be damaged. See the drive hardware manual.

Note: With option +E201, remove EMC AC, EMC DC and VAR screws in for systems

other than TN-S if not removed at the factory. For more information, contact ABB.

Check the insulation of the input and motor cables and the

motor

Check the insulation of the input cable according to local regulations before you

connect it to the drive.

See figure Don page 103. Ground the motor cable shield at the motor end. For

minimal interference, make a 360-degree grounding at the cable lead-through, or

keep the pig tail short.

B1 CA

6 EN – Quick installation guide

Check the insulation of the motor cable and motor when the cable is disconnected

from the drive, see figure Eon page 103. Measure the insulation resistance between

each phase conductor and the Protective Earth conductor using a measuring voltage

of 1000 V DC. The insulation resistance of an ABB motor must exceed 100 Mohm

(reference value at 25 °C or 77 °F). For the insulation resistance of other motors,

please consult the manufacturer’s instructions. Note: Moisture inside the motor

casing will reduce the insulation resistance. If moisture is suspected, dry the motor

and repeat the measurement.

Attach the warning stickers in local languages

Connect the power cables

See figures Cand Fon pages 102 and 103. Use symmetrical shielded cable for the

motor cabling.

1. Remove the front cover. IP21 units: Release the retaining clip with a screwdriver

(a) and lift the cover from the bottom outwards (b).

2. IP21 units: Remove the cable entry box cover by undoing the mounting screws.

3. Attach the residual voltage warning sticker in the local language next to the

control unit.

4. Remove the side plates of the cable entry box.

5. Remove the shroud on the power cable terminals by releasing the clips on the

sides with a screwdriver and lifting (a). Knock out holes for the cables (b).

6. For frames R8 and R9: If parallel cables are installed, knock out the shrouds on

the power cable terminals for the cables to be installed.

7. Cut adequate holes into the rubber grommets. Slide the grommets onto the

cables. Prepare the cable ends. Slide the cables through the holes of the bottom

plate and attach the grommets to the holes.

8. Ground the cable shields 360 degrees under the grounding clamps.

9. Connect the twisted cable shields to the grounding terminals.

10. Connect the conductors of the input and motor cables. Tighten the screws.

11. Units with option +D150: Connect the conductors of the brake resistor cable to the

R+ and R- terminals.

12. If parallel cables are installed, install the grounding shelf for them. Repeat steps 7

to 12.

13. Reinstall the shroud on the power terminals.

14. Reinstall the side plates of the cable entry box.

15. Secure the cables outside the unit mechanically.

EN – Quick installation guide 7

Connect the control cables

See figure G.

1. Install the control cable grounding shelf in the cable entry box.

2. Cut adequate holes into the rubber grommets and slide the grommets onto the

cables. Slide the cables through the holes of the bottom plate and attach the

grommets to the holes.

3. Strip the cable ends and cut to suitable length (note the extra length of the

grounding conductors).

4. Ground the outer shields of all control cables 360 degrees at a grounding clamp in

the cable entry box.

5. Ground the pair-cable shields to a grounding clamp below the control board.

Leave the other end of the shields unconnected or ground them indirectly via a

high-frequency capacitor with a few nanofarads, eg, 3.3 nF / 630 V.

6. Connect the conductors to the appropriate terminals of the control board (see

page 8).

7. Wire the optional modules if included in the delivery.

8. Reinstall the front cover.

Note for fieldbus cabling. See figure H.

1. Install the additional grounding shelf.

2. Ground the outer shields of the cables 360 degrees at a grounding clamp.

3. Knock out holes in the cable entry box cover for the cables to be installed. Install

the cable entry box cover.

4. Plug the connector to the fieldbus module.

Default I/O connections

The default I/O connections of the Factory macro of the ACS880 primary control

program are shown below.

8 EN – Quick installation guide

XPOW External power input

1+24VI 24 V DC, 2 A

2GND

XAI Reference voltage and analog inputs

1+VREF 10 V DC, RL1…10 kohm

2-VREF -10 V DC, RL1…10 kohm

3AGND Ground

4AI1+ Speed reference 0(2)…10 V, Rin >

200 kohm

5AI1-

6AI2+ By default not in use. 0(4)…20 mA, Rin =

100 ohm

7AI2-

J1 J1 AI1 current/voltage selection jumper

J2 J2 AI2 current/voltage selection jumper

XAO Analog outputs

1AO1 Motor speed rpm 0…20 mA, RL<

500 ohm

2AGND

3AO2 Motor current 0…20 mA, RL< 500 ohm

4AGND

XD2D Drive-to-drive link

Drive-to-drive link

3BGND

J3 J3 Drive-to-drive link termination switch

XRO1, XRO2, XRO3 Relay outputs

11 NC Ready

250 V AC / 30 V DC

2 A

12 COM

13 NO

21 NC Running

250 V AC / 30 V DC

2 A

22 COM

23 NO

31 NC Faulted(-1)

250 V AC / 30 V DC

2 A

32 COM

33 NO

XD24 Digital interlock

1DIIL Run enable

2+24VD +24 V DC 200 mA 1)

3DICOM Digital input ground

4+24VD +24 V DC 200 mA 1)

5DIOGND Digital input/output ground

J6 Ground selection switch

XDIO Digital input/outputs

1DIO1 Output: Ready

2DIO2 Output: Running

XDI Digital inputs

1DI1 Stop (0) / Start (1)

2DI2 Forward (0) / Reverse (1)

3DI3 Reset

4DI4 Acceleration & deceleration select

5DI5 Constant speed 1 (1 = On)

6DI6 By default not in use.

XSTO Safe torque off

1OUT1

Safe torque off. Both circuits must be

closed for the drive to start.

2SGND

3IN1

4IN2

X12 Safety functions module connection

X13 Control panel connection

X205 Memory unit connection

Wire sizes:

0.5 … 2.5 mm2

(24…12 AWG)

Tightening

torques: 0.5 N·m

(5 lbf·in) for both

stranded and

solid wiring.

1) Total load

capacity of these

outputs is 4.8 W

(200 mA / 24 V)

minus the power

taken by DIO1 and

DIO2.

Fault

EN – USA quick installation guide 9

USA

EN – USA quick installation guide

This guide instructs briefly how to install the drive. For more detailed instructions,

engineering guide lines, technical data and complete safety instructions, see the

hardware manual (www.abb.com/drives: Select Document Library and search for

document number 3AUA0000078093 [English]).

Obey the safety instructions

The floor material below the drive must be non-flammable.

Check if capacitors need to be reformed

Reform the capacitors if the drive has not been powered (either in storage or unused)

for a year or more.

You can determine the manufacturing date from the serial number, which you find on

the type designation label attached to the drive. The serial number is of format

MYYWWRXXXX. YY and WW tell the manufacturing year and week as follows:

YY: 17, 18, 19, … for 2017, 2018, 2019, …

WW: 01, 02, 03, … for week 1, week 2, week 3, …

For information on reforming the capacitors, see Converter modules with

electrolytic DC capacitors in the DC link capacitor reforming instructions

WARNING! Obey these instructions. If you ignore them, injury or death, or

damage to the equipment can occur:

• Only qualified electrical professionals are allowed to install and maintain the

drive.

• Never work on the drive, motor cable or motor when main power is applied. If

the drive is already connected to the input power, wait for 5 minutes after

disconnecting the input power.

• Never work on the control cables when power is applied to the drive or to the

external control circuits.

• Always ground the drive, the motor and adjoining equipment to the protective

earth (PE) bus of the power supply.

• Make sure that debris from borings and grindings does not enter the drive when

installing.

• Do not connect the drive to a voltage higher than what is marked on the type

designation label.

10 EN – USA quick installation guide

USA

(3BFE64059629 [English]), available on the Internet at

www.abb.com/drives/documents.

Select the power cables

Size the power cables according to local regulations to carry the nominal current

given on the type designation label of your drive.

Typical power cable sizes are listed in table Bon page 102. For the conditions of the

sizing, see the hardware manual.

Ensure the cooling

See table Aon page 105 for the losses and the cooling air flow through the drive. The

allowed operating temperature range of the drive without derating is -15 to +40 °C.

Protect the drive and input power cable

See table Aon page 105 for the UL class T fuses for branch circuit protection per

NEC. Check that the operating time of the fuse is below 0.5 seconds for frame R6

and below 0.1 seconds for frames R7 to R9. Obey local regulations.

Install the drive on the wall

See figure A on page 101. For UL Type 12 drives: Install also the hood to the drive.

Check the compatibility with IT (ungrounded), corner-

grounded delta, midpoint-grounded delta and TT systems

The standard drive with ground-to-phase varistors connected can be installed to a

symmetrically grounded TN-S system. For other systems, see the hardware manual

and ACS880 frames R1 to R11 EMC filter and ground-to-phase varistor

disconnecting instructions (3AUA0000125152 [English]).

Autres manuels pour ACS880-01 Series

Autres manuels ABB Entraînement CC

ABB

ABB ACS880 Series Manuel d'utilisation et d'entretien

ABB

ABB ACQ580-34 Manuel utilisateur

ABB

ABB ACS880-07 Manuel utilisateur

ABB

ABB ACS310 Manuel utilisateur

ABB

ABB ACS880+N5350 Manuel utilisateur

ABB

ABB ACS510-01 Manuel utilisateur

ABB

ABB ACSM1 Series Manuel d'utilisation et d'entretien

ABB

ABB ACS580-0P Manuel utilisateur

ABB

ABB RSYC-01 Manuel utilisateur

ABB

ABB ACH580-01 Series Manuel utilisateur

ABB

ABB ACS850 series Manuel utilisateur

ABB

ABB ACS6080 Manuel utilisateur

ABB

ABB ACS355 series Manuel utilisateur

ABB

ABB ACQ580-04 Manuel utilisateur

ABB

ABB ACQ580-04 Manuel utilisateur

ABB

ABB Terra HP Generation 3 CE Manuel utilisateur

ABB

ABB ACx580-01 Series Manuel utilisateur

ABB

ABB ACS880-04 drive modules Guide de l'utilisateur

ABB

ABB ACS880-11 Manuel utilisateur

ABB

ABB ACS880-01 Series Manuel utilisateur

ABB

ABB +Q951 Manuel utilisateur

ABB

ABB HP CP500 Manuel utilisateur

ABB

ABB ACS2000 AFE 1MVA Manuel utilisateur

ABB

ABB ACS850 series Manuel utilisateur

Manuels Entraînement CC populaires d'autres marques

Vincent Associates

Vincent Associates UNIBLITZ ED12DSS Manuel utilisateur

EKSMA OPTICS

EKSMA OPTICS DQ-100-4 Manuel de la liste des pièces

Chamberlain Garog

Chamberlain Garog D Series Manuel utilisateur

Parker

Parker PDS Series Manuel utilisateur

Festo

Festo DGC G Series Guide de configuration

Binks

Binks QS-5012-1-CE Manuel utilisateur

Danfoss

Danfoss VLT 2800 Series Fiche technique

YASKAWA

YASKAWA CANopen SI-S3 Manuel utilisateur

GE D20A6 Manuel utilisateur

Unex

Unex MC-D-250-1000-050W-TW Manuel utilisateur

Geckodrive

Geckodrive G213V Manuel utilisateur

Rockwell Automation

Rockwell Automation PowerFlex 700S Manuel du propriétaire

WEG

WEG DeviceNet CFW500 Manuel utilisateur

Siemens

Siemens SINAMICS G Fiche technique

Siemens

Siemens SINAMICS SM150 6SL3815-7NP41-0AA1 Mode d'emploi

SOMFY

SOMFY JR RU 30 Manuel utilisateur

Beckhoff

Beckhoff AX8911 Manuel de l'opérateur

Minarik

Minarik MM300 Series Manuel utilisateur